Zanussi Zwg 680 P User Manual

							Before Loading The Laundry
Important! Make
sure that no metal
objects are left in the
laundry (e.g. hair
clips, safety pins,
pins). Button up pil-
lowcases, close zip
fasteners, hooks and
poppers. Tie any
belts or long tapes.
Remove any hooks
(e.g curtains).
• Never wash whites and coloureds together.
Whites may lose their «whiteness» in the
wash.
• New coloured items may run in the first
wash; they should therefore be washed sep-
arately the first time.
• Rub particularly soiled areas with a special
detergent or detergent paste.
• Treat curtains with special care.
• Wash the socks and the gloves inside the
bag or a net.
Remove stubborn stains before washing:
Blood: treat fresh stains with cold water. For
dried stains, soak overnight in water with a spe-
cial detergent then rub in the soap and water.
Oil based paint: moisten with benzine stain
remover, lay the garment on a soft cloth and
dab the stain; treat several times.
Dried grease stains: moisten with turpentine,
lay the garment on a soft surface and dab the
stain with the fingertips and a cotton cloth.
Rust: oxalic acid dissolved in hot water or a
rust removing product used cold. Be careful
with rust stains which are not recent since the
cellulose structure will already have been dam-
aged and the fabric tends to hole.
Mould stains: treat with bleach, rinse well
(whites and fast coloureds only).
Grass: soap lightly and treat with bleach
(whites and fast coloureds only).
Ball point pen and glue: moisten with ace-
tone1), lay the garment on a soft cloth and dab
the stain.
Lipstick: moisten with acetone as above, then
treat stains with methylated spirits. Treat any re-
sidual marks with bleach.
Red wine: soak in water and detergent, rinse
and treat with acetic or citric acid, then rinse.
Treat any residual marks with bleach.
Ink: depending on the type of ink, moisten the
fabric first with acetone
1), then with acetic acid;
treat any residual marks on white fabrics with
bleach and then rinse thoroughly.
Tar stains: first treat with stain remover, me-
thylated spirits or benzine, then rub with deter-
gent paste.
Open the door by carefully pulling the
door handle outwards
Load the laundry
Place the laundry in
the drum, one item at
a time, shaking them
out as much as pos-
sible.
Maximum Loads
Recommended loads are indicated in the
«Washing Programmes».
General rules:
•Cotton, linen: drum full but not too tightly
packed;
•Synthetics: drum no more than half full;
•Delicate fabrics and woollens: drum no
more than one third full.
1) do not use acetone on artificial silk.
 11 www.zanussi.com
 
						

							Close the door gently
Warning! Make
sure that any
fabrics were not trap-
ped when closing the
door.
Detergents and additives
Good washing results also depend on the
choice of detergent and use of the correct
quantities to avoid waste and protect the envi-
ronment.
Although biodegradable, detergents contain
substances which, in large quantities, can up-
set the delicate balance of nature.
The choice of detergent will depend on the
type of fabric (delicates, woollens, cottons,
etc.), the colour, washing temperature and de-
gree of soiling.
All commonly available washing machine deter-
gents may be used in this appliance:
• powder detergents for all types of fabric,
• powder detergents for delicate fabrics (40°C
max) and woollens,
• liquid detergents, preferably for low tempera-
ture wash programmes (60°C max) for all
types of fabric, or special for woollens only.
Quantity of detergent to be used
The type and quantity of detergent will depend
on the type of fabric, load size, degree of soiling
and hardness of the water used.
For the quantity of detergent, refer always to
what is written on the product packing.
Use less detergent if:
• you are washing a small load,
• the laundry is lightly soiled,
• large amounts of foam form during washing.
Degrees of water hardness
Water hardness is classified in so-called “de-
grees” of hardness. Information on hardness of
the water in your area can be obtained from the
relevant water supply company, or from your lo-
cal authority.
If the water hardness degree is medium or high
we suggest you to add a water softener follow-
ing always the manufacturer’s instructions.
When the degree of hardness is soft, readjust
the quantity of the detergent.
Open the detergent dispenser drawer
 Compartment for
powder or liquid de-
tergent used for main
wash. 
 Compart-
ment for liquid addi-
tives (fabric softener,
starch).
Warning! If you wish to carry out the
prewash, pour the detergent among
washing items into the drum.
Warning! Depending on the type
detergent you use (powder of liquid),
ensure that the flap, placed in the main wash
compartment, is in the desired position.
Flap for powder or liquid detergent
UP- Flap position
if using POWDER
detergentDOWN - Flap posi-
tion if using LIQ-
UID detergent dur-
ing main wash
PUSHREMOVE
TO 
CLEANPUSHREMOVE
TO 
CLEAN
If the flap is not in the desired position:
12
 www.zanussi.com
 
