Yamaha HTR-5550 AV Receiver Owners Manual

37
English INTRODUCTION
PREPARATIONBASIC
OPERATIONADVANCED
OPERATIONADDITIONAL
INFORMATION
APPENDIX
TUNING
Exchanging preset stations
You can exchange the assignment of two preset stations.
The example below describes the procedure for
exchanging preset station “E1” with “A5”.
1Tune in to preset station “E1” by using the
A/B/C/D/E and PRESET/TUNING l / h.
See “Tuning in to a preset station” at left.
2Press and hold PRESET/TUNING (EDIT) for
more than 3 seconds.
“E1” and the “MEMORY” indicator flash on...

38
Use this feature to automatically set this unit in the
standby mode after the amount of time you have set. The
sleep timer is useful when you are going to sleep while
this unit is playing or recording a source. The sleep timer
also automatically turns off the external component(s)
connected to AC OUTLET(S).
The sleep timer can only be set with the remote control.
y
•By connecting a commercially available timer to this unit, you
can also set a wake-up timer. Refer to the operation instructions
of the...

39
English INTRODUCTION
PREPARATIONBASIC
OPERATIONADVANCED
OPERATIONADDITIONAL
INFORMATION
APPENDIX
INPUT
POWER
SLEEPCODE SETSTANDBYTRANSMIT
6CH INPUT
SYSTEM
V-
AUX D-
TV/CBL
TV INPUT TV MUTE
VOLUME
MUTE
AMP POWER POWER
AV TV
VCRADVDMD/CD-R TUNER CD
+
–+
– +
–TV CH TV VOL
HALLENTER-
TAINMENTROCK
CONCERTJAZZ CLUB
B2
SLEEP
6CH INPUTV-
AUX D-
TV/CBL
AMP
VCR
A
DVDMD/CD-R TUNER CD
B
Front panel Remote controlor
RECORDING
Notes
•Do a test recording before you start an actual recording.
•When this unit is set...

40
SELECT PRESET/CH+ –
Adjusting the items on the SET
MENU
Adjustment should be made with the remote control.
Note
•Some items require extra steps.
1Press AMP.
2Press SET MENU to enter
the SET MENU.
3Press u/d repeatedly to
select the item you want
to adjust (1 to 10).
y
•By pressing SET MENU repeatedly, you can select items in the
same order as when pressing d.
4Press j / i once to enter
the setup mode of the
selected item.
The last setting you adjusted
appears on the front panel
display.
Depending on...

41
English INTRODUCTION
PREPARATIONBASIC OPERA-
TIONADVANCED
OPERATIONADDITIONAL
INFORMATION
APPENDIX
SET MENU
5Press j / i repeatedly to
change the setting of the
item.
6Press u/d repeatedly until the menu
disappears or simply press one of the DSP
program group buttons to exit SET MENU.
SELECT PRESET/CH+ –
SELECT PRESET/CH+ –
STEREO
EFFECT
HALLENTER-
TAINMENT
TV
SPORTSMONO
MOVIE
SELECT
MATRIX 6.1
MOVIE
 THEATER 1MOVIE
 THEATER 2
    /DTS
SUR.
ROCK
CONCERTJAZZ CLUB34 2 1
5
90
ENTER+10
67 8
1 SPEAKER SET...

42
SET MENU
1B MAIN (main speaker mode)
Choices: LARGE, SMALL
LARGE
Select this if you have large main speakers. The entire
range of the main left and right channel signal is directed
to the main left and right speakers.
SMALL
Select this if you have small main speakers. The low-
frequency signals (90 Hz and below) of the main channel
are directed to the speakers selected with “1D BASS”.
1C REAR LR (rear speaker mode)
Choices: LRG (large), SML (small), NON (none)
LRG
Select this if you have large rear...

43
English INTRODUCTION
PREPARATIONBASIC OPERA-
TIONADVANCED
OPERATIONADDITIONAL
INFORMATION
APPENDIX
SET MENU
2 LFE LEVEL
Use this feature to adjust the output level of the LFE
(low-frequency effect) channel when playing back a
Dolby Digital or DTS signal. The LFE signal carries the
low-frequency special effect sound which is only added to
certain scenes.
Control range:
SPEAKER ............–20 to 0 dB
HEADPHONE .....–20 to 0 dB
Initial setting: 0 dB
1Press d/u to select the item to be adjusted.
2Press j...

44
SET MENU
7 I/O ASSIGN (input/output
assignment)
It is possible to assign jacks according to the component
to be used if this unit’s COMPONENT VIDEO input jack
or DIGITAL INPUT/OUTPUT jack settings (component
names for jacks) differ from that component. This makes
it possible to change the jack assignment and effectively
connect more components.
Once you assign, you can select that component with
INPUT l / h (or the input selector buttons on the
remote control).
7A CMPNT-V INPUT for
COMPONENT VIDEO...

45
English INTRODUCTION
PREPARATIONBASIC OPERA-
TIONADVANCED
OPERATIONADDITIONAL
INFORMATION
APPENDIX
SET MENU
8 INPUT MODE (initial input
mode)
Use this feature to designate the input mode for sources
connected to the DIGITAL INPUT jacks when you turn
on this unit (see page 25 for details about the input
mode).
Choices: AU TO, LAST
AUTO
Select this to allow this unit to automatically detect the
type of input signal and select the appropriate input mode.
LAST
Select this to set this unit to automatically...

46
REMOTE CONTROL FEATURES
In addition to controlling this unit, the remote control can operate other A/V components made by YAMAHA and other
manufacturers. To control other components, you must set up the remote control with the manufacturer codes.
Control area
Controlling this unit
The shaded areas below can be used to control this unit
when the AMP mode is selected. Press AMP to select the
AMP mode.
Controlling other component
The shaded areas below can be used to control other
components. Each...