Whirlpool ARC 1800 AL Manual

							14
INSTRUCTIONS FOR USE
BEFORE USING THE APPLIANCE
SAFEGUARDING THE ENVIRONMENT
PRECAUTIONS AND GENERAL 
RECOMMENDATIONS
HOW TO OPERATE THE REFRIGERATOR 
COMPARTMENT
HOW TO OPERATE THE FREEZER 
COMPARTMENT
HOW TO DEFROST AND CLEAN THE 
FREEZER
HOW TO CLEAN THE REFRIGERATOR 
COMPARTMENT
CLEANING AND MAINTENANCE
TROUBLESHOOTING GUIDE
AFTER-SALES SERVICE
INSTALLATION
DOOR REVERSIBILITY
ELECTRICAL CONNECTION
63602029GB.fm  Page 14  Wednesday, October 24, 2007  5:17 PM
 
						

							15
BEFORE USING THE APPLIANCE
SAFEGUARDING THE ENVIRONMENT
•
Your new appliance is designed exclusively for 
domestic use.
To get the most out of your new appliance, 
read the user handbook carefully. It 
contains a description of the appliance as 
well as useful tips. 
Keep this handbook for future consultation.1.
After unpacking the appliance, make sure that 
it is undamaged and that the doors close 
correctly. Any damage must be reported to the 
dealer within 24 hours of delivery of the 
appliance.
2.
Wait at least two hours before switching the 
appliance on, to ensure that the refrigerant 
circuit is fully efficient. 
3.
Installation of the appliance and electrical 
connections must be carried out by a qualified 
electrician, in accordance with the 
manufacturers instructions and local safety 
regulations. 
4.
Clean the inside of the appliance before use.
1. Packaging 
The packaging material is 100% recyclable and 
carries the recycling symbol . Follow local 
regulations for scrapping.
Keep packing materials (plastic bags, 
polystyrene parts, etc.) out of the reach of 
children, as they are a potential source of 
danger.
2. Scrapping/Disposal
The appliance is manufactured using recyclable 
material.
This appliance is marked according to the 
European directive 2002/96/EC on Waste 
Electrical and Electronic Equipment (WEEE). 
By ensuring that this appliance is scrapped 
suitably, you can help prevent potentially 
damaging consequences for the environment 
and health.
The symbol   on the appliance, or on the 
accompanying documents, indicates that this 
appliance should not be treated as domestic 
waste but must be taken to a special collection 
centre for the recycling of electrical and 
electronic equipment.
When scrapping the appliance, make it unusable 
by cutting off the power cable and removing the 
doors and shelves so that children cannot easily 
climb inside and become trapped. Scrap the 
appliance in compliance with local regulations on 
waste disposal, taking it to a special collection 
centre; do not leave the appliance unattended 
even for a few days, since it is a potential source 
of danger for children. For further information 
on the treatment, recovery and recycling of this 
product, contact your competent local office, 
the household waste collection service or the 
shop where you purchased the appliance.Information:
This appliance does not contain CFCs. 
The refrigerant circuit contains R134a (HFCs) or 
R600a (HCs), see the rating plate inside the 
appliance.
Appliances with isobutane (R600a): Isobutane is 
a natural gas of low environmental impact. 
Caution is required, however, since isobutane is 
flammable. Therefore, ensure that refrigerant 
circuit pipelines are not damaged.
Declaration of conformity
This product has been designed for preserving 
food and is manufactured in compliance with 
Regulation (CE) No. 1935/2004.
This product has been designed, manufactured 
and marketed in compliance with:

the safety objectives prescribed in the Low 
Voltage Directive 2006/95/CE (which 
replaced Directive 73/23/CEE as amended); 

the protection requirements of the “EMC” 
89/336/CEE directive, amended by Directive 
93/68/CEE
Electrical safety of the appliance can only be 
guaranteed if it is correctly connected to an 
approved earthing system.
63602029GB.fm  Page 15  Wednesday, October 24, 2007  5:17 PM
 
						

							16
PRECAUTIONS AND GENERAL 
RECOMMENDATIONS

The appliance must be handled and installed 
by two or more persons. 

Be careful not to damage the floors when you 
move the appliance (e.g. parquet flooring). 

During installation, make sure the appliance 
does not damage the power cable. 

Check the appliance is not positioned near a 
heat source. 

To guarantee adequate ventilation, leave a 
space on both sides and above the appliance 
and follow the installation instructions. 

Keep the appliance vent outlets free. 

Do not damage the appliance refrigerant 
circuit pipes. 

