Wolf Cinema Projector Dcx 1500fd User Manual

4-6
Section	4	►	Maintenance
noTe: The lamp mode you choose to run the projector in may have an impact on t\
he number 
of hours expected for the lamp.
Tools required: #2 Phillips screwdriver 
WaRnIngs
     A qualified service technician must perform lamp replacement.
    Cool the lamp completely and handle by the housing only.
   Install the correct wattage lamp supplied by Wolf Cinema (see above) and read the   
   lamp Replacement procedure in its entirety before proceeding. 
    Do  not  touch  the...

4-7
Section	4	►	Maintenance
4. Release The laMP loCK
  Pull out and turn the lamp lock lever, which is located to the left of the lamp module, and turn 
it ¼ turn counter clockwise to the “unlock” position. See Figur\
e 4.3.
5.  ReMoVe The laMP MoDUle
  Firmly grasp the lamp by its housing only and pull it straight out (lamp slides along guides) 
until it is free. See Figure 4.4. Discard the lamp using safe disposal/r\
ecycling practices.
6.  InseRT The neW laMP MoDUle
  Align the new lamp with the top...

4-8
Section	4	►	Maintenance
7.  loCK In The neW laMP MoDUle
 Pull out and turn the lamp lock lever (turned up in Step 4) ¼ turn clockwise to “lock” the lamp 
in place. 
  noTe:  If you can’t turn the lamp lock into position, it is likely the lamp is not fully inserted. In 
this case, partially remove the lamp and try pushing it back in again. Then, try switching the 
lock lever to the “lock” position.
8.  RePlaCe The laMP DooR
  Replace the lamp door and secure it with the two (2) screws removed in\...

4-9
A	variety	 of	lenses	 can	accommodate	 different	throw	distances	 and	specific	 types	of	installations.	
Refer	 to	Section	 6	-	Specifications	 for	details.	 To	change	 a	lens,	 follow	 the	steps	 below.	 No	tools	
are required for “compact” lenses shown.
TURn off The PRojeCT oR, Cool anD UnPlUg
noTe: If necessary, a lens can be swapped out while the projector is running, but this can result 
in dust being drawn into the projector. Avoid if possible. 
Before removing or installing any lens, turn off...

4-10
Section	4	►	Maintenance
sTeP 3 sTeP 4 
sTeP 5 RoT aTe The lens  
Rotate  the  lens  counter-
clockwise  until  the  tabs  are 
free from the lens retainer ring. 
See Figure 4.8A.
noTe:  The  connector  slide 
assembly allows the connector 
to move as the lens is rotated.
PUll lens oUT
Lens connectors will disconnect 
when you pull the lens straight 
out  from  the  projector.  See 
Figure 4.8B.
InseRT neW lens
noTe: Remove small rear cap! Keep front cap on.
Electrical connector:
•   Line up male...

5-1
seCTIon 5
sPeCIfICaTIons
DCx-500i DCx-500fD
light engineCinema Contrast three chip DLP™ light engine Cinema Contrast three chip DLP™ light engine
Color filter Filmic Color Correction Filter Filmic Color Correction Filter
lamp Xenon lamp 500W Xenon lamp 500W
lens system VariScope constant height lens system VariScope constant height lens system
lens options 
†.67:1** RP lens
1.1:1** FP lens
1.45-1.8:1* 1.86-2.58:1*
2.65-4.0:1*
4.5-6.7:1*.67:1** RP lens
1.1:1** FP lens
1.45-1.8:1*1.86-2.58:1*...

5-2
DCx-1000iDCx-1000fD
light engineCinema Contrast three chip DLP™ light engine Cinema Contrast three chip DLP™ light engine
Color filter Filmic Color Correction Filter Filmic Color Correction Filter
lamp Xenon lamp 1000W Xenon lamp 1000W
lens system VariScope constant height lens system VariScope constant height lens system
lens options 
†.67:1** RP lens
1.1:1** FP lens
1.45-1.8:1* 1.86-2.58:1*
2.65-4.0:1*
4.5-6.7:1*.67:1** RP lens
1.1:1** FP lens
1.45-1.8:1*1.86-2.58:1*
2.65-4.0:1*
4.5-6.7:1*
gamma...

5-3
DCx-1500iDCx-1500fD
light engineCinema Contrast three chip DLP™ light engine Cinema Contrast three chip DLP™ light engine
Color filter Filmic Color Correction Filter Filmic Color Correction Filter
lamp Xenon lamp 1225W Xenon lamp 1225W
lens system VariScope constant height lens system VariScope constant height lens system
lens options 
†.67:1** RP lens
1.1:1** FP lens
1.45-1.8:1* 1.86-2.58:1*
2.65-4.0:1*
4.5-6.7:1*.67:1** RP lens
1.1:1** FP lens
1.45-1.8:1*1.86-2.58:1*
2.65-4.0:1*
4.5-6.7:1*
gamma...

A-1
aPPenDIx a
KeYPaD RefeRenCe
noTe:  The IR remote is a standard component provided with the projector. Use the extension 
cable also provided to convert the IR remote to a wired remote, if desired.  Refer to  Section 3 for 
a specific description of each key and how to use them correctly.
* Toggle keys, which require you to either, press and hold, or press twice or press and use the 
up/down arrow key. 
Press and hold  to toggle or press twice to toggle or press and release, followed by ▲ ON or ▼ OFF...

B-1
A serial link of RS232 or RS422 enables ASCII communication with the projector so that it can 
be controlled remotely from a PC or other controller. From a PC, connect a standard nine-wire 
RS232  serial  cable  to  the Rs232  In  port.  Or,  for  long-distance  (>100  ft.)  links  with  an  RS422-
compatible PC or controller, connect RS422 cable to the  Rs422 port.
aPPenDIx b
seRIal  CoMMUnICa TIons