						

							• Remove the drawer. Push the drawer edge
outwards where indicated by the arrow
(PUSH) to facilitate drawer removal.
The flap is down and you wish to use
powder detergent:
• Rotate the flap up-
wards. Ensure to fit
the flap completely
in.
• Carefully put the
drawer back.
• Measure out the
detergent.
• Pour the powder
detergent into the
main wash com-
partment 
 .
The flap is up and you wish to use liquid
detergent:
• Rotate the flap
downwards.
• Carefully put the
drawer back.
• Measure out the detergent.
For the quantity of detergent, refer al-
ways to what is written on the product
packing and ensure that the detergent can be
poured in the drawer.
• Pour the liquid detergent in the compart-
ment 
 without exceeding the limit indica-
ted in the flap. The detergent must be
placed in the appropriate compartments of
the dispenser drawer before starting the
wash programme.
Warning! Do not use the flap in "DOWN"
position with:
• Gelatinous detergent or thick detergent.
• Powder detergent.
• With programmes with prewash.
• Do not use liquid detergent if the washing
programme doesn't start immediately.
In all above listed cases, use the flap in
"UP" position .
Measure out the fabric softener
Pour fabric softener
or any additives into
the compartment
marked 
 (do not
exceed the «MAX»
mark in the drawer).
Any additives must
be placed in the ap-
propriate compart-
ments of the dispens-
er drawer just before
starting the wash pro-
gramme.
Close the detergent dispenser drawer
 13 www.zanussi.com
 
						

							Set your washing programme
The control panel permits to select a washing programmes and different options.
When an option button is selected, the corresponding pilot light is on. Otherwise it is off.
For compatibility among washing programmes and options, see the "Washing Programme
Chart". If an incorrect option is selected, the integrated red pilot light of the button 6 flashes
3 times.
123465
7.1
7.2
7.3
1
Programme selector di-
al
Turn the programme selector dial to the required pro-
gramme. The selector dial can be turned either clock-
wise or counter-clockwise. The green pilot light of the but-
ton 6 starts flashing: the appliance is now switched on.
If you turn the programme selector dial to another pro-
gramme when the appliance is working, the red pilot light
of the button 6 will flash 3 times to indicate a wrong selection.
The appliance will not perform the new selected programme.
• To switch the appliance off, turn the programme selector
dial to the position 
 .
• To cancel or change a running programme, switch the ap-
pliance off by turning the programme selector dial to the po-
sition 
 . Select the new programme by turning the selec-
tor to the desired programme. Start the new programme by
pressing the button 6 again. The water in the tub will be not
emptied out.
14
 www.zanussi.com
 
						

