Yamaha Dpx 530 User Manual

Downloaded from www.Manualslib.com manuals search engine 17
◆Viewing computer images
Preparation:
 Turn on the power of the connected computer.
1. Confirm the POWER indicator lights up red.
 If the projector was turned off before the lamp was cooled down sufficiently last time, the fan may start rotating and the STA NDBY/ON 
button may not work after the power cable is  plugged. (The STATUS indicator blinks green.) After the fan stops rotating, press the 
STANDBY/ON button to turn ba ck on the POWER...

Downloaded from www.Manualslib.com manuals search engine 18
AUTO / AUTO SYNC buttons
When the image being input from the computer is displaced, carry out the following procedure:
1. When the screen saver has been enabled, disable it.
2. Display a bright image (such as a full-screen display of the Recycle Bin window).
3. Press the AUTO button on the remote control or the AUTO SYNC ( ) button on the projector. The projector automatically makes optimum  positional settings for the input signal.
 If the...

Downloaded from www.Manualslib.com manuals search engine 19
◆Menu overview
Menus are not displayed when no signal is received by the projector.
After selecting the items marked with  , press the ENTER button.
*1: Not available when sRGB is set to ON.
*2: Setting range differs depending on the input signals.
*3: Refer to the chart below for availability / unavailability.
SATURATION Unavailable when the input source is  DVI or the D-SUB source is an RGB signal.
HUE Available only when the VIDEO or S-VIDE O...

Downloaded from www.Manualslib.com manuals search engine 20
How to set the menus
Following describe how to set AUTO POWER OFF time as an example.
1. Press the MENU button. If no signal is input, the menu does not appear. 
2. Press the   or   button to select a menu to use.
3. Press the ENTER button (or   button).
4. Press the   or   button to select an item to adjust. 
5. Set the selected item by pressing the   or   button. 
To cancel the menu:
6. Press the MENU button several times.
Important
 If the...

Downloaded from www.Manualslib.com manuals search engine 21
◆Menu settings
Set the following items on their relevant menus.
1. IMAGE menu
1. IMAGE menu 2.SETUP menu 3. INITIAL menu 4.SIGNAL menu
ITEM SETTING FUNCTION
CONTRAST 0 – 60 Use to adjust the contrast  of the projected image (see page 24).
BRIGHTNESS ±30 Use to adjust the brightness  of the projected image (see page 24).
WHITE ENHANCE DEFAULT The appropriate wh ite enhance value is automatically selected depending on the input signal. 
Select...

Downloaded from www.Manualslib.com manuals search engine 22
2. SETUP menu
3. INITIAL menu
ITEM SETTING FUNCTION
KEYSTONE ±20 Use to correct vertical keystone distortion.
AU TO  P OW E R  
ON ON / OFF When ON is selected, the lamp is automati
cally lit when the power cable is plugged in the 
wall outlet.
The projector is in the stand-by mode when the lamp is off. Use the remote control to turn on 
the lamp.
AU TO  P OW E R  
OFF OFF / 5 – 60min Use to set the time elapsed before the 
projector enters the...

Downloaded from www.Manualslib.com manuals search engine 23
4. SIGNAL Menu
 Horizontal strips may appear on the enlarged projected image; this is not a malfunction.
 When you change the horizontal or vertical  position to a large extent, noise may appear.
 The adjustable range of the vertical posi tion varies depending on the type of the input  signal. In some cases, the image may stay in the same 
position even when the setting value is  changed; this is not a malfunction.
 D-SUB INPUT will automati...

Downloaded from www.Manualslib.com manuals search engine 24
◆Adjusting brightness (C ONTRAST and BRIGHTNESS)
You can make adjustments for the brightness of  the projected image using the menu (see page 21).
1. Display the IMAGE menu.
2. Select CONTRAST or  BRIGHTNESS by pressing the   or   button.
3. Adjust the selected item by pressing the   or   button.
To cancel the menu:
4. Press the MENU button
CONTRAST
Select to adjust the contrast of the image. Every time the   button is pressed, the image becomes...

Downloaded from www.Manualslib.com manuals search engine 25
◆Adjusting color (SATURATION and HUE)
You can adjust the color of the projecte d image using the menu (see page 21).
1. Display the IMAGE menu.
2. Select SATURATION or HUE by pressing the   or   button.
 SATURATION is unavailable when the D-SUB source is an  RGB signal or DVI is selected as the input source.
 HUE is available only when  the NTSC signal is input.
3. Adjust the selected item by pressing the   or   button.
To cancel the menu:
4....

Downloaded from www.Manualslib.com manuals search engine 26
This projector automatically and properly projects video signals supplied from the computer. Howe ver, some video signals may not be 
projected, depending on the type of the computer. In such a ca se, press the AUTO POSITION button on the projector or the AUTO b utton on 
the remote control (see page 18). When th e signal is still not projected properly, adjust the projected image using the SIGNAL  menu.
◆Adjusting computer images
Carry out the...