Zanussi Zwf 1000 M User Manual

Load the laundry
Measure out the detergent and the fabric softener
Select the required programme by means of the
programme selector dial (1)
Turn the selector dial to position to reset the
programme or to switch the machine off.
Important!
Select the spin speed or the Rinse Hold option by
pressing button 2 (only for ZWF1000M)Open the door by
carefully pulling the door
handle outwards. Place
the laundry in the drum,
one item at a time,
shaking them out as much
as possible. Close the
door.
Pull out the...

Cancelling a programme
Turn the selector dial to to cancel a programme
which is running, and wait few minutes to open the
door (This is only possible if there is no water in the
tub).
By pressing any button the appliance will come out of
the energy saving status.O
O
At the end of the programme
Stand-By: The machine stops automatically.
At the end of the programme, the door is released,
after few minutes, and can be opened. Turn the
programme selector dial to to switch the machine
off.
Remove the laundry...

Care and cleaning
ZANUSSI
13
Warning!
Descaling
External cleaning
Cleaning the dispenser drawer
Cleaning the drawer recess You must DISCONNECT the appliance
from the electricity supply, before you can carry
out any cleaning or maintenance work.
The water we use normally contains lime. It is a good
idea to periodically use a water softening powder in
the machine.
Do this separately from any laundry washing, and
according to the softening powder manufacturers
instructions.
This will help to prevent the...

14
If you wash rugs, it is compulsory to inspect and
clean the filter.
Cleaning the water inlet filters
Important!
If the appliance doesnt fill, takes too long to fill with
water, the start button blinks yellow or the display (if
available) shows the relevant alarm (see chapter
«What to do if...» for more details), check if the water
inlet filters are blocked.
To clean the water inlet filters: Turn off the water tap.
 Unscrew the hose
from the tap.
 Clean the filter in the
hose with a stiff brush....

15
ZANUSSI
What to do if.....
Certain problems are due to lack of simple
maintenance or oversights, which can be solved
easily without calling out an engineer.Before contacting your local Service Centre, please
carry out the checks listed below.
MalfunctionPossible Cause / Solution
The washing  machine does not work Close the washing machines door.
Water leakage
Correctly connect  the inlet  water pipe.
The spin of the clothes  is abnormalReload  and distribute the laundry evenly in the drum.
There is a...

16
MalfunctionPossible Cause / Solution
The machine stops when the proce-
dure has not been finishedPower  failure or water cut.
The water inside the inner barrel  has been drained
but there is still a small amount of water in the
drainage pump and pipe. The drainage pump
continuously work and takes in the air, then  there
wil be noise which is normal situation.
The machine stops for some time
during the wash procedure.
The washing machine adds water automatically.
There is too much foam the in drain...

If the washing machine cannot work normally, a alarm code will appear on the display. Please carry
out  the following checks.
Alarm codes
ZANUSSI
Alarm
Code
Status of
Corresponding
Indicators
Wash RinseSpin
Off
Off
FlashDoor lock
problem
Door is not closed properly.
Restart after the door is closed
ReasonSolution
Description
Please call the service number if you experience any
problems.
Off
Flash
Off
Off
Flash
Flash
Off
Flash
On
Excessive
Foam
Drain problem
while washing(drain time
exceeds 7 minutes)...

ZANUSSI
If you are unable to identify or solve the problem,
contact our service centre. Before telephoning, make
a note of the product number, model, serial number
and purchase date of your machine. The Service
Centre will require this information.
Technical data
60kg
2 00W 1 2 00W
160kg
520520
5
7 10
ZWF180M ZWF1000M
 

Installation
Unpacking
Positioning All transit bolts and packing must be removed before
using the appliance.
You are advised to keep all transit devices so that
they can be refitted if the machine ever has to be
transported again.Unscrew the four boltsusing a spanner.
Slide out the relevant
plastic spacers.
Fill the holes with the
corresponding plastic
plug caps supplied in the
bag containing the
instruction booklet.
Install the machine on a flat hard floor. Make sure that air
circulation around the...

ZANUSSI
Caution!
Water drainageHooked over the edge
of a sink
The inlet hose must not be lengthened. If it
is too short and you do not wish to move the tap, you
will have to purchase a new, longer hose specially
designed for this type of use.
The end of the drain hose can be positioned in three
ways:
using the
plastic hose guide
supplied with the
machine.
In this case, make sure
the end cannot come
unhooked when the
machine is emptying.
This could be done by
tying it to the tap with a piece of string or...