Xerox WorkCentre Pro 133 User Manual

							Copy Mode Settings 
Xerox CopyCentre/WorkCentre/WorkCentre Pro 123/128/133 User Guide 211
1.Select [Reduce/Enlarge 
Presets] on the [Copy Mode 
Settings] screen.
2.Use the scroll buttons to switch 
between screens.
3.Perform the necessary 
operations.
4.Select [Close].
R/E Preset 1–7
Allows you to assign your choice of magnifications to each of the seven buttons within 
the range of 25–400% by selecting from 25 options.
Downloaded From ManualsPrinter.com Manuals 
						

							11 Setups 
212 Xerox CopyCentre/WorkCentre/WorkCentre Pro 123/128/133 User Guide
Network Settings
This screen allows you to change the default settings for the network configuration. 
There are eight main setup options available. For more information, refer to the 
following.
NOTE: Items shown in these setting screens may vary depending on a usage 
environment.
For more information on network setups, refer to the System Administration Guide.
Port Settings – page 212
Protocol Settings – page 215
Machine E-mail Address/Host Name – page 216
POP3 Server Settings – page 217
SMTP Server Settings – page 218
Domain Filter – page 219
Remote Authentication Server Settings – page 219
Other Settings – page 220
1.Select [Network Settings] on the 
[System Settings] screen.
2.Select the required option.
3.Select [Close].
Port Settings
This feature allows you to set print mode, port status, communication mode, auto eject 
time for each communication port.
1.Select [Port Settings] on the 
[Network Settings] screen.
2.Perform the necessary 
operations.
3.Select [Close].
Parallel
Use this feature to specify whether to enable the parallel port and to configure the 
relative parameter settings.
Port Status
Specify whether to enable the parallel port.
Downloaded From ManualsPrinter.com Manuals 
						

							Network Settings 
Xerox CopyCentre/WorkCentre/WorkCentre Pro 123/128/133 User Guide 213
Print Mode
Specify the PDL (Page Description Language) to be used for print jobs. Only pre-
installed PDLs are available.
PJL
Specify whether to enable the PJL (Printer Job Language).
Auto Eject Time
Specify the time-out period when print data is not sent to the machine sequentially. If 
the specified time elapses, the remaining data inside the machine is automatically 
printed out. You can specify a time within the range of 5–1,275 seconds in 5-second 
increments.
Adobe Communication Protocol
Specify the communication protocol format for Adobe Communication Protocol.
• Standard – Select this option when the communication protocol is in the ASCII 
format.
• Binary – Select this option when the communication protocol is in the binary format. 
Depending on the data, the print job may be completed faster than [Standard].
• TBCP – (Tagged Binary Communications Protocol) Select this option to switch the 
specific control codes when the communication protocols involve both ASCII and 
binary formats.
Bi-directional Communication
Select whether to enable the bi-directional communication.
Input Prime
Select whether to enable the input prime. If enabled, the reset processing is triggered 
by the input prime signal received.
USB
Use this feature to specify whether to enable the USB port and to configure the relative 
parameter settings.
Port Status
Specify whether to enable the USB port.
Print Mode
Specify the PDL to be used for print jobs. Only pre-installed PDLs are available.
PJL
Specify whether to enable the PJL (Printer Job Language). 
Downloaded From ManualsPrinter.com Manuals 
						

							11 Setups 
214 Xerox CopyCentre/WorkCentre/WorkCentre Pro 123/128/133 User Guide
Auto Eject Time
Specify the time-out period when print data is not sent to the machine sequentially. If 
the specified time elapses, the remaining data inside the machine is automatically 
printed out. You can enter a time within the range of 5–1,275 seconds in 5-second 
increments.
Adobe Communication Protocol
Specify the communication protocol format for Adobe Communication Protocol.
• Standard – Select this option when the communication protocol is in the ASCII 
format.
• Binary – Select this option when the communication protocol is in the binary format. 
Depending on the data, the print job may be completed faster than [Standard].
• TBCP – Select this option to switch the specific control codes when the 
communication protocols involve both ASCII and binary formats.
LPD
Use this feature to specify whether to enable the LPD port.
NetWare
Use this feature to specify whether to enable the NetWare port.
SMB
Use this feature to specify whether to enable the SMB port.
IPP
Use this feature to specify whether to enable the IPP port.
EtherTalk
Use this feature to specify whether to enable the EtherTalk port.
Salutation
Use this feature to specify whether to enable the Salutation port. This setting item is 
available only when the hard disk is installed on the machine.
Port9100
Use this feature to specify whether to enable the Port9100 port.
SNMP
Use this feature to specify whether to enable the SNMP agent.
FTP Client
Use this feature to specify whether to enable the FTP Client port. This setting item is 
available only when the hard disk is installed on the machine.
Downloaded From ManualsPrinter.com Manuals 
						

