Home > Whirlpool > Dishwasher > Whirlpool Adg 6556 Wh Manual

Whirlpool Adg 6556 Wh Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Whirlpool Adg 6556 Wh Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 415 Whirlpool manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							10
    GBCONTENTS
    BEFORE USING THE DISHWASHERPAGE11
    PROTECTING THE ENVIRONMENTPAGE11
    PRECAUTIONS AND GENERAL RECOMMENDATIONSPAGE11
    CONNECTIONSPAGE12
    ELECTRICAL CONNECTIONPAGE13
    HOW TO FILL THE SALT CONTAINERPAGE14
    HOW TO FILL THE RINSE AID DISPENSERPAGE15
    HOW TO FILL THE DETERGENT DISPENSERPAGE16
    CARE AND MAINTENANCEPAGE17
    To make the most of your new dishwasher, please read these user
    instructions and the quick reference guide carefully.
     
    						
    							11 1.   Removing the packaging and check
    After unpacking, make sure that the 
    dishwasher is undamaged and that the door 
    closes correctly. If in doubt, contact a qualified 
    technician or your local retailer.
    •      Keep the packaging materials (plastic bags, 
    polystyrene parts, etc.) out of reach of 
    children, as they are potentially dangerous.2. Water and electrical connections
    All water and electrical connections must be 
    carried out by a qualified technician in 
    compliance with the manufacturers 
    instructions (refer to the enclosed installation 
    booklet) and current local safety regulations.
    The appliance must only be used in the 
    household for the prescribed uses.
    1. Packing 
    The packing box may be fully recycled as 
    confirmed by the recycling symbol  .
    2. Energy and water saving tips
    Do not rinse crockery under running water.
    Always fully load the dishwasher before 
    switching on or set the wash programme to 
    half load (if available) if 
    one rack only is 
    loaded.If ecological energy sources are available, 
    such as solar panel heating, heat pumps or 
    centralised heating systems, the appliance 
    may be connected to the hot water mains up 
    to a maximum temperature of 60° C. Make 
    sure the water inlet hose is of the correct 
    type. Refer to the chapter “Connections” in 
    these user instructions.
    3. Disposing of packaging and old machine
    The appliance is built from reusable 
    materials. If you decide to scrap the 
    dishwasher, it must be disposed of in 
    compliance with local waste disposal laws.
    Before scrapping, cut off the power cable 
    so that the appliance cannot be 
    connected to the mains.
    1. Child safety:
    Children must not be allowed to play with 
    the dishwasher.
    Store the detergent, rinse aid and salt in a 
    dry place out of the reach of children.
    2. General recommendations:
    The open dishwasher door can only support 
    the weight of the loaded rack when pulled 
    out. Do not rest objects on the open door or 
    sit or stand on it: 
    the appliance may topple 
    over!
    Do not use solvents inside the dishwasher: 
    risk of explosion!
    Only use detergents, rinse aids and 
    regeneration salts specially recommended 
    for use in domestic dishwashers.
    Before cleaning or carrying out 
    maintenance, switch off the appliance and 
    turn off the water tap.
    If a fault occurs, switch off the appliance and 
    turn off the water tap.If necessary, the power cable may be 
    replaced with one the same obtained from 
    our After-Sales Service. The power cable 
    must only be replaced by a qualified 
    technician.
    On completion of the programme switch off 
    the dishwasher and turn off the water tap.
    3. For appliances with water stop system: 
    The water inlet hose and plastic casing 
    contain electrical components. Do not 
    therefore cut the hose or immerse the plastic 
    casing in water. If the hose is damaged 
    switch off the appliance immediately.
    EC Declaration of conformity
    This appliance has been designed, constructed 
    and distributed in compliance with the safety 
    requirements of EC Directives:
    73/23/EC
    89/336/EC
    93/68/EC
    Load capacity: 12 place settings
    .
    BEFORE USING THE DISHWASHER
    PROTECTING THE ENVIRONMENT
    PRECAUTIONS AND GENERAL RECOMMENDATIONS
     
    						
    							12Do not use the dishwasher if it has been 
    damaged in transit. Consult your local 
    retailer or our After-Sales Service.
    (Refer to the separate installation instructions 
    booklet)
    Water inlet and drain: 
    
    Observe any special regulations issued by 
    your local Water Board.
    
    Make sure the inlet and drain hoses are kink-
    free and are not crushed.
    
    If the hose length is not sufficient, please 
    contact your local dealer or our After-Sales 
    Service.
    
