Yamaha Lpx 510 User Manual

Advanced Operations
37
Using the Menu Functions
Menus can be operated using the projectors control panel and also by using the remote control.
1Display the menu screen.
Press the [MENU] button on the projectors 
control panel or the   button on the remote 
control.
The menu appears.
Full menus consist of a main menu and sub-
menus.
2Select the items to be changed in the 
main menu.
If using the projectors control panel, press the   
or   button to select a command, and then press 
the  button.
If using...

Using the Menu Functions
38
4
Change the setting.
If using the projectors control panel, press the 
 or   button to make the setting.
If using the remote control, tilt the   button to 
the left or right.
If a selection menu is displayed, select an item, 
and then press the   button on the projectors 
control panel or the   button on the remote 
control to confirm the setting.
5
Exit the menu display.
Press the [MENU] button on the projectors 
control panel or the   button on the remote 
control.
1
Press...

39
Advanced Operations
Using the Menu Functions
2
Select an item to be set.
If using the projectors control panel, press the 
 or   button to select a command. 
If using the remote control, tilt the   button up 
or down to select a command. 
The line menu item changes when a button is 
pressed.
3Change the setting.
If using the projectors control panel, press the 
 or   button to make the setting.
If using the remote control, tilt the   button to 
the left or right. 
4Exit the menu display.
Press the...

4
Troubleshooting
This chapter describes troubleshooting procedures for the projector.
When Having Some Trouble ........................................................... 42
When the Indicators Provide No Help ........................................... 44
•
•• •Problems relating to images ....................................................................................................44
•
•• •Problems when projection starts...

42
When Having Some Trouble
The projector is provided with the following three 
indicators which notify you of the operating status of the 
projector. The following tables show what the indicators 
mean and how to remedy the problems that they indicate.
*If the   indicator does not light when the power is 
turned on, the power cord may not be connected correctly 
or the power may not be supplied.
The following tables show what the indicators mean and how to remedy problems that they indicate.
    : lit...

43
Troubleshooting
When Having Some Trouble
Standby condition (No abnormality)
If you press the [STANDBY/ON] button on the projectors 
control panel or the   button on the remote control, 
projection will start after the warm-up is complete.p.6
Warm-up in progress (No abnormality)
The warm-up period is approximately 30 seconds. Wait for short 
while. The indicator will stop flashing and light green.
The power cannot be turned off while warm-up is in progress.p.7
Projection in 
progress(No abnormality)...

44
When the Indicators Provide No Help
If any of the following problems occur and the indicators do not offer a solution, refer to the pages given for 
each problem.
 No images appear
Probable relating to images
 No images appear
Projection does not start, the projection 
area is completely black, the projection 
area is completely blue, etc.
See 
below Image colors are not right
The whole image appears purplish or 
greenish, images are black & white, 
colors appear dull, etc.
(Computer monitors and LCD...

45
Troubleshooting
When the Indicators Provide No Help
 The message Not Supported. is displayed
 The message No Signal. is displayed
 Images are fuzzy or out of focus
Are the image signal format settings 
correct?When a composite video or S-Video signal is being input.
If images cannot be projected even when the Video Signal menu 
command is set to Auto, change the setting to the signal format 
for the connected equipment. 
Setup - Input Signal - Video Signal (p.36)
If connected to the INPUT A or INPUT B...

When the Indicators Provide No Help
46
 Interference or distortion appear in images
 Image is truncated (large) or small
Are the image signal format settings 
correct?When a composite video or S-Video signal is being input.
If images cannot be projected even when the Video Signal menu 
command is set to Auto, change the setting to the signal format 
for the connected equipment. 
Setup - Input Signal - Video Signal (p.36)
If connected to the INPUT A or INPUT B port
Check that the connectors of the...

47
Troubleshooting
When the Indicators Provide No Help
 Image colors are not right
 Images appear dark
 Projection stops automatically
 Vertical interference appears in the projected images
Are the image signal format settings 
correct?When a composite video or S-Video signal is being input.
If images cannot be projected even when the Video Signal menu 
command is set to Auto, change the setting to the signal format 
for the connected equipment. 
Setup - Input Signal - Video Signal (p.36)
If the signal...