							Network Settings 
Xerox CopyCentre/WorkCentre/WorkCentre Pro 123/128/133 User Guide 215
Receive E-mail
Use this feature to specify whether to enable the mail receiving port.
Send E-mail
Use this feature to specify whether to enable the mail transmission port.
Mail Notice Service
Use this feature to specify whether to enable the mail notification service.
UPnP Discovery
Use this feature to specify whether to enable the UPnP port.
Internet Services (HTTP)
Use this feature to specify whether to enable the Internet Services port.
Port Status
Specify whether to enable the Internet Services port.
Internet Services Port Number
Specify the port number for Internet Services from 0, 80, or any port from 8000 to 9999.
Protocol Settings
This feature allows you to configure the machine settings that correspond with the 
protocol being used.
1.Select [Protocol Settings] on the 
[Network Settings] screen.
2.Perform the necessary 
operations.
3.Select [Close].
Ethernet Setting
Specify the Ethernet port speed according to the network environment to which the 
machine is connected.
TCP/IP - Get IP Address
Specify the method of obtaining an IP address for the machine.
TCP/IP - IP Address
Allows you to enter the IP address in the form of vvv.xxx.yyy.zzz. The IP address entry 
is required when selecting [Manual] on the [TCP/IP - Get IP Address] screen.
Downloaded From ManualsPrinter.com Manuals 
						

							11 Setups 
216 Xerox CopyCentre/WorkCentre/WorkCentre Pro 123/128/133 User Guide
TCP/IP - Subnet Mask
Allows you to enter the subnet mask in the form of vvv.xxx.yyy.zzz.
TCP/IP - Gateway Address
Allows you to enter the gateway address in the form of vvv.xxx.yyy.zzz.
TCP/IP - IP Filter
Specify whether to restrict the remote machines which send print jobs using LPD.
HTTP - SSL/TLS Communication
Specify whether to enable the SSL/TLS communication.
HTTP - SSL/TLS Port Number
Allows you to enter the port number for the SSL/TLS communication within the range 
of 443, 8000–9999.
Machine E-mail Address/Host Name
This feature allows you to set e-mail address, host name, or domain name for the 
machine.
1.Select [Machine E-mail 
Address/Host Name] on the 
[Network Settings] screen.
2.Perform the necessary 
operations.
3.Select [Close].
E-mail Address
Allows you to enter the e-mail address of the machine up to 128 characters.
Host Name
Allows you to enter the host name of the machine up to 64 characters.
Domain Name
Allows you to enter the domain name of the machine up to 64 characters.
Downloaded From ManualsPrinter.com Manuals 
						

							Network Settings 
Xerox CopyCentre/WorkCentre/WorkCentre Pro 123/128/133 User Guide 217
POP3 Server Settings
This feature allows you to set up the POP3 server settings, such as port number, IP 
address, server name, and password.
1.Select [POP3 Sever Settings] on 
the [Network Settings] screen.
2.Perform the necessary 
operations.
3.Select [Close].
POP3 Server Setup
Select the method of specifying the POP3 server.
POP3 Server IP Address
Allows you to enter the IP address of the POP3 server in the form of vvv.xxx.yyy.zzz. 
This entry is required only when selecting [By IP Address] on the [POP3 Server Setup] 
screen.
POP3 Server Name
Allows you to enter the POP3 server name in the style of FQDN within a maximum of 
64 characters. This entry is required only when selecting [By Server Name] on the 
[POP3 Server Setup] screen.
POP3 Server Port Number
Allows you to enter the port number for the POP3 server communication within the 
range of 1–65535.
POP3 Server Check Interval
Allows you to enter the interval to poll the POP3 server within the range of 1–120 
minutes in 1-minute increments.
POP3 Server Login Name
Allows you to enter the user name used to log in to the POP3 server up to 64 
characters.
POP3 Server Password
Allows you to enter the password used to log in to the POP3 server up to 36 characters.
POP Password Encryption
Allows you to specify whether or not to encrypt the log-in password using APOP.
Downloaded From ManualsPrinter.com Manuals 
						