							2
Temperature button
95°
60°
40°
30°
Push the temperature button to select the most suita-
ble temperature for washing your laundry .
3
Automatic Spin reduc-
tion and Rinse Hold
AUTO
By selecting a programme, the appliance proposes automati-
cally the maximum spin speed provided for that programme.
By selecting Automatic Spin reduction the spin speed is re-
duced to a half, but not less than 400 rpm. The relevant light
illuminates.
 Rinse Hold
By selecting this function the water of the last rinse is not
emptied out to prevent the fabrics from creasing. Before
opening the door it will be necessary to empty out the water.
To empty out the water, please read the paragraph «At
the end of the programme».
4
Super QuickBy pressing this button the corresponding pilot light illumi-
nates.
Short cycle for lightly soiled items or for laundry which needs
only freshening up.
With this option, a reduced load of laundry is recommended:
• Cottons 3 kg
• Synthetics and delicates 1,5 kg
 Extra Rinse
This appliance is designed for saving water. However, for peo-
ple with very delicate skin (allergic to detergents) it may be
necessary to rinse the laundry using an extra quantity of water.
Press simultaneously the buttons 3 and 4 for some seconds:
the pilot light 7.2 comes on. This function stays permanently
on. To remove it press the same buttons again until the pilot
light 7.2 goes off.
 15 www.zanussi.com
 
						

							5
Delay Start
3H
6H
9H
The start of the programme can be delayed by 9, 6 or 3 hours
by means of this button. The relevant light illuminates.
You must select this option after you have set the programme
and before you start the programme.
Select a delayed start:
• select the programme and the required options;
• select the delay start by pressing the button 5;
• press the button 6:
– the appliance starts its hourly countdown.
– The programme will start after the selected delay has ex-
pired.
Cancelling the delayed start after having started the
programme:
• set the appliance to PAUSE by pressing the button 6;
• press the button 5 once, the light relevant to the selected
delay goes off;
• press the button 6 again to start the programme.
The DELAY START cannot be selected with the drain pro-
gramme.
Important! The selected delay can be changed only after se-
lecting the washing programme again. The door will be locked
throughout the delay time. If you need to open the door, you
must set the appliance to PAUSE (by pressing the button 6)
and then wait a few minutes. After you have closed the door,
press the button 6 again.
16
 
www.zanussi.com
 
						

							6
Start/Pause
Start the programme by pressing the button 6
• To start the selected programme, press the button 6, the
corresponding green pilot light stops flashing. The pilot light
7.1 illuminates to indicate that the appliance starts operat-
ing and the door is locked. If you have chosen a delayed
start, the appliance will begin the countdown.
• To interrupt a programme which is running, press the but-
ton 6: the corresponding green pilot light starts flashing. It
is possible to change some options of a running pro-
gramme before the programme carries them out.
• To restart the programme from the point at which it was in-
terrupted, press the button 6.
• After the programme has started the door is locked. If, for
any reason, you need to open the door, set firstly the ap-
pliance to PAUSE by pressing the button 6. After a few mi-
nutes it will be possible to open the door.
If the door remains locked, this means that the appliance is
already heating or that the water level is too high. In any
case, do not try to force the door!
If you cannot open the door but you need to open it you
have to switch the appliance off by turning the selector dial
to 
 . After a few minutes the door can be opened (pay
attention to the water level and temperature!). After
closing the door, it is necessary to select the programme
and options again and to press the button 6.
7.1
7.2
7.3
Indicator pilot lights• When you start the programme by pressing the button 6,
the washing phase pilot light (7.1) illuminates. This means
that the appliance is operating.
• The additional rinses pilot light (7.2) illuminates when the
appliance performs an extra rinse.
• When the programme has finished the end cycle pilot light
(7.3) comes on.
At the end of the programme
The appliance stops automatically. The pilot
light of the button 6 and the pilot light corre-
sponding to the just finished washing phase go
off. The light 7.3 illuminates.
If a programme or an option that ends with wa-
ter left in the tub has been selected and the
door remains locked to indicate that the water
must be emptied out before opening the door.
Follow the below instructions to empty out the
water:
•
Turn the programme selector dial to  .
• Select the draining or spinning programme.
• Reduce the spin speed if needed, by press-
ing the relevant button.
• Press the button 6.
At the end of the programme, the door can be
now opened. Turn the programme selector dial
to 
 to switch the appliance off.
Remove the laundry from the drum and carefully
check that the drum is empty. If you do not in-
tend to carry out another wash, close the water
 17 www.zanussi.com
 
