Zanussi Zwf 145 W User Manual

							 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
         
       Mould: Mould stains should be cleaned as soon as possible. The 
       stain should be washed with detergent, and if it does not     
       disappear, it should be wiped with oxygenated water (in      
       proportion of 3%). 
 
       Ink: Hold the stained area under cold water and wait until the inky 
       water completely runs off. Then rub with water diluted with lemon 
       juice and detergent, wash after waiting for 5 minutes. 
 
       Fruit: Stretch the stained area of your clothes on the top of a     
       container and pour cold water on it. Do not pour hot water on the 
       stain. Wipe with cold water and apply glycerine. W ait for 1-2 hours 
       and rinse after wiping with a few drops of white vinegar.   
 
       Grass stain: Rub the stained part with detergent. If the type of 
       fabric is suitable for use of lye, wash it with lye. Rub your woolen 
       clothes with alcohol.(For coloured ones, a mixture of 1 unit pure 
       alcohol and 2 units of water). 
 
       Oil Paint:The stain should be eliminated before it dries by      
       applying thinner on it. Then it should be rubbed with detergent and 
       washed. 
 
       Burnt stain: If your cloth is suitable for use of lye, you can add lye 
       into your washing water. For woolen fabric, a cloth damped in 
       oxygenated water should be covered on the stain and it should be 
       ironed with a dry cloth on it. It should be washed after rinsing well.   
 
   
 
SECTION 8: AVOIDING MINOR FAULTS 
 
All repairing which must be done on the machine should be done by  
authorized service. W hen a repairing is required for your machine or you are 
unable to eliminate the failure with the help of the information given below: 
 
•  Unplug the machine. 
•  Close the water tap. 
•  Apply to the nearest authorized service station. 
 
 20 
 
						

							 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
FAILURE PROBABLE CAUSE METHODS OF 
ELIMINATION 
It is unplugged. Insert the plug into the 
socket. 
Your fuse is defected.  Change your fuse. 
The electric power is 
off. Check the electric 
power. 
Start/pause button has 
not been pressed. Press the start/pause 
button. 
The program knob is in 
O(off) status. Bring the program 
knob on the desired 
status. 
Your machine does not 
operate. 
The door is not shut 
properly. Shut the door properly. 
You should hear the 
click. 
Water tap is closed.  Open water tap. 
The water inlet hose 
may be bent. Check the water inlet 
hose. 
The water inlet hose is 
obstructed. Clean the filters of 
water inlet hose. (*) 
The valve inlet filter is 
obstructed. Clean the valve inlet 
filters. (*) 
Your machine does not 
receive water. 
The door is not shut 
properly. Shut the door properly. 
You should hear the 
click. 
The drain hose is 
obstructed or bent. Check the drain hose. 
The pump filter is 
obstructed. Clean the pump filter. 
(*) Your machine is not 
draining water. 
The clothes are not 
placed inside the 
machine in a well-
balanced  manner. Spread the clothes 
inside the machine in 
an orderly and well-
balanced manner. 
The feet of your 
machine are not 
adjusted. Adjust the feet. (**) 
Your machine is 
vibrating. 
Transportation screws 
are not removed. Remove transportation 
screws. (**) 
 
(*)See the section concerning the maintenance and cleaning of your machine. 
(**)See the section concerning installations your machine. 
 
        
 21 
 
						

							 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
FAILURE PROBABLE CAUSE METHODS OF 
ELIMINATION 
There is a small 
amount of clothes in 
the device. It does not prevent 
operation of the 
machine. 
Excessive amount of 
clothes are filled in the 
machine or the clothes 
are not placed  in a 
well-balanced manner. Do not exceed the 
recommended quantity 
of clothes and spread 
your clothes in the 
machine in a well-
balanced manner. 
Your machine is 
vibrating. 
Your machine touches 
a ripid object.  Prevent your 
machine’s leaning on a 
tough place . 
Too much detergent 
has been used. Press the start/pause 
button.In order to stop 
the foam,dilute one 
table-spoon of softener 
in half liter of water and 
pour it in the detergent 
drawer.Press the 
start/pause button after 
5-10 minutes.Arrange 
the amount of the 
detergent properly in 
the next washing 
process. 
Excessive foam in the 
detergent drawer. 
Wrong detergent has 
been used. Use only the 
detergents produced 
for full automatic 
machines. 
Your laundry too dirty 
for the program you 
have selected.  Select a suitable 
program. (see Table-1) 
The washing result is 
bad. 
The amount of 
detergent used is not 
sufficient. Use more detergent 
according to the 
detergent. 
 
