Yamaha Dtxpress 3 Manual

11
This mode contains various settings related to trigger
input from the pads and trigger sensors that are con-
nected to the DTXPRESS III.
It allows you to adjust pad sensitivity and assign drum
voices to each trigger input. Trigger Setup data consists
of seven preset types (No. 1-7) and four original setup
types (No. 8-11) for storing user setup data.
What you can do with the Trigger Setup Edit
Mode
The Trigger Setup Edit Mode lets you alter a variety of settings for
each of the trigger inputs jacks...

12
TRIG IN= 1
Type=  KP
w
q
TRIG IN= 1 ( 0%)
Gain=64 MVel= 32 Level Display
w
e
q
Trigger Setup Edit Mode
1.  INPUT Parameters
Contains specific settings for each of the pads (1-10).
This function is divided into the following 6 pages.
1-1.Pad Type.......................................................... 12
1-2. Gain, Minimum Velocity ................................... 12
1-3. Velocity Curve ................................................. 13
1-4. Self Rejection, Rejection...

13
If “HH contrler” is set for the pad type, the value set here will
be transmitted as the velocity.
The trigger input level will be displayed as a % in the upper right
hand corner of the display. The maximum velocity (input level
99%) will be 127. The level is low when the pad is hit the weakest
so a wider dynamic range will be possible.
* This value will be automatically set after the appropriate pad
type is set in [1-1. Pad Type]. Some fine-tuning of the value will
be necessary.
1-5.  Specific...

14
2.  COMMON Parameters
Contains common settings for all pad inputs (1-10).
This group is divided into the following 4 pages.
2-1. Hi-Hat Offset .................................................... 14
2-2. Increment/Decrement ...................................... 14
2-3. Input Exchange ............................................... 15
2-4. Trigger Setup Name ........................................ 15
2-1.  Hi-Hat Offset
This sets the value of the data sent by a foot controller connected
to the HI HAT...

15
* Even when the drum kit is changed, the pads connected to the
assigned trigger input jacks will retain their increment/decre-
ment functions. To assign this function to each drum kit, refer to
the Drum Kit Voice Edit mode’s [2-6. Function] (P. 21)
2-3.  Input Exchange
Switches the trigger signal from the pads between trigger input
jacks 1 and 9/10.
TRIG Common
TrgName=Medium
q
Trigger Setup Edit Mode
TRIG Common
In Excg=  normal
q
q In Excg (Input Exchange)
normal: Normal operation
9åß10: Re-routes...

16
Drum Kit Voice Edit Mode
This mode lets you set which voice and how it will be
triggered for each pad (trigger input source) in the cur-
rently selected drum kit.
What you can do with the Drum Kit Voice
Edit Mode
This mode contains various settings related to the currently se-
lected drum kit (data in the edit buffer for the drum kit).
You can edit both preset (No. 1-48) and user drum kits (No. 49-
80).
The edited drum kit can be stored in a User Drum Kit (No. 49-80)
using the Store Operation.
*...

17
Drum Kit Voice Edit Mode
Drum Kit Voice Edit Mode Function List
Page
1. Voice Parameters .................................................... 17
1-1. Voice ................................................................ 18
1-2. Volume, Pan .................................................... 18
1-3. Tuning .............................................................. 18
1-4. Layer Balance .................................................. 19
1-5. Decay, Cutoff Frequency...

18
Drum Kit Voice Edit Mode
crashCCup switch input for Trigger Input Jack 7.
openPad input (when the hi-hat controller is not fully closed)
for Trigger Input Jack 8.
openRRim switch input (when the hi-hat controller is not fully
closed) for Trigger Input Jack 8.
closePad input (when the hi-hat controller is fully closed)
for Trigger Input Jack 8.
closeRRim switch input (when the hi-hat controller is fully
closed) for Trigger Input Jack 8.
footClEvent when the hi-hat controller is depressed for Trig-
ger...

19
1-4.  Layer Balance
When a drum voice is made up of 2 layers (a single voice consist-
ing of 2 voice waves), this function sets the volume balance be-
tween the 2 layers that are delivered by each layer w of the input
source q.
* When only a 1 layer voice is set, this setting will be ignored.
1-6.  Note Number
This function sets the MIDI note number for each layer w that is
transmitted when a signal is received from the input source q.
Drum Kit Voice Edit Mode
q IN (Input Source)
w Layer Number...

20
2.  Input Common Parameters
This sub-mode sets the common settings between 2 layers for voice
parameters of each pad’s input source.
The Input Common Parameters sub-group is divided into the fol-
lowing 8 pages.
2-1. Cross Fade ...................................................... 20
2-2. Reverb Send .................................................... 20
2-3. Alternate Group, Key Assign Mode ................. 20
2-4. Hold Mode ....................................................... 21
2-5. Key Off...