						

							tap. Leave the door open to prevent the forma-
tion of mildew and unpleasant smells.
Warning! If there are children or pets in
the house, activate the child safety de-
vice in the inner side of the door frame (for
more details read " Child safety" in the chapter
"Safety Information").
Stand by: during programme setting up
and once the programme has finished, if
the programme selector dial and any button are
not touched, after a few minutes the energy
saving system is enabled. The pilot lights go off.
The green pilot light of the button 6 flashes with
a low frequency. By pressing any button theappliance will come out of the energy saving
status.
Door seal
At the end of every
cycle, check from the
door seal and remove
objects that could be
trapped in the fold.
Washing programmes
Programme - Maximum and Minimum Temperature -
Cycle Description - Maximum Spin Speed - Maximum
Fabrics Load - Type of LaundryOptionsDetergent
Compartment
 COTTON
95°- 
 (Cold)
Main wash - Rinses - Maximum spin speed at: 800 rpm for
model ZWG 680P; 1000 rpm for model ZWG 6100P
Max. load 6 kg - Reduced load 3 kg
White, coloured cotton and linen. Normally soiled items.
AUTOMATIC SPIN RE-
DUCTION,
RINSE HOLD,
DELAY START,
SUPER QUICK
1),
EXTRA RINSE
 +  COTTON WITH PREWASH
95°- 
 (Cold)
Prewash - Main wash - Rinses - Maximum spin speed at: 800
rpm for model ZWG 680P; 1000 rpm for model ZWG 6100P
Max. load 6 kg - Reduced load 3 kg
White, coloured cotton and linen. Heavy soiled items.
AUTOMATIC SPIN RE-
DUCTION,
RINSE HOLD,
DELAY START,
SUPER QUICK
1),
EXTRA RINSE
  COTTON ECONOMY2)
60° - 40°
Main wash - Rinses - Maximum spin speed at: 800 rpm for
model ZWG 680P; 1000 rpm for model ZWG 6100P
Max. load 6 kg
White and coloured cotton. This programme can be selec-
ted for slightly or normally soiled cotton items. The tempera-
ture will decrease and the washing time will be extended. This
allows to obtain a good washing efficiency by saving energy.AUTOMATIC SPIN RE-
DUCTION,
RINSE HOLD,
DELAY START,
EXTRA RINSE
 SYNTHETIC
60° - 
 (Cold)
Main wash - Rinses - Maximum spin speed at: 800 rpm for
model ZWG 680P; 1000 rpm for model ZWG 6100P
Max. load 3 kg - Reduced load 1,5 kg
Synthetic or mixed fabrics: underwear, coloured garments,
non-shrink shirts, blouses . Normally soiled items.AUTOMATIC SPIN RE-
DUCTION,
RINSE HOLD,
DELAY START,
SUPER QUICK
1),
EXTRA RINSE
18
 www.zanussi.com
 
						

