Whirlpool AFB 910 Manual

							14
INSTRUCTIONS FOR USE
BEFORE USING THE APPLIANCE
SAFEGUARDING THE ENVIRONMENT
PRECAUTIONS AND GENERAL 
RECOMMENDATIONS
USING THE FREEZER
DEFROSTING AND CLEANING THE FREEZER
CLEANING AND MAINTENANCE
TROUBLESHOOTING GUIDE
AFTER-SALES SERVICE
INSTALLATION
ELECTRICAL CONNECTION
60202011GB.fm  Page 14  Thursday, July 12, 2007  5:31 PM
 
						

							15
BEFORE USING THE APPLIANCE
SAFEGUARDING THE ENVIRONMENT
•
Your new appliance is designed exclusively for 
domestic use.
To ensure best use of your appliance, 
carefully read the instructions which contain 
a description of the appliance and advice on 
storing and preserving food.
Keep this handbook for future reference.1.
After unpacking the appliance, make sure it is 
not damaged and that the door closes 
properly. Any damage must be reported to the 
dealer within 24 hours of delivery of the 
appliance.
2.
Wait at least two hours before switching the 
appliance on, in order to ensure that the 
refrigerant circuit is fully efficient.
3.
Make sure installation and the electrical 
connection are carried out by a qualified 
technician according to the manufacturers 
instructions and in compliance with the local 
safety regulations
4.
Clean the inside of the appliance before using it.
1. Packing 
The packing material is 100% recyclable and 
bears the recycling symbol. Comply with the 
local regulations for disposal. Keep the packing 
materials (plastic bags, polystyrene parts, etc.) 
out of the reach of children, as they are a 
potential source of danger.
2. Scrapping/Disposal
The appliance is manufactured using recyclable 
material.
This appliance is marked in compliance with 
European Directive 2002/96/EC on Waste 
Electrical and Electronic Equipment (WEEE).
By ensuring the correct scrapping of this 
appliance, you can help prevent potentially 
negative consequences for the environment and 
the health of persons.
The symbol   on the appliance, or on the 
accompanying documents, indicates that this 
appliance should not be treated as domestic 
waste but must be taken to a suitable collection 
centre for the recycling of electrical and 
electronic equipment.
When scrapping the appliance, make it unusable 
by cutting off the power cable and removing the 
doors and shelves so that children cannot easily 
climb inside.
Scrap the appliance in compliance with local 
regulations on waste disposal, taking it to a 
special collection centre; do not leave the 
appliance unattended even for a few days, since 
it is a potential source of danger for children. For 
further information on the treatment, recovery 
and recycling of this product, contact your 
competent local office, the household waste 
collection service or the shop where you 
purchased the appliance.Information:
This appliance does not contain CFCs. 
The refrigerant circuit contains R134a (HFCs) or 
R600a (HCs), see the rating plate inside the 
appliance.
Appliances with isobutane (R600a): Isobutane is 
a natural gas without environmental impact but 
is flammable. Therefore, make sure the 
refrigerant circuit pipes are not damaged.
This product contains Fluorinated Greenhouse 
Gases covered by the Kyoto Protocol, the 
refrigerant gas being in a hermetically sealed 
system. 
Refrigerant gas: R134a has a Global Warming 
Potential (GWP) 1300.
Declaration of conformity

This appliance is intended for storing food and 
is manufactured in conformity with European 
regulation (EC) No. 1935/2004.

This product has been designed, 
manufactured and marketed in compliance 
with:
- the safety objectives prescribed in the Low 
Voltage Directive 2006/95/CE (which replaced 
Directive 73/23/CEE as amended);
- the protection requirements of the “EMC” 
89/336/CEE directive, amended by Directive
93/68/CEE.
Electrical safety of the appliance is guaranteed 
only if it is connected to an efficient and 
approved earthing system
.
60202011GB.fm  Page 15  Thursday, July 12, 2007  5:31 PM
 
						

							16
PRECAUTIONS AND GENERAL 
RECOMMENDATIONS

During installation, make sure the appliance 
does not damage the power cable.

Make sure the appliance is not near a heat 
source.

