Yaesu Musen Yaesu Vr 5000 Communications Reciever Operating Manual

VR-5000 OPERATING MANUAL19
Basic Operation
You can change the frequencies of stations in the above frequency list, i\
f desired.
Here is the procedure:
1. Tune the radio to the new frequency of the Broadcast Station on the list.
2. Press the  [
F ]
 key momentarily, then press the  [
4 (
SPL )
]
 key.
3. Rotate the  DIAL knob to set the cursor to the “ STATION FREQ. WRITE” menu, then
press the  [
ENT (
SET )
]
 key.
4. Press the  [

 (
 )
/ (
 )]
 keys to select the  Broadcast Station whose frequency...

VR-5000 OPERATING MANUAL20
Memory Operation
The VR-5000 provides a wide variety of memory system resources. These include:

2000 main memory channels, which may be separated into as many as 100 memory groups.

50 sets of band-edge memories (also known as “Programmable Memory Scan” channels).

Five PS (Pre Set) memory channels, providing one-touch storage and recall of prime
receiving frequencies.
MAIN MEMORY SYSTEM
Memory Storage
1. Select the desired frequency, while receiving on the MAIN VFO. Be sure...

VR-5000 OPERATING MANUAL21
Memory Operation
You can also configure the VR-5000 for recall of all memory channels (ignoring the memory
groups). To do this:
(1) Press the [
F]
 key momentarily, then press the [
ENT(
SET)]
 key.
(2) Rotate the DIAL knob to set the cursor to the “MR” menu, then press the [
ENT]
 key.
(3) Confirm that the cursor is on the “MR BANK”
menu selection, then press the [
• (
BEEP)]
 key
to change its setting to “All Mem.”
(4) Rotate the DIAL knob to set the cursor to the
“END” menu...

VR-5000 OPERATING MANUAL22
Memory Operation
ENHANCED MEMORY CHANNEL OPERATION
Memory Offset Tuning
Once you have recalled a particular memory channel, you may easily tune off that channel,
as through you were in the “VFO” mode.
1. With the VR-5000 in the memory mode, select the desired memory channel.
2. Press the [
BS(
BS SET)
MT]
 key momentarily.
3. Rotate the DIAL knob or press the [

(
)
/(
)]
 keys, as desired, to tune to a new
frequency.
4. If you wish to return to the original memory...

VR-5000 OPERATING MANUAL23
Memory Operation
Alpha-Numeric Keypad Sequence

Press the [
1(
AT T)]
 key repeatedly to toggle between the two available characters:
“1”  “Space”  “1” ……

Press the [
2(
LOCK)]
 key repeatedly to toggle among the seven available characters:
“2”  “A”  “B”  “C”  “a”  “b”  “c”  “2”  “A” ……

Press the [
3(
S.SCH)]
 key repeatedly to toggle among the seven available characters:
“3”  “D”  “E”  “F”  “d”  “e”  “ f ”  “3”  “D” ……

Press the [
4(
SPL)]
 key repeatedly...

VR-5000 OPERATING MANUAL24 Naming Memory Groups
1. Press the [
V/M(
MW)]
 key, if needed, to enter the memory mode.
2. Recall the memory group to which you wish to append a label, then press the [
BANK]
key.
3. Confirm that the cursor is on the “BANK TAG”
menu, then press the [
ENT(
SET)]
 key.
4. Program the alpha-numeric “label” which you
wish to recall using the DIAL knob and key-
pad, as described previously.
5. When you have completed the creation of the
label, press the [
ENT(
SET)]
 key.
6. Rotate...

VR-5000 OPERATING MANUAL25 Masking Memories
You may wish to “Mask” a certain Memory Channel’s data, when you no longer have a
reason to recall that channel.
To Mask a channel’s data:
1. Recall the Memory Channel to be masked.
2. Press the [
F]
 key momentarily, then press the [
V/M(
MW)]
 key.
3. Rotate the DIAL knob to set the cursor to the “Channel” menu, then press the
[
ENT(
SET)]
 key.
4. Press the [
F]
 key momentarily, then press the [
CLR(
PRI CLR)]
 key.
5. Confirm that the cursor is on the...

VR-5000 OPERATING MANUAL26 Alpha-Numeric Memory Recall
You can use the VR-5000’s powerful microprocessor system to search for Memory Chan-
nels according to their alpha-numeric label. In the example below, we shall set up the VR-
5000 to find all channels programmed with “POLICE” as an alpha-numeric label (e.g.
POLICE 1, POLICE 2, etc.).
1. Press the [
V/M(
MW)]
 key, if needed, to enter the memory mode.
2. Press the [
WIDTH(
BS STEP)]
 key to enable setup of Alpha-Numeric Memory Re-
call.
3. Program the...

VR-5000 OPERATING MANUAL27
To install a Memory Channel into the PMR Board:
1. Recall the memory channel which you wish to be monitoring for activity.
2. Press the [
F]
 key momentarily, then press the [
3(
S.SCH)]
 key.
3. The next-available PMR Board channel slot will be displayed, with an arrow alongside
it. Press the [
• (
BEEP)]
 key to store the current channel.
4. Rotate the DIAL knob to set the cursor to the “END” menu selection, then press the
[
ENT(
SET)]
 key.
5. Confirm that the cursor is on...

VR-5000 OPERATING MANUAL28
MEMORY CHANNEL SORT
The VR-5000 can also sort the memory channels according to “Alpha-Numeric Name
Ta g,” “Frequency,” “Receive mode,” or “Channel Number.” When this is done, the
memory channel numbers will be re-arranged to reflect the new lineup of the memorized
channels.
Sorting by Alpha-Numeric Name Tag:
1. Recall the Memory mode.
2. Press the [
M/S(
SUB SET)]
 key, then rotate the DIAL knob to set the cursor to the
“TAG NAME” menu.
3. Press the [
• (
BEEP)]
 key to set the...