Whirlpool Wv 1843 A Nfx Product Sheet

							
GBPRODUCT SHEET
1.Compartment for freezing
2. Control unit
3. Area for drawers and pull-out baskets
4. Rating plate (inside
the appliance)
5. Ice packs (inside - if provided)
Note: the design of drawers and accessories may vary, depending on the model.
Controls  (depending on model)
ADigital temperature display.
B Yellow LED: indicates that the fast freeze 
function is in operation.
C Red LED: blinks to indicate that the temperature 
in the freezer compartment is too high.
D Freezer on/off button. E
Internal temperature control.
F Fast freeze button.
G Acoustic alarm mute button.
H
Switching on
Storage compartment
Area for freezing
1. Plug in the appliance.
Attention If the digital display shows only 
an illuminated dot, press the 
freezer on/off button  D. Six horizontal lines appear on the digital 
display.
After about 3 seconds, 
when the appliance is 
warm, (internal temperature above 10°C) 
only the two lines in the middle remain 
illuminated; The acoustic alarm and red LED 
C  are activated.
2. Press button  G to mute the 
acoustic alarm. The acoustic alarm stops while the red LED 
continues to blink.
3. Wait until the temperature 
indicated on the digital display 
reaches -12°C. When the temperature reaches -12°C, the 
red LED automatically stops blinking.
4. Place food to be frozen and/or 
already frozen food in the 
freezer.
“6th Sense”/“Dynamic Intelligence” activation LED
(blue), (if provided).
Indicates that the “6th Sense”/“Dynamic Intelligence”
function is (see paragraph “6th Sense”/“Dynamic
Intelligence” function).
5019 608 01058
 
						

							
DFNLEPGRDKSNFINIGB
PRODUCT SHEET
Freezer compartment temperature adjustment
The appliance is normally factory set for optimum operation at a temperature of -18°C.
To alter the internal temperature between -16°C and -24°C, proceed as follows:
• Press button  E once to adjust the internal temperature: the  digital display shows the temperature previously 
set.
• Each time the button is pressed, the temperature setti ng is changed by 1°C: the value (between -16°C and 
-24°C) blinks cyclically on the display.
• Approximately 5 seconds after the button has been pressed for the last time, the set temperature is stored, 
the display stops blinking and the current in ternal temperature is shown on the display.
•
Note:
The digital display shows internal temp erature values between +10°C and -24°C.
In the event of a power failure, selected  functions remain stored in the memory.
Fast freezingThe fast freeze function switches off automatically when freezing is complete.
Alarm signals
Note:
The temperature alarm may activate if the door is left  open for a prolonged period of time or following the 
introduction of fresh food in the freezer compartment;  this temporary rise in temperature does not affect the 
storage of already frozen food in any way.
Defrosting (for No Frost mode ls no operation is required)
This appliance defrosts automatically according to usage and ambient humidity conditions.
Follow the steps detailed in “Switching on the appliance”.
For not No Frost models, follow step 1-6:
Signal Cause Solution
Door open alarm
The acoustic alarm is activated T he door has been left open 
for more than 1 minute Close the door
Temperature alarmThe acoustic alarm and red LED 
C 
are activated The internal temperature is 
above -12°CPress button 
G; wait for 
the temperature to fall 
below -12°C again
Te m p e r a t u r e  s e n s o r  
alarmThe acoustic alarm is activated and 
the display shows  “SF”Temperature sensor fault Contact After-sales 
service
Prolonged power failure 
alarmThe acoustic alarm and red LED  C 
are activated; the display blinks, 
indicating the highest temperature 
reached following the power failure Prolonged lack of power 
supply, causing the internal 
temperature to rise to very 
high values at which correct 
food storage cannot be 
guaranteedPress button 
G; the 
display now indicates the 
current internal 
temperture
1. Press the freezer on/off button  D. An illuminated dot appears on the digital display.
2. Unplug the appliance or  switch off at the main 
switch.
3. Fit the drain in place (see figure).
4. Follow the instructions given in the 
instructions booklet.
5. Plug in the appliance once again.
6. Press the freezer on/off button  D. Follow the steps detailed  in “Switching on the 
appliance”.
The 6th Sense/“Dynamic Intelligence” function (blue LED) is auto\
matically activated due to door opening and
when small amounts of fresh food are placed in the freezer. The duration of the 6th Sense function varies
depending on the quantity of food loaded in the freezer and ambient temp\
erature. When optimal operating
conditions have been restored the function deactivates automatically and\
 no operation is required.
5019 608 01058Printed in Italy  03/09