To guarantee adequate ventilation, leave a 
space on both sides and above the appliance 
and follow the installation instructions.

Keep the appliance ventilation openings free.

Power cable modification or replacement 
must only be carried out by qualified 
personnel.

It must be possible to disconnect the 
appliance from the power supply by 
unplugging it or by means of a mains double-
pole switch installed upstream of the socket.

Make sure the voltage specified on the rating 
plate corresponds to that of your home

Install and level the appliance on a floor strong 
enough to take its weight and in a place 
suitable for its size and use.

The appliance must be handled and installed 
by two or more persons. 

Be careful not to damage the floors (e.g. 
parquet) when moving the appliance.

Do not use single/multi-adapters or extension 
cords.

Install the appliance in a dry and well-
ventilated place. The appliance is arranged for 
operation in places where the temperature 
comes within the following ranges, according 
to the climatic class given on the rating plate. 
The appliance may not work properly if it is 
left for a long period at a temperature outside 
the specified range.
Do not store or use petrol, gas or flammable 
liquids in the vicinity of this or other electrical 
appliances. The fumes can cause fires or 
explosions.

Do not use mechanical, electric or chemical 
means other than those recommended by the 
Manufacturer to speed up the defrost 
process.

Do not damage the appliance refrigerant 
circuit pipes.

Do not use or place electrical devices inside 
the appliance compartments, if they are not of 
the type expressly authorised by the 
Manufacturer.

This appliance is not intended for use by 
persons (including children) with reduced 
physical, sensory or mental capabilities, or 
lack of experience and knowledge, unless 
they have been given supervision or 
instruction concerning use of the appliance by 
a person responsible for their safety. Children 
should be supervised to ensure that they dont 
play with the appliance.

Do not swallow the contents (non-toxic) of 
the ice packs (if provided).

Use the refrigerator compartment only for 
storing fresh food and the freezer 
compartment only for storing frozen food, 
freezing fresh food and making ice cubes.

Do not store glass containers with liquids in 
the freezer since they may burst.

Do not eat ice cubes or ice lollies immediately 
after taking them out of the freezer since they 
may cause cold burns.

Before carrying out any maintenance or 
cleaning operation, unplug the appliance or 
disconnect it from the power supply.
 The Manufacturer declines any liability if 
the above advice and precautions are not 
respected.
Climatic Class Amb. T. (°C) Amb. T. (°F)
SN From 10 to 32 From 50 to 90
N From 16 to 32 From 61 to 90
ST From 16 to 38 From 61 to 100
T From 16 to 43 From 61 to 110
60202011GB.fm  Page 16  Thursday, July 12, 2007  5:31 PM
 
						

							17
USING THE FREEZER
The freezer can be used for storing already frozen food and 
for freezing fresh food.
Switching on the freezer for the first time
The freezer temperature does not have to set with the 
thermostat because the appliance is already factory-set.

Plug in the appliance.

Only place food in the freezer 2 hours after switching on.
Temperature adjustment
Settings from MIN to MAX: increase the cooling temperature.

Thermostat setting:
MIN - storing food for short periods;
NORMAL - storing food for longer periods;
MAX + SUPER - storing food for long periods and freezing food.
Note:
The room temperature, how often the door is opened and the 
position of the appliance can affect the temperature inside the 
freezer.
Take these factors into account when setting the thermostat.
Freezing
Place the maximum amount indicated on the rating plate, 
in the middle compartment, taking care not to place it in 
contact with already frozen food.
For optimum appliance performance, turn the thermostat knob to 
Super, introduce the food to be frozen, and after 24 hours turn the 
knob back to Normal.
About 24 hours on “SUPER” after introducing the food is generally 
sufficient; after this period, deactivate the “SUPER” function (if 
present).
Important:
When freezing small amounts of food, the food can be placed in 
any compartment except the bottom drawer. 
Also, in order to save energy, the fast freeze function (if present) 
does not have to be activated.
NORMAL
MAX
SUPERMIN
Control unit
Storage
baskets
Adjustment devices
Control unit
60202011GB.fm  Page 17  Thursday, July 12, 2007  5:31 PM
 
						

							18
Advice for freezing and storing fresh food.

Before freezing, wrap and seal fresh food in: 
aluminium foil, transparent film, waterproof plastic bags, 
polyethylene containers with lids or freezer containers suitable 
for the food being frozen.

