Whirlpool AWG 310 D User Manual

							GB 11
Description of red indications
The red light 
will go on 
(if fitted to the 
appliance)Alphanumeric 
indications shown 
on the display 
(on models fitted 
with them)Description
Cause
Solutions
“Water Tap 
Closed”E00The appliance has insufficient or no water supply. 
The 
“Start” light goes on.
Check that:
The water tap is fully open and the water pressure 
is sufficient.
The water supply hose is kinked.
the mesh filters of the water supply could be 
blocked (see “Care and maintenance”.
The water hose is frozen up.
When the problem has been resolved, re-start the 
programme by pressing the 
“Start” button. If the 
fault occurs again, contact the After-Sales Service 
[see next chapter).
“Clean Pump”E01The water is not pumped out of the washing 
machine. The appliance stops in mid programme; 
unplug the appliance and check if:
there are kinks in the drain hose.
the filter or pump is blocked (see chapter 
“Removing The Filter/Draining Residual Water”; 
make sure the water has cooled before 
draining the appliance).
the water in the water inlet hose is frozen.
When you have resolved the problem, turn the 
programme selector to “Off/O” to reset the 
appliance; next re-start the desired programme. If 
the fault occurs again, contact the After-Sales 
Service [see next chapter).
“Electrical module fault”
“Service”
Door locking error E02
E03Unplug the appliance and turn the programme 
selector to 
“Off/O”, then turn the appliance ON 
again. Select the “Drain/Spin” programme and re-
start within 15 seconds.
“Fod”
E04Turn the appliance OFF by turning the programme 
selector to 
“Off/O”; Open and close the door again 
with more force then reselect the programme and 
press 
“Start”. 
If any of the faults described above persists, unplug 
the appliance, turn off the water supply and contact 
our After-Sales Service (see next chapter).
30120034GB.fm  Page 11  Thursday, January 8, 2009  4:24 PM
Black process 45.0° 150.0 LPI 
 
						

							GB 12
AFTER-SALES SERVICE
Before contacting After-Sales Service:
1.Try to remedy the problem yourself (see 
“Troubleshooting Guide”).
2.Restart the programme to check whether the 
problem has solved itself.
3.If the washing machine continues to function 
incorrectly, call After Sales Service.Specify:
The nature of the problem.
The washing machine model.
The service code (number after the word 
SERVICE)
The After Sales Service sticker can be found 
inside the door.
Your full address.
Your telephone number and area code.
After-Sales Service phone numbers and 
addresses are given on the guarantee card. 
Alternatively, consult the dealer where you 
purchased the appliance.
ACCESSORIES
For some models, you can obtain accessories from 
our After-Sales Service or from an authorised 
dealer:
a 
Pedestal Drawer which can be installed 
beneath your washing machine It raises your 
machine to allow for more comfortable loading 
and unloading, as you now no longer need to 
bend as far to access the unit. Furthermore, it 
offers a great space-management tool and 
storage solution.
a 
Stacking Kit by means of which you can fix 
your dryer on top of your washing machine and 
thus effectively save space.Some models are able to be installed under your 
kitchen worktop; in that case, please contact our 
After-Sales Service (see above). Attention:
the appliance MUST be installed under a 
continuous worktop.
according to the legal safety regulations, the 
installation of the appliance MUST be carried out 
by an authorized technician or by our After-Sales 
Service.
the appliance MUST be installed using the 
intermediate cover panel of the 
UBS Base Set 
which can be obtained from specialist dealers or 
our After-Sales Service.
30120034GB.fm  Page 12  Thursday, January 8, 2009  4:24 PM
Black process 45.0° 150.0 LPI 
 
						

							GB 13
BUILT-IN MODELS
INSTALLATION TIPS
Washer dryer housing dimensions:
Due to the need for the washer dryer filter to be cleaned periodically the plinth should be easily 
removable.
For easy care and maintenance water supply and drain should not be positioned behind the appliance.
The electrical connections should be positioned so that the appliance can be disconnected when fitted in 
position.
30120034GB.fm  Page 13  Thursday, January 8, 2009  4:24 PM
Black process 45.0° 150.0 LPI 
 
						

							GB 14
FITTING A DÉCOR DOOR TO THE APPLIANCE
The appliance front part has been fitted to accommodate the hinges so that the door can be opened either 
from the left or from the right hand side.
Proceed as follows:
1.Screw the hinges onto the décor door, if a dummy drawer front is also being used ensure it to be fastened 
to the top edge of the door. Ensure the gap between door and drawer matches the units either side.
2.Fix the two hinge plates to the front of the washer dryer using the two plastic backing pieces.
Note: an 8mm box spanner can be used to screw the thread cutting screws into position.
3.Fasten the two magnetic catches to the opposite side to the hinges and ensure the metal straps are 
fastened to the back of the door.
4.Locate the hinges on the door into the two hinge plates on the appliance.
5.If adjustment is necessary this can be achieved by either the hinge plates (vertical) or by the hinge fixing 
screws (horizontal).
FITTING A FULL HEIGHT DOOR
If a full height door is to be fitted (no dummy drawer front is being used) a top hinge hole has to be drilled 
in the door.
The distance between the two hinge hole centres is 360 - 384mm and the distance from the edge of the 
door is 21.5mm.
The hinge hole should be max 12mm deep and its diameter 35mm: make sure you do not drill through the 
door.
The two fixing holes for the hinge screws are 2mm.
DÉCOR STRIP
A décor strip can be screwed into position on the edge of the washer dryer. If needed, the strip can be cut 
to be adjusted to your furniture but normally this will not be necessary.
TO LINE UP
TO DRILL
30120034GB.fm  Page 14  Thursday, January 8, 2009  4:24 PM
Black process 45.0° 150.0 LPI