Yamaha Projector Dpx 1200 User Manual

7
Remote control
4
iINPUT button
Switches on and off the input signal selection menu display.
oLIGHT switch
Moving this switch lights the high-use AUTO (2), ESCAPE
(6), ASPECT(8) , 
 (e), MENU (y), and INPUT (i)
buttons. The light disappears if you do not perform any
operation within 10 seconds.
pHIDE button
Temporarily halts projection of the image the DPX-1200 is
currently displaying. Press again to cancel this effect.
aRemote control code switch
Selects ID-1 or ID-2 when operating two main units with...

8

Loading the batteries into the remote control
1. Remove the battery compartment cover.
2. Insert two batteries (AA, UM3, or R6 type), matching the polarity
markings on the batteries with those in the battery
compartment.
3. After loading the batteries, close the cover until it snaps into
place.
Warning
•If the remote control must be used closer to the main unit than normal, or does not always operate correctly, exchange the
batteries for new ones.
•Do not mix old and new, or different types of...

9
Remote control
4
Distance to sensor Angle to sensor
7 m 30˚ vertically and horizontally
(approximate value) (approximate value)

Limits for using the remote control
Use the remote control within the following parameters. The remote control may not function correctly if you use it outside the limits
described here.
Warning
•Bright or fluorescent light on the main unit remote sensor may inhibit the functioning of the remote control.
•Objects placed between the main unit remote sensor and the remote...

10
Before projection, install the main unit and a screen, connect the main unit to an AV component or computer, and adjust the projection image.
You can begin projection as soon as installation is complete.
Refer to the sections below for information on how to install the main unit to suit your viewing environment.

If you have not installed the main unit or screen
• Immediately after purchase, when you have not installed either the main unit or a screen.
• When moving the main unit and screen to a new...

11
Prepararion
5
Step2
Connect an AV component or computer
• Connect AV  components
• Connect a computer   page 48
Step3
Turn the power on and selecting an
image for projection
• Turn on the projector power
• Begin playback of the input image
• Select an input signal
• Select a projection image aspect
• Adjust the image
Focus/Vertical and Horizontal position/Size/Iris
 page 12 - 21
Step1
Set up the projector and screen
• Install the projector
• Install the screen   page 50
Only adjust these
parameters...

12
Checking installation and connections

Pre-operation check
Prior to projection, adjust settings to suit the location of the main unit and screen, and the input signal you are using.
However, there is usually no need to adjust any settings if you have not changed the installation location or components since the last time
you used this unit. Check settings and connections only when the unit does not appear to project images correctly.
PHONO
DVRSTANDBY
/ONPURE DIRECT
2CH/MULTI CHSPEAKERSVIDEO AUXREC...

13
Projection
6 
Turning the power on
Always remove the lens cap before operating the main unit.
Turning the projector power on
1. Insert the supplied power cable
firmly into the AC inlet at the rear
of the main unit, then insert the
plug into an AC outlet.
The STANDBY/ON indicator lights orange.
2. Press the STANDBY/ON button
(the 
 button on the remote
control).
The indicator blinks green and the lamp
lights up in preparation for projection. After
approximately 35 seconds, the indicator
changes from...

14
1. Press the STANDBY/ON button.
A confirmation message appears on the
screen.

Placing the DPX-1200 in standby mode
2. If you wish to place the DPX-1200
in standby mode, press the
STANDBY/ON button again.
The lamp changes to a half lit state, and the
fan activates for 2 minutes to cool the lamp.
During this time, the STANDBY/ON
indicator blinks orange, and pressing
STANDBY/ON does not turn main unit
power on again. When the unit finishes
cooling, the fan stops, and the STANDBY/
ON indicator turns...

15
Projection
6 
Selecting using the INPUT button
Press the INPUT button to select an input signal from a source component. Choose from the following:
Projection image signal
Selecting an input signal
Selects component video signals received from AV components connected to the VIDEO jack.
Selects S-Video signals received from AV components connected to the S VIDEO jack.
• Component : Selects component signals received from the INPUT A BNC jacks.
• RGB PC : Selects RGB signals received from computers...

16

Selecting an input signal
1. Press the INPUT button.
The input signal selection menu appears on
the display.
4. Select an appropriate setting
from  [Component], [RGB PC], or
[RGB TV] and press the 
 button
to confirm the setting. 3. Press the + button to open the
submenu. 2. Use the h or g buttons to select
an input signal, then press the  
button.
The 
 mark to the right of the input signal
name indicates that there is a submenu
available for selection.
Input signal
VIDEO
S VIDEO
INPUT A
INPUT B...