Install and level the appliance on a floor strong 
enough to take its weight and in a place 
suitable for its size and use. 

Install the appliance in a dry and well 
ventilated area. The appliance is intended for 
operation in environments where ambient 
temperatures fall within the following ranges, 
depending on the climatic class indicated on 
the data plate. The appliance may not work 
properly if it is left for a long time at a 
temperature outside the specified range. 

Ensure that the voltage indicated on the 
appliance data plate corresponds to the 
domestic supply voltage. 

Do not use single/multiple adapters or 
extension cables. 

For the water connection, use the pipe 
supplied with the new appliance; do not reuse 
the one from the previous appliance. 

Power cable modification or replacement 
must only be carried out by qualified 
personnel. 

Electrical disconnection must be possible 
either by unplugging the appliance or by 
means of a double-pole switch located upline 
from the socket.SAFETY

Do not store or use petrol, flammable liquids 
or gas in the vicinity of this or other electrical 
appliances. The fumes can create a fire hazard 
or explosion. 

Do not use mechanical, electric or chemical 
means other than those recommended by the 
Manufacturer to speed up the defrost 
process. 

Do not use or place electrical appliances 
inside the product if they are not of the type 
expressly authorised by the Manufacturer. 

The appliance is not intended for use by 
persons (children included) with restricted 
physical, sensory or mental abilities or 
without experience and knowledge of the 
appliance, unless they are under the 
supervision or instruction of a person 
responsible for their safety. Do not allow 
children to play or hide inside the appliance - 
risk of becoming trapped and suffocating. 

Do not swallow the contents (non-toxic) of the 
ice packs (in some models). 

Do not eat ice cubes or ice lollies immediately 
after taking them out of the freezer since they 
may cause cold burns.
USE

Before carrying out any maintenance or 
cleaning, always unplug the appliance or 
disconnect the power supply. 

All appliances equipped with ice-makers and 
water dispensers must be connected to a 
water supply that only delivers potable water 
(with mains water pressure of between 0.17 
and 0.81 MPa (1.7 and 8.1 bar)). Ice makers 
and/or water dispensers not directly 
connected to the water mains must be filled 
using potable water only. 

Use the refrigerator compartment to store 
fresh food only and the freezer compartment 
to store frozen food, to freeze fresh food, and 
to make ice cubes only. 

Do not store glass containers with liquids in 
the freezer since they may burst.
The Manufacturer declines any liability if 
the above advice and precautions are not 
respected
Climatic Class Amb. temp. 
(°C)Amb. temp. 
(°F)
SN From 10 to 32 From 50 to 90
N From 16 to 32 From 61 to 90
ST From 16 to 38 From 61 to 100
T From 16 to 43 From 61 to 110
63602029GB.fm  Page 16  Wednesday, October 24, 2007  5:17 PM
 
						

							17
HOW TO OPERATE THE REFRIGERATOR 
COMPARTMENT
This appliance is a refrigerator with a   star freezer 
compartment.
Defrosting of the refrigerator compartment is completely 
automatic.
Switching on the refrigerator for the first time
Insert the plug into the mains socket.
The thermostat is used to adjust the temperature of both 
compartments: refrigerator and freezer.
How to adjust the temperature of the compartments:
1.
For correct operation and optimum storage of food, follow 
instructions given in the enclosed product sheet for 
thermostat adjustment.
2.
To adjust the temperature in the refrigerator compartment, 
set the thermostat control knob to:
 lowest/MIN 
numbers for the LEAST COLD
 internal 
temperatures;
highest/MAX 
numbers for the COLDEST 
internal 
temperatures.
Thermostat set to 0: no operation, no light.
Note:
The ambient air temperature, frequency of door opening and the 
position of the appliance can affect internal temperatures. These 
factors must be taken into account when setting the thermostat.
How to use the refrigerator compartment
Position the food as illustrated in the figure.
A. Cooked food
B. Fish, meat 
C. Fruit and vegetables
D. Bottles
E. Eggs
F. Butter, cheese and dairy products
Note:

The space between the shelves and the rear wall of the 
refrigerator compartment must be unobstructed to allow 
circulation of air.

Do not place food in direct contact with the rear wall of the 
refrigerator compartment.

Do not place hot food in the refrigerator or freezer.

Store liquids in closed containers.

