Yamaha Mtx5d Manual

Various Procedures
MTX5-D Owner’s Manual21
GPI (General Purpose Interface) devices can be connected to 
the rear-panel [GPI] connectors.  GPI allows a variety of control 
signals to be exchanged with  external controllers or other 
devices.
The MTX5-D provides 16 input ports and 8 output ports.
• The +5VDC terminals have an output voltage of 5V. The maximum current draw is 100 mA total for the two termi-
nals. If you are using a switch/va riable resistor and an LED/
relay simultaneously, connect  one...

Various Procedures
MTX5-D Owner’s Manual22
The MTX5-D can use commercially available SD memory 
cards to play back audio files such as music and sound effects 
without needing to connect a CD player or other audio device. 
The MTX5-D can play back audio files in either MP3 or WAV 
formats.
Here we explain how to handle SD  memory cards. In order to 
play back audio files saved on an SD memory card, you must 
make settings in MTX-MRX Editor. For details, refer to “MTX-
MRX Editor User Guide.”
Inserting...

Various Procedures
MTX5-D Owner’s Manual23
4. When initialization is completed, power-off the 
MTX5-D once again.
5. Set the rear panel DIP switches 7 and 8 to the  “RESUME” position.
6. Power-on the MTX5-D again.
The MTX5-D will start up  in its factory-set state. 

MTX5-D Owner’s Manual24
Appendix
Troubleshooting
The Yamaha Pro Audio website provides a FAQ (a list of freque ntly asked questions, with answers).
http://www.yamahaproaudio.com/
SymptomPossible cause, and action 
The device does not turn on, or 
the panel LEDs do not light up. Connect the power cord properly.
Make sure that the power switch is turned on.
If the power still does not turn on, contact your Yamaha dealer.
Can’t exchange data between the 
MTX5-D and MTX-MRX Editor 
(MTX5-D is not shown in...

Appendix
MTX5-D Owner’s Manual25
Preset does not switch at the time 
specified by the scheduler.The MTX5-D’s clock is set by sending clock data from the computer via MTX-MRX Editor to the 
MTX5-D. Make sure that the computer’s clock is set correctly.
Have you made the correct scheduler settings in MTX-MRX Editor? If the [SCHEDULER] indicator 
is not lit or flashing, it may be that settings were not made correctly in MTX-MRX Editor.
The [ALERT] indicator is flashing. An error has occurred. The alert...

Appendix
MTX5-D Owner’s Manual26
Messages
Warnings and certain other types of information are displayed via the MTX5-D front panel indicators.
Messages are also displayed in the  Dante Controller Error Status field.
Each indicator lights or fl ashes as described below:
Information Messages
The status is shown by the lit/ flashing state of the indicator.
If the orange [SYNC] indicator is unlit, the unit is operating normally.
If the green [SYNC] indicator is un lit, the unit’s clock is unconfirmed....

Appendix
MTX5-D Owner’s Manual27
Alert list
This is a list of the alerts that may be indicated in the front panel [PRESET] display.
Alert 
numberMeaningResponse
01–09 The device has not started up correctly. Turn the power off, then turn on after waiting at least 6 seconds. If this does not 
solve the problem, please initialize the me
mory. Should this also fails, contact your 
Yamaha dealer.
10 The internal backup battery has been 
completely exhausted or is not installed. When you turn off the power,...

Appendix
MTX5-D Owner’s Manual28
50 The UNIT ID is set to “00.”Set the UNIT ID to something other than “00.”
51 Devices with identical UNIT IDs were 
found connected within the same net-
work. Change the UNIT ID so that there are no duplicates.
52 A communication error occurred with the 
[DCP] connection. • If an error was shown in the DCP panel, refer to the DCP owner’s manual and 
take the appropriate action.
• Ensure that the panel ID of the DCP units do not conflict.
• Verify that the cables are...

Appendix
MTX5-D Owner’s Manual29
Specifications
* Specifications and appearance are subject to change without notice for improvement.
European Models
Inrush Current based on EN 55103-1: 2009
2A (on initial switch-on)
2A (after a supply interruption of 5s)
Conforms to Environments: E1, E2, E3 and E4
Product specifications
Dimensions (W x H x D) 480(W) x 88(H) x 351(D)mm, 2U
Weight 6.3kg
Power supply voltage Japan: 100V 50/60Hz
US/Canada: 110V–240V 50/60Hz
Others: 100V–240V 50/60Hz
Power consumption 65W...

Appendix
MTX5-D Owner’s Manual30
Input/Output Characteristics
ANALOG INPUT CHARACTERISTICS
• In these specifications, 0dBu = 0.775 Vrms., 0dBV = 1.00 Vrms.
• All input AD converters are 24bit linear, 128times oversampling.
• +48V DC (phantom power) is supplied to INPUT EUROBLOCK connectors via each individual software controlled switch.
ANALOG OUTPUT CHARACTERISTICS
• In these specifications, 0dBu = 0.775 Vrms.
• All output DA converters are 24bit, 128times oversampling.
Dimensions
Input 
Te rm i n a l...