Food must be fresh and of prime quality.

If possible, fresh vegetables and fruit should be frozen 
immediately after being picked, to preserve the nutritional 
substances, structure, consistency, colour and flavour.
Note:

Always leave hot food to cool before placing in the freezer.

Consume fully or partially thawed foods immediately. 
Do not refreeze unless the thawed food is used to prepare a 
ready meal. Once cooked, the thawed food can be refrozen.
Important:
The table opposite gives the recommended storage times 
for frozen fresh foods.
Classification of frozen foods
Put the frozen products in the freezer and classify them.
It is advisable to indicate the storage date on the packs, to ensure 
their use before the expiry dates.
Advice for storing deep-frozen food
When purchasing deep-frozen food products:

Make sure the packaging is not damaged, otherwise the food 
can deteriorate. If the package is swollen or has damp patches, 
it has not been stored in optimum conditions and may have 
started to thaw.

Purchase frozen food last and use thermal bags to carry it.

Place frozen foods in the freezer as soon as you get home.

Do not refreeze partially thawed food products; consume them 
within 24 hours.

Avoid or reduce temperature variations to a minimum. 
Respect the expiry date on the pack.

Always follow the instructions given on the pack for storing 
frozen foods.MONTHS FOOD
60202011GB.fm  Page 18  Thursday, July 12, 2007  5:31 PM
 
						

							19
Removing the drawers

Pull out the drawers as far as they go, then lift slightly and 
remove.
Note:
The drawers can be removed in order to obtain more space.
Make sure that the load does not exceed the limit (if present) 
indicated on the side walls of the appliance.
Making ice cubes

Fill the ice cube tray 2/3 full and place it in the special freezer 
compartment.

Do not use sharp or pointed instruments to detach the tray if it 
is stuck to the bottom of the freezer.

Bend the ice tray slightly to remove the cubes.
Note:
The freezer door will not re-open easily immediately after closing.
Wait a few minutes before opening again in order to allow for 
compensation of the vacuum created.
Fig. 1
60202011GB.fm  Page 19  Thursday, July 12, 2007  5:31 PM
 
						

							20
DEFROSTING AND CLEANING THE FREEZER
CLEANING AND MAINTENANCE
Before any cleaning or maintenance operation, always 
unplug the appliance or disconnect it from the power 
supply.
Defrost the freezer once or twice a year, or when the 
frost on the refrigeration grills is excessive.
It is perfectly normal for frost to form on the grills. The 
amount of frost and the speed at which it accumulates 
depend on room conditions how often the door is 
opened, and tends to accumulate more on the upper 
grills.
It is advisable to defrost the freezer when it is nearly 
empty.

Open the door and remove all food products, wrapping 
them close together in newspaper and place in a very cool 
place or in a portable cooler.

Leave the freezer door open to allow the frost to melt.

Clean the inside of the freezer with a sponge soaked in 
lukewarm water and/or neutral detergent. Do not use 
abrasive substances.

Rinse and dry thoroughly.

Put the food back into the freezer.

Close the freezer door.

Plug in the appliance.

Switch the freezer on.
Periodically clean the condenser at the back of the appliance 
with a vacuum cleaner or brush.
For long vacations

Empty the freezer.

Disconnect the freezer from the power supply.

Defrost and clean the inside.
 Leave the door open to prevent the formation of 
unpleasant odours and to eliminate the moisture 
inside.
60202011GB.fm  Page 20  Thursday, July 12, 2007  5:31 PM
 
						

							21
TROUBLESHOOTING GUIDE
1. The appliance does not work.

Is there a power failure?

Is the main switch turned on?

Are the household electrical system 
protection devices efficient?

Is the thermostat correctly set?

Was the appliance switched on correctly?
2. Excessive frost build-up.

Is the defrost water drain correctly 
positioned?

