Zanussi Zwf 1000 M User Manual

							
Load the laundry
Measure out the detergent and the fabric softener
Select the required programme by means of the
programme selector dial (1)
Turn the selector dial to position to reset the
programme or to switch the machine off.
Important!
Select the spin speed or the Rinse Hold option by
pressing button 2 (only for ZWF1000M)Open the door by
carefully pulling the door
handle outwards. Place
the laundry in the drum,
one item at a time,
shaking them out as much
as possible. Close the
door.
Pull out the dispenser drawer until it stops. Measure
out the amount of detergent required, pour it into the
main wash compartment or in the appropriate
compartment if the selected programme/option it
requires (see more details in «Detergent dispenser
drawer»).
If required, pour fabric softener into the compartment
marked (the amount used must not exceed the
«MAX» mark in the drawer). Close the drawer gently.
Turn the programme selector dial to the required
programme.
The selector dial can be turned either clockwise or
anticlockwise.
At the end of the programme the selector dial must be
turned to position , to switch the machine off. If you turn the programme selector dial to
another programme when the machine is working, the
machine will not perform the new selected
programme.
When selecting a programme, the appliance
proposes automatically a suggested spin speed for
that programme. (See «Washing programmes» for
the maximum allowed spin speed).
Press this button repeatedly to change the spin
speed, if you want your laundry to be spun at a
different speed. The relevant pilot light illuminates. O
O
Daily Use
Select the available options by pressing button 2
for the model ZWF180M and buttons 3 for model
the ZWF1000M
Select the Prewash option by pressing button 3
for the model ZWF180M and button 4 for the
model ZWF1000M.
Start the programme by pressing button 5 for
model the ZWF180M and button 6 for the model
ZWF1000M When this button is pressed, the corresponding pilot
light illuminates. When it is pressed again, the pilot
light goes out.
to start the selected washing
programme. When this button is pressed, the corresponding pilot
light illuminates. When it is pressed again, the pilot
light goes out.
Press this button
It is possible to change some options before the
programme carries them out.
Before you make any change, you must pause the
washing machine by pressing button for ZWF180M
or for ZWF1000M.
To change a running programme:
urn the programme selector dial to select the
new programme and tart the new programme;
The washing water in the tub will be emptied out. .
Press the button for ZWF180M or for ZWF1000M.
to interrupt a programme which is running.
Press the button again to restart the programme. Altering an option
5
6
Change a running programme
Warning!
Interrupting a programme 56

press button for ZWF180M
or for ZWF1000M to s
 press button for ZWF180M or for ZWF1000M to pause the machine, turn the programme selector
dial to the new programme and press button or
again. O,
5
6 56
56
For safety reasons you are only able to
change the programme before the heating phase has
started
11
ZANUSSI
 
						

							
Cancelling a programme
Turn the selector dial to to cancel a programme
which is running, and wait few minutes to open the
door (This is only possible if there is no water in the
tub).
By pressing any button the appliance will come out of
the energy saving status.O
O
At the end of the programme
Stand-By: The machine stops automatically.
At the end of the programme, the door is released,
after few minutes, and can be opened. Turn the
programme selector dial to to switch the machine
off.
Remove the laundry from the drum and carefully
check that the drum is empty. If you do not intend to
carry out another wash, close the water tap. Leave
the door open to prevent the formation of mildew and
unpleasant smells.
Once the programme has finished after a few minutes
the energy saving system will be enabled.
12
 
						

							
Care and cleaning
ZANUSSI
13
Warning!
Descaling
External cleaning
Cleaning the dispenser drawer
Cleaning the drawer recess You must DISCONNECT the appliance
from the electricity supply, before you can carry
out any cleaning or maintenance work.
The water we use normally contains lime. It is a good
idea to periodically use a water softening powder in
the machine.
Do this separately from any laundry washing, and
according to the softening powder manufacturers
instructions.
This will help to prevent the formation of lime
deposits.
Clean the exterior cabinet of the appliance with soap
and water only, and then dry thoroughly.
The washing powder and additive dispenser drawer
should be cleaned regularly.
Flush it out under a tap, to remove any traces of
accumulated powder.
Havin g removed the drawer, use a small brush to
clean the recess ensuring
that all washing powder
residue is removed from
the upper and lower part
of the recess.
Replace the drawer and
run the rinse programme without any clothes in the
drum. Cleaning the pump
Important!
Warning!
According to the soil level within the cycles and the
frequency of the cycles, you have to inspect and
clean the filter regularly.
The pump should be inspected if:
 the machine does not empty and/or spin;
 the machine makes an unusual noise during
draining due to objects such as safety pins, coins
etc. blocking the pump.
Proceed as follows:
1 disconnect the appliance;
2 if necessary wait until the water has cooled down.
3 Open the pumpdoor. Place a container
close to the pump to
collect any spillage.
4 Gradually unscrew the pump cover to drain out the water.
When no more water comes out, unscrew the pump cover and remove it. Always keep a towel
nearby to dry up spillage of water when removing
the cover.
6 Remove any objects from the pump impeller by rotating it.
7 Screw the pump cover fully in.
8 Close the pump door.
When the appliance is in use and depending on the
programme selected there can be hot water in the
pump. Never remove the pump cover during a wash
cycle, always wait until the appliance has finished the
cycle, and is empty. When replacing the cover, ensure
it is securely retightened so as to stop leaks and
young children being able to remove it. 5
Clean
3
1
Press
Pull out at the same time
2
Pump cover
 
