Yamaha Dpx 530 User Manual

Downloaded from www.Manualslib.com manuals search engine 7
◆Operational range
 Keep the remote control sensor out  of direct sunlight or fluorescent 
lamp light.
 Keep the remote control sensor at  least 2 m away from fluorescent 
lamps. Otherwise, the remo te control may malfunction.
 If there is an inverter-operated  fluorescent lamp near the remote 
control, the remote control operati on may become unstable. On this 
occasion, stick a commercially av ailable protection sticker on one 
of the...

Downloaded from www.Manualslib.com manuals search engine 8
◆Setting up your projector
Install the screen perpendicularly to the pr ojector. If the screen can not be installed in such a way, adjust the projection an gle of the projector as 
shown below. 
 Install the screen and projector so that the projector’s lens is placed at the horizontal position of the screen center.
 Do not install the screen where it is exposed  to direct sunlight or lighting. Light directly reflecting on the screen makes th e...

Downloaded from www.Manualslib.com manuals search engine 9
◆Screen size and projection distance
Refer to the following diagram  to determine the screen size.
When the aspect ratio of the screen is 4: 3, the positional relation between the projec ted image and the screen is as shown on the right. Refer to 
the following table for installation.
When the aspect ratio of the screen is 16:9
 The above figures are approximate and may be sl ightly different from the actual measurements.
When the aspect ratio...

Downloaded from www.Manualslib.com manuals search engine 10
Preparations:
 Make sure that the power of the projector and that of the video equipment are turned off.
◆Basic home theater system connection
Video player
DVD player
Set-top box or digital tuner
PB/CB (Blue)
P
R/CR (Red)
Y (Green)
Connections5  

Downloaded from www.Manualslib.com manuals search engine 11
◆Connecting to a video player, etc.
1. Connect one end (yellow) of a commercially available video 
cable to the VIDEO terminal of this projector.
2. Connect the other end (yellow)  of the video cable to the 
VIDEO terminal of the video equipment.
When the video equipment is equipped with the
S-video terminal, make the connection as follows.
1. Connect one end of the supplied S-video cable to the 
S-VIDEO terminal of this projector.
2. Connect...

Downloaded from www.Manualslib.com manuals search engine 12
◆DVI-D connections
You can project high-quality images by c onnecting the DVI terminal of this projecto r to video equipment having a DVI-D output t erminal.
 For connection to the DVI terminal, us e a commercially available DVI-D cable.
 Select DVI as the input source.
 Only RGB signals are supported. Comp onent video signals are not supported.
When you connect this projector and a DVI-Digital device (such as a DVD player) via the DVI...

Downloaded from www.Manualslib.com manuals search engine 13
◆Connecting the projector to a computer
Preparation:
 Make sure that the power of the projector  and that of the computer are turned off.
 When connecting the projector to a desktop computer, disc onnect the RGB cable that is connected to the monitor.
For analog connections:
1. Connect one end of the supplied RGB cable to the D-SUB 
terminal of this projector.
2. Connect the other end of the RGB cable to the monitor port  of the computer.
...

Downloaded from www.Manualslib.com manuals search engine 14
◆Viewing video images
Preparation:
 Turn on the power of the connected video equipment.
1. Confirm the POWER indicator lights up red.
 If the projector was turned off before the lamp was cooled down sufficiently last time, the fan may start rotating and the STA NDBY/ON 
button may not work after the power cable is  plugged. (The STATUS indicator blinks green.) After the fan stops rotating, press the 
STANDBY/ON button to turn ba ck on the...

Downloaded from www.Manualslib.com manuals search engine 15
To stop projecting:
1. Press the STANDBY/ON button on the projector or the STANDBY ( ) button on the remote control.
 A confirmation message is displayed.
 To cancel the procedure, wait  a while or press the MENU button.
2. Press the STANDBY/ON button on the projector or  the STANDBY ( ) button on the remote control again.
 The lamp goes out and the projec tor goes into a cooling period. In this conditi on, the POWER indicator turns red and...

Downloaded from www.Manualslib.com manuals search engine 16
Setting the aspect ratio
You can change the aspect ratio of the input video signal (or the ratio of width to height of the image). Change the setting ac cording to the type 
of the input video signal.
Bold frames   are recommended modes.
Changing the settings
With the remote control:
1. Press the ASPECT button.
 Every time the ASPECT button is pressed,  the aspect mode changes from DEFAULT to NORMAL, to SQUEEZE, to ZOOM, to 
THROUGH, and back...