  
 22 
 
						

							 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  
FAILURE PROBABLE CAUSE METHODS OF 
ELIMINATION 
Clothes exceeding the 
maximum capacity  
has been filled in your 
machine. Put the clothes in your 
machine in a manner 
not to exceed its 
maximum capacity. 
Your water may be 
hard. Use the amount of 
detergent according to 
the declaration of the 
detergent producer. The washing result is 
not good. 
Distribution of the 
clothes in your 
machine is not well-
balanced. Spread the clothes 
inside the machine in 
an orderly and well-
balanced manner .  
The water is drained 
from the machine as 
soon as it is filled. The end of the water 
drain hose is in a 
position  too low 
according to the 
machine. Place the water  drain 
hose in an appropriate 
height.(**) 
No water is seen in the 
drum during washing. No failure. The water is 
at the lower part of the 
drum. - 
There are residues of 
detergent on the 
clothes. The pieces of some 
detergents which do 
not dissolve in water 
may stick to your 
clothes as white stains. By calibrating your 
machine for “Rinsing” 
program,make an 
additional rinsing or 
eliminate the stains 
After drying with the 
help of a brush. 
There are gray stains 
on the clothes. These stains may be 
caused by oil,cream or 
ointment .  In the next washing 
operation, use the 
maximum detergent 
amount declared by 
the detergent producer. 
 
 
(**)   See the section concerning instalations your machine. 
 
 
 23 
 
						

							 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
FAILURE PROBABLE CAUSE METHODS OF 
ELIMINATION 
The spining process is 
not done or  starts with 
delay . No failure. The 
unbalanced load 
control may works in 
that way. The unbalanced load 
control system will try 
to distribute your 
clothes in a 
homogenous manner. 
After your clothes are 
distributed, passage to 
spining process will be 
realized.In the next 
washing process,place 
your clothes into the 
machine in a well-
balanced manner. 
 
 
SECTION 9: AUTOMATIC FAILURE DETECTION SYSTEM 
 
Your machine is equipped with systems which will both take the necessary 
precautions and warn you in case of any failure by controlling it self constantly 
during the washing processes. 
 
 
FAILURE 
CODE FAILURE 
INDICATOR PROBABLE 
FAILURE THE PROCESS 
TO BE DONE 
Err 01 The start/pause 
light blinks. The door is not 
shut properly. Shut the door 
properly so that 
you hear the 
click. If the 
problem 
persists, turn off 
the machine 
unplug and 
apply to the 
nearest 
authorized 
service 
immediately.  
 
 
 
 24 
 
						

							 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
FAILURE 
CODE FAILURE 
INDICATOR PROBABLE 
FAILURE THE PROCESS 
TO BE DONE 
Err 02 The program 
ready light 
blinks. The water level 
in your machine 
is below heater. 
The pressure of 
your water 
supply may be 
low or locking. Turn on the tap 
to the end.Water 
may be cut, 
check it.If the 
problem is still 
continuing,your 
machine will 
automatically 
stop after a 
while.Unplug 
your machine, 
turn off the tap 
and apply to the 
nearest 
authorized 
service. 
Err 03 The start/pause 
light and 
program ready 
light blinks . The pump has 
failed or the 
pump filter is 
obstructed. Clean the pump 
filter.If the 
problem 
persists,apply to 
the nearest 
authorized 
service.(*) 
Err 04 The program 
end light blinks . Communication 
error Shut down your 
machine and 
unplug. Turn off 
your tap and apply 
to the nearest 
authorized service. 
 
 
 (*)  See the section regarding the maintenance and cleaning of your 
machine. 
 
 
 25 
 
						

							 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
FAILURE 
CODE FAILURE 
INDICATOR PROBABLE 
FAILURE THE PROCESS 
TO BE DONE 
Err 05 The start/pause 
light and program 
end light blink. The heater of your 
machine or the 
heat sensor has 
failed. Shut down your 
machine and 
unplug. Turn off 
your tap and apply 
to the nearest 
authorized service. 
Err 06 The program 
ready light and 
program end light 
blink. The motor has 
failed. Shut down your 
machine and 
unplug. Turn off 
the tap and apply 
to the nearest 
authorized service. 
Err 07 The program 
start/pause light, 
ready light and 
program end light 
stays on 
permanently. Configuration 
error. Shut down your 
machine and 
unplug. Turn off 
the tap and apply 
to the nearest 
authorized service. 
Err 08 The start/pause 
light,program 
ready light and 
program end light 
blink. Fault error Shut down your 
machine and 
unplug. Turn off 
the tap and apply 
to the nearest 
authorized service. 
Err 09 The program 
ready light and 
program end light 
stays on 
permanently. The network 
voltage is too high 
or too low. If the network 
voltage is lower 
than 150V or 
higher than 260V, 
your machine will 
automatically stop. 
When the network 
voltage is 
recovered, your 
machine will 
continue its 
operation. 
 
 
 26 
 
						

							 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
SECTION 10: INTERNATIONAL WASHING SIGNS
 
 
 
     
Washing 
temparature. Do not wash 
(hand wash) Lukewarm iron.  Medium hot iron. 
 
 
 
     
Hot iron.  Do not iron. Do not tumble 
dry. Hang to dry. 
 
 
 
     
Drip dry.  Dry flat.  Do not bleach.  Handy to bleach. 
 
 
 
   
All of these are dry cleaning symbols. The letters are 
to instruct the cleaner what type of solvent to be used. 
Garments bearing these symbols should not be 
washed in your machine unless the label says 
otherwise.  
  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
52012070 
 27