						

							
14
If you wash rugs, it is compulsory to inspect and
clean the filter.
Cleaning the water inlet filters
Important!
If the appliance doesnt fill, takes too long to fill with
water, the start button blinks yellow or the display (if
available) shows the relevant alarm (see chapter
«What to do if...» for more details), check if the water
inlet filters are blocked.
To clean the water inlet filters: Turn off the water tap.
 Unscrew the hose
from the tap.
 Clean the filter in the
hose with a stiff brush.
 Screw the hose back onto the tap. Make sure the
connection is tight.
 Unscrew the hose from the machine. Keep a rag
nearby because some water may flow.
 Clean the filter in the valve with a stiff brush or with
the piece of cloth.
 Screw the hose back to the machine and make sure
the connection is tight.
 Turn on the water tap. Frost precaution or emergency emptied out
If the machine is exposed to temperatures below 0°C
or if the water is not discharged, proceed as follows.
1 Pull out the plug from the power socket.
2 Turn off the water tap.
3 Unscrew the inlet hose.
4 Place a bowl on the floor and place the end of the
inlet and drain hoses into it. The water should drain
by gravity into the bowl.
5 Select and run a draining programme.
6 Clean the pump if necessary as previously described.
7 Screw the water inlet hose back on.
8 When you intend to start the machine up again, make sure that the room temperature is above
0°C.
 
						

							
15
ZANUSSI
What to do if.....
Certain problems are due to lack of simple
maintenance or oversights, which can be solved
easily without calling out an engineer.Before contacting your local Service Centre, please
carry out the checks listed below.
MalfunctionPossible Cause / Solution
The washing  machine does not work Close the washing machines door.
Water leakage
Correctly connect  the inlet  water pipe.
The spin of the clothes  is abnormalReload  and distribute the laundry evenly in the drum.
There is a peculiar  smell in the wa-
shing machineRun a washing cycle without any clothes at maximum
temperature using a biological powder.
No water is visible in the drum
No fault-water is under the visible area.
There is the remaining  water in the
softeners  boxNo fault the effect of the softener will not be affected.
Empty before next use.
The remaining  detergent is left  onthe clothes
The washing machine does not fill
Turn on the water tap.
Check the selection of . the  procedure
Reconnect the water inlet pipe. Check if  the water pressure  is sufficient.
Check if the inlet water pipe is bent or blocked.
Close the  washing machine’s door.
The washing machine fills and drains
at  the same time.
Make sure the end  of the drainage pipe is higher
than the water level  inside the machine .
Please delete or amend this sentence we would not
recommend for anyone to seal their drainage pipe.
The washing machine does not drain
Check if the drainage pumps is blocked.
Check if the drainage pipe is bent or  blocked.
Check the height of the drainage nozzle, make
sure it is 0.6-1 meter high from the bottom of the
washing machine.
Vibration of the washing  machine
Level  the washing machine.
Fasten the footing.
Check if all the delivery bolts have all  been removed. Press the S button. tart/Pause
The water-fast  component of the non-phosphorus
detergent will be left on the clothes to form into spot. Please select «Rinse&Spin» programme.
or brush away the  fleck after the clothes is dried.
 
						

							
16
MalfunctionPossible Cause / Solution
The machine stops when the proce-
dure has not been finishedPower  failure or water cut.
The water inside the inner barrel  has been drained
but there is still a small amount of water in the
drainage pump and pipe. The drainage pump
continuously work and takes in the air, then  there
wil be noise which is normal situation.
The machine stops for some time
during the wash procedure.
The washing machine adds water automatically.
There is too much foam the in drain tube, the foam is
being drained.
Foam spills from the detergent
drawer
Check if the amount of detergent is excessive,
if  it is the specialized detergent for the drum
washing machine.
Reduce the amount of detergent used next time. Dip one scoop of the softener mixed with 1/2 liter
of water to  the detergent box II.
The drainage pump is noisy during
operation after the water has been
drained.
 
