Xerox WorkCentre 3045 Service Manual

Phaser 3010/3040/WorkCentre 3045 Service Xerox Internal Use Only 5-53Parts Lists
Parts List 8.2 Scanner / Control Panel
Item Name Part Number
1 Scanner Assy (with 2,8,10-12) (3045B) 604K70931
2 Document Cover (with 7) (3045B)
3- -
4- -
5- -
6- -
7 Hinge Assy ADF TBD
8 IIT Assy (with 9)
9Speaker
10 Control Panel (3045B)
11 Cover SSB
12 Rail IIT FB
13 Control Panel Board TBD
14 Control Panel LCD Display TBD 

5-54 Xerox  Internal  Use  Only Phaser 3010/3040/WorkCentre 3045 Service  Parts Lists
Xerox Supplies and Accessories
Hardware Kit 
Hardware Kit
DescriptionPart Number
Hardware Kit 604K60070
Screw For Plastic, Tapping - ST1
Screw For Plastic, Tapping - ST4
Screw For Plastic, Tapping W/flange ST-10
Screw For Metal Sheet SM2 

6
Chapter
Maintenance
In this chapter...
• Adjusting the Transfer Roller
•Adjusting the Fuser 
• Adjusting Altitude 

6-2 Xerox  Internal  Use  Only Phaser 3010/3040/WorkCentre 3045 Service  Maintenance
Service Maintenance Procedure
Perform the following procedures whenever you check, service, or repair a printer. 
Cleaning the printer, as outlined in the following steps, assures proper operation of 
the printer and reduces the probability of having to service the printer in the 
future.
The frequency of use, the type of media printed on, and operating environment 
are factors in determining how critical cleaning the...

Phaser 3010/3040/WorkCentre 3045 Service Xerox Internal Use Only 6-3Maintenance
Cleaning the Platen and Document Cover
Use a dry, lint-free cloth to lean the platen glass and document cover.
s3040-164
s3040-165 

6-4 Xerox  Internal  Use  Only Phaser 3010/3040/WorkCentre 3045 Service  Maintenance
Moving the Printer
The printer, with toner installed, weighs 11.3 kg (24.9 lb.).
Caution
When moving the printer over long distances, remove the Toner Cartridge to 
prevent toner spills.
Before moving the printer, do the following:
1. Turn the printer Off and disconnect all cables.
2. Allow the printer to cool about 40 minutes.
3. Remove media from the output tray and return the Tray Extension to its non-
extended...

Phaser 3010/3040/WorkCentre 3045 Service Xerox Internal Use Only 6-5Maintenance
Adjusting the Transfer Roller
The bias voltage applied to the Transfer Roller (BTR) controls how the toner 
transfers from the drum to the paper. The bias is set for each paper type that is 
selected and used in the printer. If the bias voltage is too low, the toner does not 
transfer properly, producing light colors and white spots. If the bias voltage is too 
high, mottling of the image can occur.
To  a d j u s t  t h e  BT...

6-6 Xerox  Internal  Use  Only Phaser 3010/3040/WorkCentre 3045 Service  Maintenance
Adjusting Altitude
Print quality varies with barometric pressure. Since the barometric pressure 
decreases as the altitude increases, altitude can affect the print quality. To 
optimize print quality for your location, select an altitude setting to match the 
your location.
To adjust altitude:
1. On your computer, click Start > All Programs > Xerox Office Printing > Phaser 
3010/3040 > Printer Setting Utility.
2. Click...

Phaser 3010/3040/WorkCentre 3045 Service Xerox Internal Use Only 6-7Maintenance
Scanner Adjustment
When the Scanner or IP Board are replaced, adjust the Scanner. The WorkCentre 
3045 has a Gap Serial Number sticker located at the center rear of the scanner. 
Use this number to adjust the scanner.
1. Connect the printer to the computer via USB.
2. Start the Grande Gap Writer software.
3. Choose the scanner from the Scanner List.
4. Enter the Gap Serial Number in the Gap SN box and press Enter. The...

6-8 Xerox  Internal  Use  Only Phaser 3010/3040/WorkCentre 3045 Service  Maintenance