Storing vegetables with a high water content can result in 
condensation in the crisper drawer: this will not affect the 
correct operation of the appliance.
63602029GB.fm  Page 17  Wednesday, October 24, 2007  5:17 PM
 
						

							18
HOW TO OPERATE THE FREEZER 
COMPARTMENT
The freezer is a 
 star compartment.
This compartment can be used to store frozen foods for the 
period of time indicated on packaging. The freezer can also 
be used to freeze fresh food by positioning it on the rack; 
place frozen food in the lower part of the compartment so 
that there is no contact with fresh food that has yet to be 
frozen.
The quantity of fresh food that can be frozen in 24 hours is 
shown on the rating plate.
Important:
Before freezing, wrap and seal fresh food in:

aluminium foil, cling film, air and water-tight plastic bags, 
polythene containers with lids or freezer containers suitable 
for freezing fresh food.

In the event of a power cut, the freezer compartment will 
maintain a sufficiently low temperature for food storage. 
However, it is advisable to avoid opening the compartment 
door during such periods.
Important:
The table alongside shows the recommended maximum 
storage time for frozen fresh foods.
When purchasing frozen food products:

Ensure that the packaging is not damaged (frozen food in 
damaged packaging may have deteriorated). If the package is 
swollen or has damp patches, it may not have been stored 
under optimal conditions and defrosting may have already 
begun.

When shopping, leave frozen food purchases until last and 
transport the products in a thermally insulated cool bag.

Place the items in the freezer compartment as soon as you get 
home.

If food has defrosted even partially, do not re-freeze it. 
Consume within 24 hours.

Avoid, or reduce temperature variations to the minimum. 
Respect the best-before date on the package.

Always observe the storage information on the package.
Making ice cubes

Fill the ice cube tray 3/4 with water and place it at the bottom 
of the freezer compartment.
If the tray sticks to the bottom of the compartment, do not use 
pointed or sharp instruments to detach it.
MONTHS FOOD
63602029GB.fm  Page 18  Wednesday, October 24, 2007  5:17 PM
 
						

							19
HOW TO DEFROST AND CLEAN THE 
FREEZER
HOW TO CLEAN THE REFRIGERATOR 
COMPARTMENT
Defrost the freezer compartment once or twice a year, 
or when the ice on the walls reaches a thickness of 
about 3 mm. If possible, defrost the freezer when it is 
nearly empty.
1.
Remove the food from the freezer, wrap in newspaper 
and group together in a cool place or in a portable cooler.
2. Disconnect the appliance from the mains power 
supply
.
3.
Leave the door open to allow the frost to melt.
4.
Remove the defrost water from the compartment 
bottom.
5.
Clean the interior with a sponge dampened in lukewarm 
water and neutral detergent.
Do not use abrasive products.
6.
Rinse the interior and dry thoroughly.
Note: Do not use sharp or pointed metal instruments 
to scrape off ice; do not heat the freezer compartment 
artificially.
Periodically clean the inside of the refrigerator 
compartment. 
Defrosting of the refrigerator compartment is 
completely automatic.
Droplets of water on the rear wall of the refrigerator 
compartment indicate that the periodic automatic defrost 
cycle is in progress.
The defrost water is automatically routed to a drain outlet 
and into a container from which it evaporates.
Before carrying out any cleaning operations, disconnect the 
appliance from the power supply.

Use a sponge dampened in lukewarm water and/or 
neutral detergent.

Rinse and dry with a soft cloth.
Do not use abrasive substances.
63602029GB.fm  Page 19  Wednesday, October 24, 2007  5:17 PM
 
						

							20
CLEANING AND MAINTENANCE
TROUBLESHOOTING GUIDE
1. The appliance is not working.

Is there a power failure?

Is the plug properly inserted in the socket?

Is the double-pole switch on?

Has the fuse blown?

Is the power cord damaged?

Is the thermostat set to 0 (Stop)?
2. Temperature inside the compartments is 
not low enough.

Is the door shut properly?

Is the appliance installed near a heat source?

Is the thermostat setting correct?

Are the air circulation grilles blocked?
3. Temperature inside the refrigerator 
compartment is too low.

Is the thermostat setting correct?
4. Water collects at the bottom of the 
refrigerator compartment.

Is the defrost water drain blocked?5. The inside light is not working.
Perform the checks for problem 1, and then:

Disconnect the appliance from the power 
supply.
To inspect the bulb, refer to the instructions 
and illustration on the attached table.

Check the bulb and replace it, if necessary, with 
a new one. Replace using maximum 15W bulb.
6. Excessive frost build-up in the freezer 
compartment

Is the door shut properly?

Is food obstructing proper door closure?
Attention:
 The front edge of the appliance may be 
hot. This prevents the formation of 
condensation and is not a defect.
 Gurgling and hissing noises due to 
expansion in the refrigerant circuit are 
normal.
For built-in appliances

Periodically clean air vents with a vacuum cleaner or a 
brush (see figure A
).

