Zanussi Rubino 2 1200 Manual

69 Ball point pen and glue: moisten with acetone (*),
lay the garment on a soft cloth and dab the stain.
Lipstick: moisten with acetone as above, then treat
stains with methylated spirits. Remove any residual
marks from white fabrics with bleach.
Red wine: soak in water and detergent, rinse and
treat with acetic or citric acid, then rinse. Treat any
residual marks with bleach.
Ink: depending on the type of ink, moisten the fabric
first with acetone (*), then with acetic acid; treat any
residual marks on...

70
ENGLISH
International wash code symbols
These symbols appear on fabric labels, in order to help you choose the best way to treat your laundry.
Energetic wash
Delicate washMax. wash
temperature
95°CMax. wash
temperature
60°CMax. wash
temperature
40°CMax. wash
temperature
30°C
Hand wash Do not
wash
at all
BleachingBleach in cold water Do not bleach
IroningHot iron
max 200°CWarm iron
max 150°CLukewarm iron
max 110°CDo not iron
Dry cleaningDry cleaning
in all solventsDry cleaning in
perchlorethylene,...

71The lights corresponding to the different phases
making up the selected programme light on.
The light of the START/PAUSE button starts to flash.
5. Select the required options
The light corresponding to the depressed button
illuminates.
6. Start the programme
Depress START/PAUSE-button, the corresponding
pilot light stops flashing. The DOOR light illuminates
and only the pilot light WASHING remains lit.
7. Altering a programme
You can alter the programme before it starts.
When the programme has...

72
ENGLISH
9. Cancelling a programme
Turn the selector dial to Oto cancel a programme
which is running.
Now you can select a new programme.
10. Opening the door after the
programme has started
First set the machine to PAUSE by pressing the
START/PAUSE button.
The door can be opened when the DOOR light has
gone out.
If the door does not open, this means that the water
temperature is above 55°C, that the water level is
above the bottom edge of the door or that the drum
is turning.
If you cannot open the...

73
Programme table
ECONOMY PROGRAMME
For slightly/normally soiled cottons you can use the relevant Economy programme: you will obtain good
washing results by saving energy.
In compliance with EC directive 92/75, the consumption figures indicated on the energy label refer to the 60E
wash programme for cotton.
* The consumption data shown on this chart is to be considered purely indicative, as it may vary depending on
the quantity and type of laundry, on the inlet water temperature and on the ambient...

74
ENGLISH
Programme table
SPECIAL PROGRAMMES
* The consumption data shown on this chart is to be considered purely indicative, as it may vary depending on
the quantity and type of laundry, on the inlet water temperature and on the ambient temperature.
Programme
selector dial
position
Rinses
ProgrammeProgramme
descriptionAdditional
functionsWash load
max.Energy
kWhWater
ltDuration
min. Consumptions*
For rinsing
hand washed
items3 rinses with liquid
additive, if required
Short spin at max.
speed
4.5 kg...

75
1. Bodywork
Clean the outside of the machine with soap and
water only. Rinse with clean water and dry with a
soft cloth.
Important:do not use methylated spirits, solvents
or similar products to clean the bodywork.
2. Door seal
Check from time to time the door seal and eliminate
eventual possible objects that could be trapped in
the fold.
3. Detergent dispenser drawer
After a while, detergents and fabric softeners leave
deposits in the drawer.
Clean the drawer from time to time by rinsing it
under a...

76
ENGLISH
•  Place a bowl on the floor to collect any spillage. 
•  Pull out the emergency emptying hose, place it in
the bowl and remove its cap.
•  When no more water comes out, unscrew the
pump cover and remove it.
•  Remove any objects from the pump impeller by
rotating it.
• Put the cap back on the emergency emptying hose
and place the latter back in its seat.
•  Screw the pump cover fully in.
• Close the pump door.
6. Emergency emptying out
If the water is not discharged, proceed as follows to...

77 Problems which you can resolve yourself, before calling the After Sales Service.
During machine operation it is possible that the END light starts to flash:
4 flashes= the door has not been closed
2 flashes= the machine does not empty
1 flash= the machine does not fill.
On models with buzzer an acoustic signal will be sound.
Once the problem has been eliminated, press the START/PAUSE button to restart the programme. If after all
checks, the problem persists, contact your local Service Centre.
Problem...

78
ENGLISH
If you are unable to identify or solve the problem,
contact our service centre. Before telephoning,
make a note of the model, serial number and
purchase date of your machine: the Service Centre
will require this information.
Mod. ..........
Prod. No. ...........
Ser. No. .........
M
o
d
.
 
.
.
.
.
.
.
.
.
.
.
P
ro
d
.
 
N
o
.
 
.
.
.
.
.
.
.
.
.
.
.
S
e
r.
 
N
o
.
 
.
.
.
.
.
.
.
.
.
P0042 BD
Problem Possible cause
•Water is not visible in the
machine:• The machine, which is the result of...