Zanussi Zwf 1431 S Manual

Symptom Possible causes
21 21
Spinning starts late or the machine
does not spin●The electronic unbalance detection device has cut in because the
laundry is not  evenly distributed  in the drum. The laundry is
redistributed by reverse rotation of the drum. This may happen several
times before the unbalance disappears and normal spinning can resume.
If, after 6 minutes, the laundry is still not evenly distributed in the
drum, the machine will not spin. In this case, redistribute the load
manually and...

22 22
Guarantee Conditions
Standard guarantee conditions
We, Zanussi Electrolux, undertake that if, within 12
months of the date of the purchase, this ZANUSSI
ELECTROLUX appliance or any part thereof is proved
to be defective by reason only of faulty workmanship or
materials, we will, at our option repair or replace the
same FREE OF ANY CHARGE for labour, materials or
carriage on condition that:
●The appliance has been correctly installed and used
only on the electricity supply stated on the rating...

23
Installation Instructions
Technical Specifications
It is dangerous to alter the specifications or
attempt to modify this product in any way.
Care must be taken to ensure that the appliance
does not stand on the electrical supply cable.
DIMENSIONS Height 85 cm
Width 60 cm
Depth 62.5 cm
POWER SUPPLY VOLTAGE  230-240 V/50 Hz
TOTAL POWER ABSORBED  2050 W (10A)
WATER PRESSURE  Minimum  0.05 MPa (0.5 bar)
Maximum 0.80MPa (8. bar)
MAXIMUM RECOMMENDED LOAD  Cotton, linen  6.0 kg
Synthetics 2,5 kg
Delicate...

24 24
Unpacking
The transport safeguard must be removed before
putting the appliance into operation.
Important !
You are advised to keep all the packaging for re-use in
case the machine is to be transported again. 
●After removing all the packaging, with assistance
carefully lay machine on it’s back to remove the
polystyrene base from the bottom.
●Remove the power supply cable and the draining hose
from the hose holders on the rear of the appliance.
●With a suitable spanner unscrew and remove the
central...

25
Water inlet
An inlet hose is supplied and can been found inside the
machine drum.
Do not use the hose from your previous machine to
connect to the water supply. 
1. Open the porthole and extract the inlet hose .
2. Connect the hose with the angled connection to the
machine.
Important!
Do not place the inlet hose downwards. Angle the
hose to the left or right depending on the position of
your water tap. 
3. Set the hose correctly by loosening the ring nut. After
positioning the inlet hose, be sure to...

26 If your drain hose looks like this (see below) you do not
require the “U” piece”. Just push the hose firmly into
the standpipe.
2.  Onto a sink outlet spigot.
If the outlet spigot has not been used before, remove
any blanking plug that may be in place.
Push the drain hose onto the spigot and secure with a
clip if required, ensure a loop is formed in the drain
hose (see diagram) to prevent waste from the sink
entering the washing machine.
Important
Before connecting up the machine to new pipework or
to...

27 27 If you require any further advice please contact your
local water authority.
Electrical connection
Any electrical work required to install this appliance
should be carried out by a qualified electrician or
competent person.
WARNING: THIS APPLIANCE MUST BE
EARTHED.
The manufacturer declines any liability should
this safety measure not be observed.
Before switching on, make sure the electricity supply
voltage is the same as that indicated on the appliance’s
rating plate. The rating plate is located...

© Electrolux plc 2006
From the Electrolux Group.The world’s No. 1 choice.
The Electrolux Group is the worlds largest producer of powered appliances for kitchen, cleaning and outdoor use.
More than 55 million Electrolux Group products (such as refrigerators, cookers, washing machines, vacuum
cleaners, chain saws and lawn mowers) are sold each year to a value of approx. USD 14 billion in more than 150
countries around the world.