Yamaha HTR-5550 AV Receiver Owners Manual

47
English INTRODUCTION
PREPARATIONBASIC OPERA-
TIONADVANCED
OPERATIONADDITIONAL
INFORMATION
APPENDIX
REMOTE CONTROL FEATURES
Setting the manufacturer code
You can control other components by setting a
manufacturer code. Codes can be set for each of the 9
component controls.
The following table shows factory-set component
(Library: component category) and the manufacturer code
for each component control.
1Press an input selector button or Å/ı to
select the component you want to set up.
2Press CODE SET...

48
REMOTE CONTROL FEATURES
Controlling other components
DVD player VCR TV, digital/cable TV CD player CD/MD recorder Tuner
1AV POWER *1Power *1Power *3VCR power *1Power *1Power *1Power
2TV POWER *2TV power *2TV power *2TV power *2TV power *2TV power *2TV power
3TV CH + *2TV channel up *2TV channel up TV channel up *2TV channel up *2TV channel up *2TV channel up
TV CH –*2TV channel down*2TV channel down TV channel down*2TV channel down*2TV channel down*2TV channel down
4TV VOL + *2TV volume up *2TV volume...

49
English INTRODUCTION
PREPARATIONBASIC OPERA-
TIONADVANCED
OPERATIONADDITIONAL
INFORMATION
APPENDIX
You can adjust the output level of each effect speaker
(center, rear left and right, and subwoofer) while listening
to a source.
Adjustment should be made with the remote control.
1Press AMP.
(While playing a source)
2Press LEVEL repeatedly to select the
speaker(s) you want to adjust.
Each time you press LEVEL, the selected speaker
changes and appears on the front panel display as
follows: center, rear...

50
You can adjust the time difference between the beginning
of the sound from the main speakers and the beginning of
the sound effect from the rear speakers. The larger the
value, the later the sound effect is generated. The delay
time can be individually adjusted to all DSP programs.
The following table shows factory-set delay time.
AMP
RECDISC SKIP
SET MENU
SELECT PRESET/CHA/B/C/D/E
AUDIO
LEVELMENU
TEST
STEREOEFFECT
RETURNDISPLAY
TITLE
MUTE
+ –
HALLENTER-
TAINMENT
TV
SPORTSMONO
MOVIE
SELECT
MATRIX 6.1...

51
English INTRODUCTION
PREPARATIONBASIC OPERA-
TIONADVANCED
OPERATIONADDITIONAL
INFORMATION
APPENDIX
Changing parameter settings
You can adjust the values of PRO LOGIC  Music
parameters so the sound fields are recreated accurately in
your listening room.
Adjustments should be made with the remote control.
1Press AMP.
2Select PRO LOGIC  Music.
3Press u / d to select the
parameter.
4Press j / i to change the
parameter value.
5Repeat steps 3 and 4 above as necessary to
change other parameters.
SELECT...

52
TROUBLESHOOTING
Refer to the chart below when this unit does not function properly. If the problem you are experiencing is not listed
below or if the instruction below does not help, set this unit to the standby mode, disconnect the power cord, and
contact the nearest authorized YAMAHA dealer or service center.
General
Problem
This unit fails to turn
on when STANDBY/
ON (or SYSTEM
POWER) is pressed,
or enters in the
standby mode soon
after the power has
been turned on.
No sound.
The picture does not...

53
English INTRODUCTION PREPARATIONBASIC
OPERAIONTADVANCED
OPERATIONADDITIONAL
INFORMATION
APPENDIX
TROUBLESHOOTING
Problem
The sound suddenly
goes off.
Only the speaker on
one side can be
heard.
No sound from the
effect speakers.
No sound from the
center speaker.
No sound from the
rear speakers.
No sound from the
subwoofer.
Poor bass
reproduction.
Cause
The protection circuit has been activated
because of a short circuit, etc.
The sleep timer has functioned.
The sound is muted.
Incorrect cable...

54
TROUBLESHOOTING
Problem
A “humming” sound
can be heard.
The volume level
cannot be increased, or
the sound is distorted.
The sound effect
cannot be recorded.
A source cannot be
recorded by a digital
recording component
connected to the
DIGITAL OUTPUT jack
of this unit.
The sound field
parameters and some
other settings on this
unit cannot be
changed.
This unit does not
operate properly.
“CHECK SP WIRES”
appears on the front
panel display.
There is noise
interference from digital
or high-frequency...

55
English INTRODUCTION PREPARATIONBASIC
OPERAIONTADVANCED
OPERATIONADDITIONAL
INFORMATION
APPENDIX
TROUBLESHOOTING
Tuner
FM stereo reception is
noisy.
There is distortion, and
clear reception cannot
be obtained even with a
good FM antenna.
The desired station
cannot be tuned in with
the automatic tuning
method.
Previously preset
stations can no longer
be tuned in.
The desired station
cannot be tuned in with
the automatic tuning
method.
There are continuous
crackling and hissing
noises.
There are...

56
GLOSSARY
Dolby Surround
Dolby Surround uses a 4 channel analog recording system
to reproduce realistic and dynamic sound effects: 2 main
left and right channels (stereo), a center channel for
dialog (monaural), and a rear channel for special sound
effects (monaural). The rear channel reproduces sound
within a narrow frequency range.
Dolby Surround is widely used with nearly all video tapes
and laser discs, and in many TV and cable broadcasts as
well. The Dolby Pro Logic decoder built into this unit...