						

							
If the washing machine cannot work normally, a alarm code will appear on the display. Please carry
out  the following checks.
Alarm codes
ZANUSSI
Alarm
Code
Status of
Corresponding
Indicators
Wash RinseSpin
Off
Off
FlashDoor lock
problem
Door is not closed properly.
Restart after the door is closed
ReasonSolution
Description
Please call the service number if you experience any
problems.
Off
Flash
Off
Off
Flash
Flash
Off
Flash
On
Excessive
Foam
Drain problem
while washing(drain time
exceeds 7 minutes)
Water fill problem
when washing
(water fill time
exceeds 5
minutes)Tap is not opened or water flows too slowly.
Inlet valve filter is blocked.
Inlet pipe is twisted.
If water is not supplied Open the tap or wait till
the water supply
becomes normal.
Check inlet valve filter.
Straighten the water pipe
Check the other taps in
the room.
Outlet hose is blocked or twisted
Drain pump is blocked Wash and straighten outlet
hose.
Wash drain pump filter
Please call up the service line if there is any other problem.
Excessive detergent has
been used.  Wrong detergent used.
Detergent used improperly.Reduce detergent quantity
Use the detergents suitable
for washing machine
Please call the service number if you experience any
problems.
Please call the service number if you experience any
problems.
Please call the service number if you experience any
problems.
17
 
						

							
ZANUSSI
If you are unable to identify or solve the problem,
contact our service centre. Before telephoning, make
a note of the product number, model, serial number
and purchase date of your machine. The Service
Centre will require this information.
Technical data
60kg
2 00W 1 2 00W
160kg
520520
5
7 10
ZWF180M ZWF1000M
 
						

							
Installation
Unpacking
Positioning All transit bolts and packing must be removed before
using the appliance.
You are advised to keep all transit devices so that
they can be refitted if the machine ever has to be
transported again.Unscrew the four boltsusing a spanner.
Slide out the relevant
plastic spacers.
Fill the holes with the
corresponding plastic
plug caps supplied in the
bag containing the
instruction booklet.
Install the machine on a flat hard floor. Make sure that air
circulation around the machine
is not impeded by carpets, rugs
etc. Check that the machine
does not touch the wall or other
kitchen units. Level the
washing machine by raising or
lowering the feet. The feet may
be tight to adjust as they
incorporate a self locking nut,
but the machine MUST be level and stable.
Any necessary adjustment can be made with a
spanner.
If necessary, check thesetting with a spirit level. Accurate levelling prevents vibration, noise and
displacement of the machine during operation. Never
place cardboard, wood or similar materials under the
machine to compensate for any unevenness in the
floor.
This appliance must be connected to a
cold water supply.
Before connecting up the appliance to
new pipework or to pipework that has not been
used for some time, run off a reasonable amount of
water to flush out any debris that may have collected
Do not use the hose from your previous
appliance to connect to water supply.
Connect the hose to a tap
with a 3/4” thread.Always use the hose
supplied with the
appliance.
The other end of the inlet hose which connects to the
appliance can be turned as showed in the picture. Do
not place the inlet hose downwards. Angle the hose to
the left or right depending on the position of your
water tap. Set the hose correctly by loosening the ring
nut. After positioning the inlet hose, be sure to tighten
the ring nut again to prevent leaks. Water inlet Caution!
Caution!
Caution!
1
2
19
 
						

							
ZANUSSI
Caution!
Water drainageHooked over the edge
of a sink
The inlet hose must not be lengthened. If it
is too short and you do not wish to move the tap, you
will have to purchase a new, longer hose specially
designed for this type of use.
The end of the drain hose can be positioned in three
ways:
using the
plastic hose guide
supplied with the
machine.
In this case, make sure
the end cannot come
unhooked when the
machine is emptying.
This could be done by
tying it to the tap with a piece of string or attaching it
to the wall.
In a sink drain pipe branch
Caution!
Directly into a drain pipe .
This branch must be above the trap so that the bend
is at least 60 cm above the ground.
This must be secured with a clip. at a height of not less than
60 cm and not more than 90 cm. The end of the drain
hose must always be ventilated , i.e. the inside
diameter of the drain pipe must be larger than the
outside diameter of the drain hose.
Electrical connection
Environment concerns
Information on the electrical connection is given on
the rating plate on the inner edge of the appliance
door. Check that your domestic electrical installation
can take the maximum load required, also taking into account any other appliances in use.
Connect the machine to an earthed
socket.
The manufacturer does not accept any
responsibility for damage or injury through failure
to comply with the above safety precaution. Caution!
Caution!
The symbol on the product or on its packaging
indicates that this product may not be treated as
household waste. Instead it should be taken to the
appropriate collection point for the recycling of
electrical and electronic equipment. By ensuring this
product is disposed of correctly, you will help prevent
potential negative consequences for the environment
and human health, which could otherwise be caused
by inappropriate waste handling of this product. Caution!
Should the appliance power supply
cable need to be replaced, this MUST be carried
out by a Service Centre.
The power supply cable must be easily accessible
after installing the machine.
For more detailed information about recycling of this
product, please contact your local council, your
household waste disposal service or the shop where
you purchased the product.
The materials marked with the symbol are recyclable.
>