    The inlet hose must be securely screwed on 
    to the water tap to prevent leaks.
    
    The inlet water temperature varies according to 
    the model installed: inlet hose marked “25°C 
    Max”: maximum temperature 25°C. 
    All other models: maximum temperature 60°C.
    
    When installing the appliance, make sure the 
    drain water discharges correctly (if necessary, 
    remove the plug from the sink spigot).
    
    Fix the drain hose to the spigot with a clamp 
    to prevent it from coming off during operation.
    
    For appliances with water-stop system only: 
    if the water connections are made correctly, 
    the water-stop system safeguards your home 
    against damage caused by flooding.
    Electrical connection:
    
    Closely adhere to local Electricity Board 
    regulations.
    
    Voltage information is shown on the rating 
    plate mounted inside the door on the right 
    hand side.
    
    The appliance must be earthed as prescribed 
    by law.
    
    Do not use extension leads or multiple 
    adapters.
    
    Before carrying out maintenance, disconnect 
    the mains plug.
    
    The power cable must only be replaced by a 
    qualified technician.
    For Austria: 
    if the apparatus is series 
    connected to a fault current switch, this must 
    be sensitive to the pulsating current.
    CONNECTIONS
     
    						
    							13 For Great Britain Only
    Warning - this appliance must be 
    earthed
    Fuse replacement
    If the mains lead of this appliance is fitted with a 
    BS 1363A 13amp fused plug, to change a fuse in 
    this type of plug use an A.S.T.A. approved fuse 
    to BS 1362 type and proceed as follows:
    1.Remove the fuse cover (A) and fuse (B).
    2.Fit replacement 13A fuse into fuse cover.
    3.Refit both into plug.
    Important:
    The fuse cover must be refitted when changing a 
    fuse and if the fuse cover is lost the plug must not 
    be used until a correct replacement is fitted.
    Correct replacement are identified by the colour 
    insert or the colour embossed in words on the 
    base of the plug.
    Replacement fuse covers are available from 
    your local electrical store.
    Connection to a rewirable plug
    If the fitted plug is not suitable for your socket 
    outlet, then it should be cut off and disposed of in 
    order to avoid a possible shock hazard should it 
    be inserted into a 13A socket elsewhere.
    A suitable alternative plug should then be fitted 
    to the cable.The wires in the mains lead are coloured in 
    accordance with the following code:
    BLUE - “NEUTRAL” (“N”)
    BROWN- “LIVE” (“L”)
    GREEN AND YELLOW - “EARTH” (“E”)
    1.The GREEN AND YELLOW wire must be 
    connected to the terminal in the plug which is 
    marked with the letter “E” or by the Earth 
    symbol   or coloured green or green and 
    yellow.
    2.The BLUE wire must be connected to the 
    terminal which is marked with the letter “N” or 
    coloured black.
    3.The BROWN wire must be connected to the 
    terminal which is marked with the letter “L” or 
    coloured red.
    For the Republic of Ireland only
    The information given in respect of Great Britain 
    will frequently apply, but a third type of plug and 
    socket is also used, the 2-pin, side earth type. In 
    this case, the wire which is coloured GREEN 
    AND YELLOW must be connected to the EARTH 
    contact, and the two wires to the two pins, 
    irrespective of colour. The supply to the socket 
    must be fitted with a 16 amp fuse.
    ELECTRICAL CONNECTION
     
