Whirlpool Wte 3322 Nfs Product Sheet

							A. Refrigerator Compartment
1.Filter in the fan
2.Electronic control panel / light unit
3.Shelves / Shelf area
4.Multi-flow cold air system
5.Cooler compartment
6.Rating plate with commercial name
7.Fruits and vegetables crisper
7a.Crisper divider
8.Egg tray
9.Reversibility kit
10.Separator
11.Door trays
B. Freezer Compartment 
12.Area for freezing (with/without flap)
13.Area for storing frozen foods
14.Ice tray
15.Plastic shelf
16.The freezer door trays for pizza or other frozen
products with a short storage time (2** storage
compartment)
17.Door seals
Depending on the model the number and type of
accessories may vary.
Anti-bacterial protection (depending on the model):
- Antibacterial filter in the fan (1)
- Antibacterial  additives in the Crisper (7)
- Door seals from materials that inhibit bacterial growth
(17).
Notes:
- In case itll have a flap, please remember that to
maximize the storage volume its suggested to remove it.
- All shelves and door trays are removable. Freezer plastic
shelf cannot be removed to have a good air flow rate
inside freezer compartment.
- The internal temperatures of the appliance depend on
the ambient temperature, frequency of opening the
doors, as well as location of the appliance. Temperature
setting must consider these factors.
- The appliance accessories are not suitable for washing in
dishwasher.
HOW TO START THE APPLIANCE
Fit the spacers (if supplied) on
the upper part of the condenser
at the rear of the appliance.
After plugging the appliance to
the mains, it starts the operation
automatically.
After starting the appliance, wait at least 4-6 hours before
placing food into the appliance .
The indicator LEDs on the control panel light up for
approximately 1 second, and after initialization process,
setpoint is displayed.
Note:
- If food is placed in the refrigarator before the appliance
has cooled completely, it may deteriorate.
- If fresh food is loaded in freezer position 3 on control
panel should be chosen.
FAN WITH A BUTTON
The fan improves temperature distribution inside the
refrigerator compartment, allowing better preservation of
stored food.
To switch on the fan press the button (1a). It is advisable
to activate the fan when the ambient air temperature is
over 27 ÷ 28°C or if you perceive drops of water on the
glass shelves or in the severe humidity conditions.
Note:
Do not obstruct the air intake area with food items.
The fan will run ONLY when the compressor is in
operation.
Remember to turn off the fan when there is a lower
ambient air temperature.
If the appliance has the fan it can be equipped with the
antibacterial filter.
Remove it from the box (found in the crisper drawer
(item 7) and insert into the cover of fan (item 1b).
The replacement procedure is attached with the filter.
ELECTRONIC CONTROL PANEL
DESCRIPTION
1.extra low temperature Fast
cooling
2.high temperature
3.medium temperature
4.low temperature
5.temperature selection/Fast
cooling (3 sec. minimum)
pushbutton
ROBGRUSHSKCZPLIGBFINDKNSGRPENLFD
PRODUCT SHEETGB
 
						

							OPERATION DESCRIPTION
Temperature adjustment is made with pushbutton (item 5).
Temperature setpoint is done for both compartments at
one time – fridge and freezer.
At first plug-in of appliance factory setpoint is chosen –
medium position (item 3).
Following table shows set-points level
Description:
LED OFF
LED ON
GUIDE TO SELECTING FUNCTIONS
Temperature selectionpushbutton (item 5) is used to
set desired temperature level, from coldest  to
warmest  . At each short pressure of the
pushbutton, the setpoint will change (cyclically).
Fast Coolingfunction 
The use of this function is recommended when placing a
very high quantity of food in the refrigerator
compartment.
By pressing  and hold the button (item 5) for 3 sec. it is
possible to increase the cooling speed of the foods inside
the refrigerator compartment. The yellow LED (item 1)
will come on. The function is automatically deactivated
after 6 hours.
The Fast cooling function can be manually deactivated by
pressing and hold the same button (item 5) for 3 sec., the
yellow LED (item1) is off.
Note:
- Fast Cooling function should be also switched ON
before placing fresh food to be frozen in  the freezer
compartment.
- Fast Cooling function has to be engaged in order to
maximize freezing capacity, thus it has to be engaged
before to add light load.
ABNORMAL APPLIANCE OPERATION
When the product is plugged in to the mains, during first
10 minutes of its performance, possible temperature
sensor failure will be displayed according to following
table:
Description:
LED OFF
LED Flashing
The appliance will work preserving the food stored, but it
is necessary to contact after-sales service and provide
alarm code.
Note:in case of power failure, appliance goes back to
normal operation and previously chosen setpoint is
restored.
DEFROSTING THE FREEZER
COMPARTMENT
No Frostfreezers provide chilled air circulation around
the storage areas and prevent the formation of ice,
thereby completely eliminating the need for defrosting.
Frozen items dont stick to the walls, labeling stays legible
and storage space remains neat and clear. 
DEFROSTING THE REFRIGERATOR
COMPARTMENT
Refrigerator compartment defrosting is completely
automatic.
Droplets of water on the rear wall inside the refrigerator
compartment indicate that the automatic defrost phase is
in progress. The  defrost water is automatically run into a
drain hole and collected in a container, where it
evaporates.
REPLACING THE LIGHT BULB
Always disconnect the refrigerator from the power supply
before replacing any light bulb.
If the inside light is not working, it is necessary to:
1.Remove the light cover:
move it upwards as
shown in figure.
2.Check the bulb. If
necessary unscrew the
broken bulb and replace
it with the new one.
3.Put on the light cover. 
Do not leave the bulb uncovered.
5019 636 01009
Printed in Poland  04/10
ROBGRUSHSKCZPLFINDKNSGRIPENLFGBD
PRODUCT SHEETGB
Refrigerator
evaporator sensor
failureRefrigerator sensor
failureRefrigerator
evaporator &
refrigerator sensor
failure