Zanussi Zrb 834 Nw User Manual

							8. Open the door. Make sure that the light comes on.
21
3
Closing the door
1. Clean the door gaskets.
2. If necessary, adjust the door. Refer to Installation.
3. If necessary, replace the defective door gaskets.
Contact the Service Force Center.
Technical data
   
Dimension  
 Height1850 mm
 Width595 mm
 Depth632 mm
Rising Time 18 h
The technical information are situated in the rating plate
on the internal left side of the appliance and in the en-
ergy label.
Installation
Caution!  Read the Safety Information carefully
for your safety and correct operation of the
appliance before installing the appliance.
Positioning
Install this appliance at a location where the ambient
temperature corresponds to the climate class indicated
on the rating plate of the appliance:
Climate
classAmbient temperature
SN+10°C to + 32°C
N+16°C to + 32°C
ST+16°C to + 38°C
T+16°C to + 43°C
Location
The appliance should be installed well away from sour-
ces of heat such as radiators, boilers, direct sunlight
etc. Ensure that air can circulate freely around the back
of the cabinet. To ensure best performance, if the ap-
pliance is positioned below an overhanging wall unit,
the minimum distance between the top of the cabinet
and the wall unit must be at least 100 mm . Ideally,
however, the appliance should not be positioned below
overhanging wall units. Accurate levelling is ensured
by one or more adjustable feet at the base of the cab-
inet.
Warning!  It must be possible to disconnect the
appliance from the mains power supply; the plug
must therefore be easily accessible after installation.
AB
min.100 mm 20 mm
 11
 
						

							Electrical Connection
Caution!  Any electrical work required to install
this appliance should be carried out by a qualified
electrician or competent person.
Warning!  This appliance must be earthed.
The manufacturer declines any liability should
these safety measures not be observed.
12
3
4
5
Important!  The wires in the mains lead are coloured
in accordance with the following code:
1Green and Yellow: Earth
3Brown: Live
5Blue: Neutral
As the colours of the wires in the mains lead of this
appliance may not correspond with the coloured mark-
ings identifying the terminals in your plug, proceed as
follows:
1. Connect the wire coloured green and yellow to the
terminal marked either with the letter “E“ or by the
earth symbol 
 or coloured green and yellow.
2. Connect the wire coloured blue to the terminal ei-
ther marked with the letter “N“ or coloured black.
3. Connect the wire coloured brown to the terminal
either marked with the “L“ or coloured red.
4. Check that no cut, or stray strands of wire is present
and the cord clamp 
4 is secure over the outer
sheath.
5. Make sure the electricity supply voltage is the same
as that indicated on the appliance rating plate.
6. Switch on the appliance.
The appliance is supplied with a 13 amp plug fitted
2 . In the event of having to change the fuse in the
plug supplied, a 13 amp ASTA approved (BS 1362)
fuse must be used.
Warning!  A cut off plug inserted into a 13 amp
socket is a serious safety (shock) hazard. Ensure
that it is disposed of safely.
Rear spacers and levelling
12
3
In the bag with the docu-
mentation, there are two
spacers which must be
fitted as shown in the fig-
ure.
Slacken the screws and
insert the spacer under
the screw head, then
tighten again the screws.When placing the appli-
ance ensure that it
stands level. This can be
achieved by two adjusta-
ble feet at the bottom in
front.
Removing the shelf holders
Your appliance is equipped with shelf retainers that
make it possible to secure the shelves during trans-
portation.
To remove them proceed as follows:
1. Move the shelf holders in the direction of the arrow
(A).
12
 
 
						

							2. Raise the shelf from the rear and push it forward
until it is freed (B).
3. Remove the retainers (C).
Door reversibility
Warning!  Before carrying out any operations,
remove the plug from the power socket.
Important!  To carry out the following operations, we
suggest that this be made with another person that will
keep a firm hold on the doors of the appliance during
the operations.
m3m4
m5
m1
m2
1
• Open the doors. Un-
screw the middle hinge
(m2). Remove the plas-
tic spacer (m1).
• Remove the doors.
• Remove the left-hand
cover pin of the middle
hinge (m3,m4) and
move to the other side.
• Fit the pin of the middle
hinge (m5) into the left-
hand hole of the lower
door.• Unscrew the lover
hinge (b1)
• Remove the left-hand
cover pins (b4) and
move to the other side.
• Re-screw the lover
hinge (b1) on the oppo-
site side.
• Unscrew the lower
hinge pivot (b2) and the
spacer (b3) and place
them on the opposite
side.• Remove the plugs (1)
on the upper side of
both doors and move
them to the other side.
• Re-insert the the lower
door on the lower hinge
pivot (b2).
• Insert the middle hinge
(m2) into the left drill of
the lower door.• Unscrew the upper
hinge pivot and place it
on the opposite side.
• Fit the upper door on
the upper door pivot.
• Re-insert the upper
door on the middle
hinge pivot (m5) slight-
ly tilting both doors.
• Re-screw the middle
hinge (m2). Do not for-
get the plastic spacer
(m1).
Do a final check to make sure that:
• All screws are tightened.
• The edges of the doors run parallel to the side edge
of the appliance.
• The magnetic seal adheres to the cabinet.
• The door opens and closes correctly.
If the ambient temperature is cold (i.e. in Winter), the
gasket may not fit perfectly to the cabinet. In that case,
wait for the natural fitting of the gasket or accelerate
this process by heating up the part involved with a nor-
mal hair drier.
In case you do not want to carry out the above men-
tioned operations, contact the nearest After Sales Serv-
ice Force. The After Sales Service specialist will carry
out the reversibility of the doors at your cost.
Environmental concerns
The symbol    on the product or on its packaging
indicates that this product may not be treated as
household waste. Instead it should be taken to the
appropriate collection point for the recycling of
electrical and electronic equipment. By ensuring this
product is disposed of correctly, you will help preventpotential negative consequences for the environment
and human health, which could otherwise be caused
by inappropriate waste handling of this product. For
more detailed information about recycling of this
product, please contact your local council, your
 13
 
						

							household waste disposal service or the shop where
you purchased the product.
14
 
 
						

							 15
 
						

							www.electrolux.com
925033610-00-02102008
925033610