Yamaha Projector Dpx 1200 User Manual

17
Projection
6
Selecting an input signal
1. Press the ASPECT button.
The display aspect selection menu appears
on the display.

Selecting a display aspect for a projection image
The display aspect parameter sets the ratio of height to width the unit uses to project an image for an input signal.
Memo
•The display aspect you can use depends on the current input signal. When the input
signal contains display aspect information, set the display aspect parameter to
[Auto] to detect the appropriate display...

18

Memo
•Refer to the glossary for explanations of terms such “letterbox” or “squeeze”. ( page 53)
Auto
Detects information encoded in letterbox or squeeze type input
signals and automatically selects an appropriate display aspect.
Depending on the input source, the unit may not change to the
most appropriate mode. In this case, manually select a suitable
setting.
Normal
Projects images with their original display aspect. Depending
on the input signal, black areas may appear to the left and right
of...

19
Projection
6
Selecting an input signal

Input signal type
Standard 4:3 image
Letter box
Squeeze
14:9 image
HDMI
RGB PC
All
Display aspect Input image Projected image
SUBTITLE
Normal
Cinema
Scope
Normal
Squeeze
Normal
Smart Zoom
Zoom
Subtitle Zoom
Cinema Zoom
Squeeze
Squeeze
Cinema Squeeze
 14:9 Zoom
Normal
Cinema Zoom
Normal
Normal Through
Squeeze Through
12_DPX-1100_E.p6511/26/04, 1:47 PM 19 

20
Select an image for projection
Carry out the following adjustments to obtain optimal projection conditions.

 Adjusting the vertical position – V.POS  button
If the center of the screen is not in line with the center of the lens of the DPX-1200, use the V.POS button to adjust the position of the image
up or down. You can adjust the image to a maximum of half of the height of the projection screen.
1. Press the V.POS button on the
remote control, or press the
SETTING button on the main unit
repeatedly...

21
Projection
6
Adjusting the image

 Adjusting the size of an image – ZOOM button
Enlarge or reduce the size of the projection image to match the size of the screen. The zoom ratio is 1:1.6.
1. Press the ZOOM button on the
remote control, or press the
SETTING button on the main unit
repeatedly to select [Zoom] from
the display menu.
2. Press the h or g button to adjust
the image to a suitable size.
3. To exit from the adjustment
mode, press the ZOOM or
ESCAPE buttons.

 Adjusting the image focus – FOCUS...

22
Off                         LMLMHH
abcde
VIDEO 0
0
0100
46000K +
0.005uv0
Image
Black Level
Off
Memory 1 White Level
Gamma Trim
Hue
Saturation
Sharpness Type
Sharpness Gain
Level Adjustment IrisSignal Initial Setup
Standard Move Menu Window
Color Adjustment
White Peaking
VIDEO+ : Enter
Image
Memory 1 Signal Initial SetupMove Menu Window
Color AdjustmentStandard 6700K +
0.000uv-
Black Level
OffLMLMHH
abcde 0White Level 0GammaHue 0Saturation 100Sharpness TypeSharpness Gain
Level AdjustmentIris
4
White...

23
Menu
7 
Menu item list:
There are two types of menu, [Basic Mode] and [Advanced Mode].
• Basic mode: The menu displays menu items that are frequently used or absolutely necessary to image projection.
• Advanced mode: The menu displays all menu items, allowing you to carry out detailed adjustments.
You can change between the menu modes using the [Menu Mode] setting in the [Setup] menu group.

 Image
Black Level (Brightness)
While Level (Contrast)
Gamma
Hue
Saturation
Sharpness Type
Sharpness Gain...

24 
The submenus display different items depending on the input signal. Items in submenus that contain further submenus are marked with “” .
 Signal
 3: Display Aspect Ratio
Auto
Normal
Squeeze
Smart Zoom
Zoom
Special
 4
Through 5
 4: Signal Status
Resolution
Sync Type
Sync Polarity
Frequency
Source Equipmet (HDMI only)
 Setup
 9: Location
Front/Table
Front/Ceiling
Rear/Table
Rear/Ceiling
 10: Remote Control Sensor
Front & Rear
Front
Rear
Off
 11: Remote Control ID
ID 1
ID 2
 12: Menu Color
Monotone...

25
Menu
7 
Menu group items and functions
Memo
•You can only select items displayed with a  in advanced mode.

You can adjust the image when the unit is receiving an input signal.
Black Level
(Input signal)
Video/S-Video/Component/RGB TV
Contrast
(Input signal)
RGB PC
Gamma
(Input signal)
Video/S-Video/Component/RGB TV/RGB PC
Brightness
 (Input signal)
RGB PC
White Level
(Input signal)
Video/S-Video/Component/RGB TV
Output signal
Input signal Black White White
Output signal
Input signal Black White...

26
Menu items
Adjusts color temperature.
Adjusts the level of white in colors between red and blue, and between green and magenta.
Increase the color temperature to increase the amount of blue in an image, giving bright
color tones. Reduce the color temperature to increase the amount of red, giving a darker,
more relaxed atmosphere to the image.
Choices: 5,000 to 10,000
Changes the characteristics of the filter used for “Sharpness Gain”
(described below).
Choices: Off / L / ML / MH / H
Adjusts the...