Yamaha Projector Dpx 1300 User Manual

7
Remote control
4
English
iINPUT button
Switches on and off the input signal selection menu display.
oLIGHT switch
Moving this switch lights the high-use AUTO (2), ESCAPE
(6), ASPECT(8) , 
 (e), MENU (y), and INPUT (i)
buttons. The light disappears if you do not perform any
operation within 10 seconds.
pHIDE button
Temporarily halts projection of the image the DPX-1300 is
currently displaying. Press again to cancel this effect.
aRemote control code switch
Selects ID-1 or ID-2 when operating two main...

8
◆Loading the batteries into the remote control
1. Remove the battery compartment cover.
2. Insert two batteries (AA, UM3, or R6 type), matching the polarity
markings on the batteries with those in the battery
compartment.
3. After loading the batteries, close the cover until it snaps into
place.
Warning
•If the remote control must be used closer to the main unit than normal, or does not always operate correctly, exchange the
batteries for new ones.
•Do not mix old and new, or different types of...

9
Remote control
4
English
Distance to sensor Angle to sensor
7 m 30˚ vertically and horizontally
(approximate value) (approximate value)
◆Limits for using the remote control
Use the remote control within the following parameters. The remote control may not function correctly if you use it outside the limits
described here.
Warning
•Bright or fluorescent light on the main unit remote sensor may inhibit the functioning of the remote control.
•Objects placed between the main unit remote sensor and the...

10
Before projection, install the main unit and a screen, connect the main unit to an AV component or computer, and adjust the projection image.
You can begin projection as soon as installation is complete.
Refer to the sections below for information on how to install the main unit to suit your viewing environment.
◆If you have not installed the main unit or screen
• Immediately after purchase, when you have not installed either the main unit or a screen.
• When moving the main unit and screen to a new...

11
Prepararion
5
English
Step2
Connect an AV component or computer
•Connect AV  components
•Connect a computer  ☞ page 15 - 16
Step3
Turn the power on and selecting an
image for projection
•Turn on the projector power
•Begin playback of the input image
•Select an input signal
•Select a projection image aspect
•Adjust the image
Focus/Vertical and Horizontal position/Size/Iris
☞ page 17 - 26
Step1
Set up the projector and screen
•Install the projector
•Install the screen  ☞ page 12 - 14
Only adjust these...

12
Setting up the DPX-1300
◆Mounting the projector on a table
A: From in front of a screen
Place the unit on a table to project and view the image from in front of the screen. Usually,
place the unit on a reasonably high table. The height from the bottom of the unit to the center
of the lens is 12.4 cm (4”-7/8).
B: From behind a screen (using a semi-translucent screen)
Place the unit on a table to project and view the image from behind a semi-translucent
screen. The distance between the projector and the...

13
Installation
6
English
The most suitable distance between the screen and the projector (see Projection distance [a]) depends on the size of the screen (diagonal
length) you use. You can use the zoom function to adjust the projection distance within a preset range from Wide to Tele. You can also alter
the V.POS parameter to adjust the vertical position of the image to better suit the screen. Use the information in the table below to determine
the best location to place the projector in to suit your...

14
Follow the instructions to adjust the position of the projected image on screen.

This illustration shows the limits within which the
zoom function can alter projection distance [a] in
relation to screen size. You can adjust the image
within these limits so that it fills the screen
completely. ( ☞ page 26)

You can adjust the vertical position of the
projection image up or down by half of the height
of the screen. For example, shifting V.POS fully up
brings the lower limit of the image above the...

15
Connection
7
English
Connecting to AV components
This unit is equipped with 7 types of video input jacks for AV components. Follow the diagram to connect AV components to this unit, taking
care to use cables and adapters that match the input jacks.
Warning
•Be sure to turn off the power of this unit and the source component before attempting connection.
•Connection methods and jack names may differ depending on the component you are attempting to connect. Refer to the owner’s
manual for the...

16
You can use the following three methods to connect to computer devices. Be sure to use cables with jacks that match the connectors and
jacks you wish to use. The HDMI terminal does not support PC signals.
Connecting to computer devices
HDMI DVI
G/Y B/PB/CBR/PR/CR
INPUT A
HD/SYNC
VD
OUT IN
REMOTETRIGGER OUT
S VIDEOVIDEO
INPUT B
RGB/YP
BPR/YCBCR
RS-232C
D4 VIDEO
D-Sub monitor
cableBNC monitor cable
Monitor output terminal
Computer devices
Use the supplied trigger-out DC plug to control external...