Yamaha 2007 R6 Service

IMPORTANT INFORMATION
1-12
EAS20230
BEARINGS AND OIL SEALS
Install bearings “1” and oil seals “2” so that the 
manufacturer’s marks or numbers are visible. 
When installing oil seals, lubricate the oil seal 
lips with a light coat of lithium-soap-based 
grease. Oil bearings liberally when installing, if 
appropriate.
CAUTION:
ECA13300
Do not spin the bearing with compressed air 
because this will damage the bearing surfac-
es.
EAS20240
CIRCLIPS
Before reassembly, check all circlips carefully 
and replace...

CHECKING THE CONNECTIONS
1-13
EAS20250
CHECKING THE CONNECTIONS
Check the leads, couplers, and connectors for 
stains, rust, moisture, etc.
1. Disconnect:
Lead
Coupler
Connector
2. Check:
Lead
Coupler
Connector
Moisture → Dry with an air blower.
Rust/stains → Connect and disconnect sev-
eral times.
3. Check:
All connections
Loose connection → Connect properly.
NOTE:
If the pin “1” on the terminal is flattened, bend it 
up.
4. Connect:
Lead
Coupler
Connector
NOTE:
Make sure all connections are...

SPECIAL TOOLS
1-14
EAS20260
SPECIAL TOOLS
The following special tools are necessary for complete and accurate tune-up and assembly. Use only 
the appropriate special tools as this will help prevent damage caused by the use of inappropriate tools 
or improvised techniques. Special tools, part numbers or both may differ depending on the country.
When placing an order, refer to the list provided below to avoid any mistakes.
NOTE:
For U.S.A. and Canada, use part number starting with “YM-”, “YU-”, or...

SPECIAL TOOLS
1-15
Oil filter wrench
90890-01426
YU-384113-11
Oil pressure gauge set
90890-031203-13
Oil pressure adapter H
90890-031393-13
Steering nut wrench
90890-01403
Spanner wrench
YU-339753-27, 4-58
Fork spring compressor
90890-01441
YM-014414-47, 4-52
Rod holder
90890-01434
Damper rod holder double ended
YM-014344-47, 4-52
Damper rod holder
90890-01506
YM-015064-48, 4-49
Fork seal driver
90890-01442
Adjustable fork seal driver (36–46 mm)
YM-014424-50 Tool name/Tool No. IllustrationReference 
pages 

SPECIAL TOOLS
1-16
Rod puller
90890-01437
Universal damping rod bleeding tool set
YM-A87034-51, 4-52
Rod puller attachment (M10)
90890-01436
Universal damping rod bleeding tool set
YM-A87034-51, 4-52
Ring nut wrench
90890-01268
Spanner wrench
YU-012684-58
Ring nut wrench
90890-01507
YM-015074-67, 4-69
Damper rod holder (24 mm)
90890-01328
YM-013284-67, 4-68
Valve spring compressor
90890-04019
YM-040195-19, 5-24 Tool name/Tool No. IllustrationReference 
pages
YM-A8703
YM-A8703 

SPECIAL TOOLS
1-17
Valve spring compressor attachment
90890-04108
Valve spring compressor adapter 22 mm
YM-041085-19, 5-24
Valve guide remover (ø4.5)
90890-04116
Valve guide remover (4.5 mm)
YM-041165-21
Valve guide installer (ø4.5)
90890-04117
Valve guide installer (4.5 mm)
YM-041175-21
Valve guide reamer (ø4.5)
90890-04118
Valve guide reamer (4.5 mm)
YM-041185-21
Valve spring compressor
90890-041095-24
Sheave holder
90890-01701
Primary clutch holder
YS-01880-A5-28, 5-29, 
5-31
Flywheel puller...

SPECIAL TOOLS
1-18
Universal clutch holder
90890-04086
YM-910425-41, 5-45
Thickness gauge
90890-03180
Feeler gauge set
YU-26900-95-41
Piston pin puller set
90890-01304
Piston pin puller
YU-013045-60
Radiator cap tester
90890-01325
Radiator pressure tester
YU-24460-016-3
Radiator cap tester adapter
90890-01352
Radiator pressure tester adapter
YU-339846-3 Tool name/Tool No. IllustrationReference 
pages
0.400.30
0.350.250.200.150.10
0.05
0.03
0.50
YU-01304
YU-24460-01
YU-33984 

SPECIAL TOOLS
1-19
Pressure gauge
90890-03153
Pressure gauge
YU-031537-12
Fuel pressure adapter
90890-03176
YM-031767-12
Digital circuit tester
90890-03174
Model 88 Multimeter with tachometer
YU-A19277-13
Ignition checker
90890-06754
Opama pet-4000 spark checker
YM-344878-92 Tool name/Tool No. IllustrationReference 
pages 

2
SPECIFICATIONS
GENERAL SPECIFICATIONS........................................................................ 2-1
ENGINE SPECIFICATIONS............................................................................ 2-2
CHASSIS SPECIFICATIONS........................................................................ 2-10
ELECTRICAL SPECIFICATIONS................................................................. 2-13
TIGHTENING...

GENERAL SPECIFICATIONS
2-1
EAS20280
GENERAL SPECIFICATIONS
Model
Model 2C05/2C08 (USA)
2C06 (California)
Dimensions
Overall length 2040 mm (80.3 in)
Overall width 700 mm (27.6 in)
Overall height 1100 mm (43.3 in)
Seat height 850 mm (33.5 in)
Wheelbase 1380 mm (54.3 in)
Ground clearance 130 mm (5.12 in)
Minimum turning radius 3600 mm (141.7 in)
Weight
With oil and fuel 182.0 kg (401 lb) (USA)
183.0 kg (403 lb) (California)
Maximum load 193 kg (425 lb) (USA)
192 kg (423 lb) (California)