							11 Setups 
218 Xerox CopyCentre/WorkCentre/WorkCentre Pro 123/128/133 User Guide
SMTP Server Settings
This feature allows you to set up the SMTP server settings, such as port number, IP 
address, server name and a password.
1.Select [SMTP Sever Settings] 
on the [Network Settings] 
screen.
2.Perform the necessary 
operations.
3.Select [Close].
SMTP Server Setup
Select the method of specifying the SMTP server.
SMTP Server IP Address
Allows you to enter the IP address of the SMTP server in the form of vvv.xxx.yyy.zzz. 
This entry is required only when selecting [By IP Address] on the [SMTP Server Setup] 
screen.
SMTP Server Name
Allows you to enter the SMTP server name in the style of FQDN within a maximum of 
256 characters. This entry is required only when selecting [By Server Name] on the 
[SMTP Server Setup] screen.
SMTP Server Port Number
Allows you to enter the port number for the SMTP server communication within the 
range of 1–65535.
E-mail Send Authentication
Allows you to specify the authentication method for the SMTP server communication. 
If you select [POP before SMTP], the POP server authentication is required before 
transmitting e-mails to the SMTP server. If you select [SMTP AUTH], the SMTP server 
authentication is enabled.
SMTP AUTH Login Name
Allows you to set the user name used to log in to the SMTP server up to 64 characters. 
This entry is required if [SMTP AUTH] is selected on the [E-mail Send Authentication] 
screen.
SMTP AUTH Password
Allows you to set the password used to log in to the SMTP server up to 36 characters. 
This entry is required if [SMTP AUTH] is selected on the [E-mail Send Authentication] 
screen.
Downloaded From ManualsPrinter.com Manuals 
						

							Network Settings 
Xerox CopyCentre/WorkCentre/WorkCentre Pro 123/128/133 User Guide 219
Domain Filter
This feature allows you to restrict incoming e-mails by registering domain names of 
senders.
1.Select [Domain Filter] on the 
[Network Settings] screen.
2.Perform the necessary 
operations.
3.Select [Close].
Domain Filtering
Allows you to select the restriction method, either [Enter Permitted Domain Names] or 
[Enter Rejected Domain Name]. If [Off] is selected, this feature is disabled.
Domain 1–50
Allows you to enter domain names to be restricted or permitted according to the 
selection on the [Domain Filtering].
Remote Authentication Server Settings
This feature allows you to set up the external authentication server settings.
1.Select [Remote Authentication 
Server Settings] on the [Network 
Settings] screen.
2.Perform the necessary 
operations.
3.Select [Close].
Authentication System
Allows you to select the remote authentication service.
Remote Server Setup
Select the method of specifying the KDC (Key Distribution Center) server.
Remote Server IP Address
Allows you to enter the IP address of the KDC server in the form of vvv.xxx.yyy.zzz.
Remote Server Name
Allows you to enter the KDC server name in the style of FQDN within a maximum of 
255 characters.
Downloaded From ManualsPrinter.com Manuals 
						

							11 Setups 
220 Xerox CopyCentre/WorkCentre/WorkCentre Pro 123/128/133 User Guide
Remote Server Port Number
Allows you to enter the port number for the KDC server communication within the range 
of 1–65535.
Remote Server Realm Name
Allows you to enter the KDC realm name within a maximum of 64 characters.
Other Settings
This feature allows you to select the e-mail receiving protocol from either SMTP or 
POP3.
1.Select [Other Settings] on the 
[Network Settings] screen.
2.Perform the necessary 
operations.
3.Select [Close].
E-mail Receive Protocol
Allows you to select the protocol for receiving e-mail.
Print Mode Settings
This screen allows you to change the default settings for the printer configuration. For 
more information, refer to the following.
NOTE: Key Operator access is required for this feature.
Allocate Memory – page 221
Other Settings – page 223
1.Select [Print Mode Settings] on 
the [System Settings] screen.
2.Select the required option.
3.Select [Close].
Downloaded From ManualsPrinter.com Manuals