							Programme - Maximum and Minimum Temperature -
Cycle Description - Maximum Spin Speed - Maximum
Fabrics Load - Type of LaundryOptionsDetergent
Compartment
 MIXED FABRIC
Cold
Main wash - Rinses - Maximum spin speed at: 800 rpm for
model ZWG 680P; 1000 rpm for model ZWG 6100P
Max. load 3 kg
Highly energy efficient cold wash programme for lightly soiled
laundry. This programme requires a detergent which is active
in cold water.
AUTOMATIC SPIN RE-
DUCTION,
RINSE HOLD,
DELAY START,
EXTRA RINSE
 DELICATE
40°- 
 (Cold)
Main wash - Rinses - Maximum spin speed at 700 rpm
Max. load kg 3 - Reduced load 1,5 kg
Delicate fabrics: acrylics, viscose, polyester . Normally
soiled items.
AUTOMATIC SPIN RE-
DUCTION,
RINSE HOLD,
DELAY START,
SUPER QUICK
1),
EXTRA RINSE
  WOOL / HANDWASH
40°- 
 (Cold)
Main wash - Rinses - Maximum spin speed: at 800 rpm for
model ZWG 680P; 1000 rpm for model ZWG 6100P
Max. load 2 kg
Machine washable wool, hand washable woollens and
delicate fabrics with «hand washing» care symbol.
Note: A single or bulky item may cause imbalance. If the ap-
pliance doesn’t perform the final spin phase, add more items,
redistribute the load manually and then select the spinning
programme.
AUTOMATIC SPIN RE-
DUCTION,
RINSE HOLD,
DELAY START
 RINSE
Rinse - Short spin speed at 700 rpm
Max. load 6 kg
To rinse and spin cotton garments which have been washed
by hand. Select the EXTRA RINSE option to intensify the rins-
ing action. The appliance adds additional rinses.AUTOMATIC SPIN RE-
DUCTION,
RINSE HOLD,
DELAY START,
EXTRA RINSE
 DRAIN
Draining of water
For emptying out the water left in the drum in the programmes
with Rinse Hold option.  
 SPIN
Drain and long spin at maximum spin speed: 800 rpm for
model ZWG 680P; 1000 rpm for model ZWG 6100P
Max. load 6 kg
Separate spin for hand washed garments and after pro-
grammes with the Rinse Hold option selected. If the Automat-
ic Spin reduction is selected, by pressing the relevant button,
the appliance performs a short spin.
AUTOMATIC SPIN RE-
DUCTION,
DELAY START
 
 19 www.zanussi.com
 
						

							Programme - Maximum and Minimum Temperature -
Cycle Description - Maximum Spin Speed - Maximum
Fabrics Load - Type of LaundryOptionsDetergent
Compartment
 EASY IRON
40°- Cold
Main wash - Rinses - Maximum spin speed at 900 rpm
In order to obtain the best anti-creasing result, reduce the
load of synthetics items. (Recommended load 1 Kg)
Synthetic or mixed fabrics. Gentle wash and spin to avoid
any creasing. The appliance performs additional rinses.AUTOMATIC SPIN RE-
DUCTION,
RINSE HOLD,
DELAY START,
EXTRA RINSE
 5 SHIRTS
30°
Main wash - Rinses - Maximum spin speed at 900 rpm
Synthetics and mixed fabrics. Suitable for 5 - 6 shirts
lightly soiled.AUTOMATIC SPIN RE-
DUCTION,
DELAY START
 MINI 30
30°
Main wash - Rinses - Maximum spin speed at 700 rpm
Max. load 2 kg
Synthetics and delicates. Lightly soiled items or which only
needs freshening up.
AUTOMATIC SPIN RE-
DUCTION,
DELAY START
 JEANS
60°- Cold
Main wash - Rinses - Maximum spin speed at: 800 rpm for
model ZWG 680P; 1000 rpm for model ZWG 6100P
Max. load 3 kg
Trousers, shirts or jackets in denim and jersey realized with hi-
tech materials. The Extra Rinse option is activated automati-
cally.
AUTOMATIC SPIN RE-
DUCTION,
RINSE HOLD,
DELAY START
1) If you select the SUPER QUICK option by pressing button 4, we recommend that you reduce the maximum
load as indicated. Full loading is possible however with somewhat reduced cleaning results.
2) Standard programmes for the Energy Label consumption values
According to regulation 1061/2010, the “ Cotton ECO 60 °C ” and “ Cotton ECO 40 °C ” are respectively
the “standard 60 °C cotton programme” and the “standard 40 °C cotton programme”. They are the most
efficient programmes in terms of combined energy and water consumptions for washing normally soiled
cotton laundry.
The water temperature of the washing phase may differ from the temperature declared for the selected
programme.
Consumption values
The data of this table are approximate. Different causes can change the data: the quantity and
type of laundry, the water and ambient temperature.
20
 www.zanussi.com