Clean the outside using a soft cloth.
Vacation
1.
Empty the refrigerator and freezer compartments.
2.
Disconnect the appliance from the power supply.
3.
Defrost the freezer compartment, and clean and dry both 
compartments.
4.
Leave the doors open to prevent formation of unpleasant 
odours.
Fig. A
63602029GB.fm  Page 20  Wednesday, October 24, 2007  5:17 PM
 
						

							21
AFTER-SALES SERVICE
Before contacting the After-Sales Service:
1.
See if you can solve the problem yourself (see 
“Troubleshooting guide”).
2.
Switch the appliance on again to see if the 
problem has been solved.
If it has not, switch off the appliance again and 
repeat the operation after one hour.
3.
If the problem persists after this course of 
action, contact After-Sales Service.
Specify:

the nature of the problem,

the appliance model,
the Service number (the number after the word 
SERVICE on the rating plate inside the 
appliance),

your full address,

Your telephone number and area code.
Note: The direction of door opening can be 
changed. If this operation is performed by 
After-sales Service it is not covered by the 
INSTALLATION

Install the appliance away from heat sources.

Install the appliance in a dry, well-ventilated 
place.

Do not obstruct the top and bottom vent 
zones.

Clean the inside (see chapter “How to clean the 
refrigerator compartment”).
Electrical connection
 Electrical connections must be made in 
accordance with local regulations.

Voltage and power consumption are indicated 
on the rating plate (at the side of the crispers).
Freestanding appliances (not built-in)

To optimize appliance efficiency, leave a 5 cm 
gap above the appliance and make sure that 
adjacent kitchen units are sufficiently distanced 
to allow air circulation.

Ensure that the appliance is level, using the 
front adjustment feet if necessary. Regulations require that the appliance be 
earthed. The manufacturer declines all 
liability for injury to persons or animals 
and for damage to property resulting from 
failure to observe the above procedures 
and reminders.

If the plug and socket are not of the same type, 
have the socket replaced by a qualified 
electrician.

Do not use extension leads or adapters.
Disconnecting the appliance

It must be possible to disconnect the appliance 
by unplugging it or by means of a two-pole 
switch fitted upline of the socket.
63602029GB.fm  Page 21  Wednesday, October 24, 2007  5:17 PM
 
						

							22
DOOR REVERSIBILITY
The doors of your Fridge Freezer can be reversed.

Ensure the Fridge Freezer is unpugged and empty.

We recommend you have someone to assist you.
Tools required

Phillips style screwdriver

Flat bladed screwdriver

8 mm and 10 mm Socket or spanner.
When laying the Frdge Freezer on its back in order to gain 
access to the base, you should never tip it back by more than 
45º and must rest it on soft foam packaging or similar material 
to avoid damaging the cooling pipes at the rear of the Frdge 
Freezer.
Remove the two screws at the rear of the Fridge Freezer. 
Lift the top off the Fridge Freezer.
Use the 8 mm socket or spanner to remove the 3 hinge bolts. 
Remove the 3 bolts from the opposite side.
Remove bracket and plastic surround. Remove and replace 
the pin in the bracket. Replace on opposite side of the Fridge 
Freezer cabinet.
Lift the top door off middle hinge bracket and pull away from 
the body of the Fridge Freezer. Remove retaining screw from 
the top of the cabinet and replace on the other side.
Remove the middle hinge using an 8 mm socket/spanner. 
Take care not to lose the white spacer. Put hinge to one side. 
Lift door off the bottom bracket. 
Remove blanking plates from the middle of the cabinet and 
replace in opposite side. Remove the blanking plates from the 
doors and replace the hinge bushes on the other side.
63602029GB.fm  Page 22  Wednesday, October 24, 2007  5:17 PM
 
						

							23
Remove the levelling feet by unscrewing.
Remove bottom bracket using an 8 mm socket or spanner. 
Remove and replace pin using a 10 mm spanner to undo the 
nut and a flat bladed screwdriver to remove the pin. You may 
need to push the pin through from the underside to remove 
fully.
Remove screw on base and replace on other side. 
Remove blanking plates from unused side of the Fridge 
Freezer and replace in holes left by the brackets. 
Replace doors and brackets in reverse order. 
When replacing feet take care to ensure the larger foot is on 
the side without the bracket.
Check both doors are aligned horizontally and vertically, and 
that the seals are closed on all sides before finally tightening 
the bottom hinge
63602029GB.fm  Page 23  Wednesday, October 24, 2007  5:17 PM