Zanussi Zwf 145 W User Manual

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
         
       Mould: Mould stains should be cleaned as soon as possible. The 
       stain should be washed with detergent, and if it does not     
       disappear, it should be wiped with oxygenated water (in      
       proportion of 3%). 
 
       Ink: Hold the stained area under cold water and wait until the inky 
       water completely runs off. Then rub with water diluted with...

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
FAILURE PROBABLE CAUSE METHODS OF 
ELIMINATION 
It is unplugged. Insert the plug into the 
socket. 
Your fuse is defected.  Change your fuse. 
The electric power is 
off. Check the electric 
power. 
Start/pause button has 
not been pressed. Press the start/pause 
button. 
The program knob is in 
O(off) status. Bring the program 
knob on the desired 
status. 
Your machine does not...

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
FAILURE PROBABLE CAUSE METHODS OF 
ELIMINATION 
There is a small 
amount of clothes in 
the device. It does not prevent 
operation of the 
machine. 
Excessive amount of 
clothes are filled in the 
machine or the clothes 
are not placed  in a 
well-balanced manner. Do not exceed the 
recommended quantity 
of clothes and spread 
your clothes in the 
machine in a well-
balanced manner....

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  
FAILURE PROBABLE CAUSE METHODS OF 
ELIMINATION 
Clothes exceeding the 
maximum capacity  
has been filled in your 
machine. Put the clothes in your 
machine in a manner 
not to exceed its 
maximum capacity. 
Your water may be 
hard. Use the amount of 
detergent according to 
the declaration of the 
detergent producer. The washing result is 
not good. 
Distribution of the 
clothes in...

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
FAILURE PROBABLE CAUSE METHODS OF 
ELIMINATION 
The spining process is 
not done or  starts with 
delay . No failure. The 
unbalanced load 
control may works in 
that way. The unbalanced load 
control system will try 
to distribute your 
clothes in a 
homogenous manner. 
After your clothes are 
distributed, passage to 
spining process will be 
realized.In the next 
washing process,place...

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
FAILURE 
CODE FAILURE 
INDICATOR PROBABLE 
FAILURE THE PROCESS 
TO BE DONE 
Err 02 The program 
ready light 
blinks. The water level 
in your machine 
is below heater. 
The pressure of 
your water 
supply may be 
low or locking. Turn on the tap 
to the end.Water 
may be cut, 
check it.If the 
problem is still 
continuing,your 
machine will 
automatically 
stop after a 
while.Unplug...

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
FAILURE 
CODE FAILURE 
INDICATOR PROBABLE 
FAILURE THE PROCESS 
TO BE DONE 
Err 05 The start/pause 
light and program 
end light blink. The heater of your 
machine or the 
heat sensor has 
failed. Shut down your 
machine and 
unplug. Turn off 
your tap and apply 
to the nearest 
authorized service. 
Err 06 The program 
ready light and 
program end light 
blink. The motor has 
failed....

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
SECTION 10: INTERNATIONAL WASHING SIGNS
 
 
 
     
Washing 
temparature. Do not wash 
(hand wash) Lukewarm iron.  Medium hot iron. 
 
 
 
     
Hot iron.  Do not iron. Do not tumble 
dry. Hang to dry. 
 
 
 
     
Drip dry.  Dry flat.  Do not bleach.  Handy to bleach. 
 
 
 
   
All of these are dry cleaning symbols. The letters are 
to instruct the cleaner what type of solvent to be...