Was the door properly shut?Notes:
 If the front edge of the appliance is hot, this 
is not a defect but prevents the formation of 
condensate.
 Gurgling and hissing noises due to 
expansion in the refrigerant circuit are 
normal.
AFTER-SALES SERVICE
Before contacting the After-Sales Service:
1.
See if you can solve the problems on your own 
(see “Troubleshooting guide”).
2.
Switch the appliance on again to see if the 
problem has been eliminated. If it has not, 
disconnect the appliance again and repeat the 
operation after one hour.
3.
If the problem persists, contact the After-Sales 
Service.Specify:

the type of fault,

the model,

the Service number (the number after the 
word SERVICE on the rating plate inside the 
appliance),

your full address,

your telephone number and area code.
60202011GB.fm  Page 21  Thursday, July 12, 2007  5:31 PM
 
						

							22
INSTALLATION

Install the freezer away from heat sources. Installation in a 
hot place, direct exposure to sunlight or placing it near a 
heat source (radiators, cookers) will increase energy 
consumption and should therefore be avoided.

If this is not possible, the following minimum distances must 
be respected:

30 cm from coal or oil stoves;

3 cm from electric and/or gas cookers.

Install in a dry and well-ventilated place.

Clean the inside (see “Defrosting and cleaning the 
freezer”).

Fit the accessories supplied.

Fit the spacers (Fig. 1
, 2
, or 3
, depending on the model)
Electrical connection
 Electrical connections must be made in compliance 
with local regulations.

Data regarding voltage and electrical absorption are 
specified on the rating plate inside the appliance.

Earthing of the appliance is compulsory by law. 
The Manufacturer declines any liability for injury to 
persons and animals or damage due to non-
compliance with the above regulations.

If the plug and socket are not of the same type, have the 
socket replaced by a qualified technician.

Do not use extension leads or multi-adapters.
Electrical disconnection
It must be possible to electrically disconnect the appliance by 
unplugging it or by means of a double-pole switch installed 
upstream of the socket.
Door reversibility
If required, door opening can be reversed from right to left 
(depending on how it is supplied).
Caution! 
When reversing the door opening, the appliance 
must not be connected to the power supply. The appliance 
must be previously unplugged.
Tilt the appliance backwards a little and prop it in a secure 
position.
Undo the door hinge screws and remove the hinge pin 
bracket.
Open the door slightly and lower it.
Undo the top pin and screw it in place on the opposite side.
Insert the door on the top hinge and close it.
Tighten the hinge pin bracket in place on the opposite side 
using the screws.
60202011GB.fm  Page 22  Thursday, July 12, 2007  5:31 PM
 
						

							23
Installation requirements
To ensure correct appliance operation, it must not be exposed to 
temperatures below 16 °C or above 32 °C.
It is advisable to avoid the following places: kitchens without 
ventilation, outside rooms, greenhouses, garages. In order to 
operate correctly, the appliance must be installed:
in a dry place.
Away from direct sunlight.
Away from extreme temperatures (away from cookers or other 
heat sources).
When full, the appliance will be heavy, and therefore it must be 
placed on a strong and solid floor.
Ventilation requirements
Carefully push the freezer in place, until reaching the appropriate 
distance from the wall.
When in place, a space of 50 mm above the appliance must be 
maintained.
If the space is not available above the appliance, leave a space of 
25mm on both sides.
Make sure the appliance does not squash the power cable.
The parts that can become hot must not be exposed. When possible, 
the back part of the appliance must be close to the wall, leaving the 
required space for ventilation.
Levelling
The appliance must be level; to eliminate rocking:
make sure the appliance is vertical and that both adjustment 
devices are in close contact with the floor, so that the 
compartment is level. 
Adjust the level by unscrewing the appropriate adjustment device, 
located at the front (use fingers or a screwdriver).
The appliance is heavy. Pay attention when moving it.
* For specific details please refer to the rating plate located on the 
back of the freezer. The specifications are subject to change 
without notice.
Note:
If reversing of door opening is carried out by the After-sales 
Service the work is not covered by the warranty.
WALL
60202011GB.fm  Page 23  Thursday, July 12, 2007  5:31 PM