    						
    							14 From a water hardness category of 1-2 
    (average), before using the dishwasher, fill the 
    salt container with regeneration salt (to find out 
    the hardness level of water in your area, contact 
    your local Water Board or check the last bill you 
    received).
    If the water hardness level does not correspond 
    to position 3 on the selector (setting on delivery) 
    or if the water hardness level changes:
    Turn the selector to the correct position.
    Set the water hardness by turning the selector (if 
    fitted) inside the door (top left) using a screwdriver. 
    Use the table below to set the dial to the correct 
    setting:
    If the water hardness level falls within category
    1 (soft), no salt is required.
    How to fill the salt container
    Warning: only use regeneration salts for 
    use in domestic dishwashers!
    Do not fill the salt container with unsuitable 
    substances, such as detergent, as this will 
    cause irreparable damage to the water 
    softener system.
    1.   Remove the lower rack.
    2.Unscrew the cap by turning it counter-
    clockwise.
    3.When first using the dishwasher: fill the salt 
    container to the rim with water.
    4.Fill the salt container to the rim with salt 
    (using the filler provided) (when filling for the 
    first time use min. 1.5 kg and max. 2 kg) and 
    stir with a spoon handle.
    5.Screw the cap back on by turning it 
    clockwise.
    6.Fit the lower rack.
    7.After filling the regeneration salt container, 
    immediately
     start a wash program (the 
    Prewash program alone is not sufficient), so 
    as to eliminate any residual saline solution 
    straight away.
    Check the salt level regularly.
    Salt level indicator
    The dishwasher is equipped with an electric or 
    visual salt level indicator (depending on the 
    model installed).
    Electric indicator:
    The salt level indicator lamp   on the control 
    panel lights up when the salt container is empty.
    Visual indicator:
    The float is clearly visible in the cap window 
    when the salt container is full. 
    The float lowers and is no longer visible when the 
    salt container is empty.
    HOW TO FILL THE SALT CONTAINER
    Hardness 
    categoryGerman 
    degrees
    °dHFrench 
    degrees
    °fHPosition
    of
    selector
    1 soft 0 - 5 0 - 9 0
    1 - 2 average 6 - 10 10 - 18 1
    2 average 11 - 15 19 - 27 2
    3 medium-hard 16 - 21 28 - 37 3
    4 hard 22 - 28 38 - 50 4
    4 very hard 29 - 35 51 - 63 5
    4 extremely 
    hard36 - 60 64 - 107 6
     
    						
    							15 The rinse aid facilitates drying and prevents the 
    formation of unsightly spots and streaks on 
    crockery. Before using the dishwasher for the 
    first time, fill the rinse aid dispenser.
    How to fill the rinse aid dispenser:
    Only use rinse aids recommended for use in 
    domestic dishwashers.
    1.   Press button A
     to open the cover
    (see drawing). 
    2. Fill the dispenser with rinse aid up to the 
    dashed line “max” (about 100 ml.).
    Immediately wipe away any rinse aid spilt 
    accidentally.
    This prevents the formation of excess suds 
    which may spoil washing results.
    3. Replace the cover.
    Thereafter, regularly check the rinse aid level.
    How to adjust the rinse aid dosage 
    regulator:
    Factory setting: position 4.
    If you are not satisfied with washing or drying 
    results, change the rinse aid dosage setting. 
    1.   Press button A
     to open the cover (see 
    drawing).
    2. If crockery is prone to whitish streaks, reduce 
    the dosage by turning the dial to a lower 
    setting (1-3) using a coin or the like. 
    If crockery is not perfectly dry, increase the 
    dosage by turning the dial to a higher setting 
    (5-6).
    3. Close the cover again.
    Rinse aid level indicator:
    Visual indicator:
    light
    = add rinse aid .
    dark
    = sufficient rinse aid  .
    Additional electric indicator (if provided):
    The indicator lamp   on the control panel 
    lights up when more rinse aid needs to be added.
    HOW TO FILL THE RINSE AID DISPENSER
     
    						
    							16A small compartment   and a large 
    compartment  are provided for the 
    detergent.
    The use of detergent in excess of the 
    recommended dosage may cause pollution. The 
    recommended dosage varies for different 
    brands.
    If you use detergents in pellet form, follow the 
    manufacturer’s directions for use.
    “New generation” detergents contain enzymes 
    that give better washing results when Bio 
    programmes are used. However, these 
    programmes are also suitable for all other 
    dishwasher detergents.
    How to fill the detergent dispenser:
    Only use detergents recommended for use 
    in domestic dishwashers.
    Only fill the detergent dispenser prior to 
    starting a wash programme.
    1.   Press button 
    A to open the cover.
    2. How to fill the Detergent Dispenser.
    For programmes with pre-rinse:
    Pour 2/3 of the recommended dosage into 
    the large compartment  .
    Pour the remaining 1/3 into the small 
    compartment .
    For programmes without pre-rinse:
    Pour the entire recommended dosage into 
    the large compartment. If the recommended 
    dosage on the detergent pack is over 
    45 ml (maximum capacity of the large 
    compartment), pour the remaining detergent 
    into the small compartment.
    For programmes with additional 
    “Half load” 
    function selected (if provided): Use a smaller 
    quantity of detergent.
    3. Close the cover.
    HOW TO FILL THE DETERGENT DISPENSER
    LargeSmall
    compartment
    compartment
     
    						
    							17
    Before cleaning or carrying out 
    maintenance, switch off the appliance and 
    turn off the water tap.
    Cleaning the outside of the appliance:
    To clean the outside of the appliance, use a 
    neutral detergent and a damp cloth.
    Do not use abrasive detergents.
    Cleaning the inside of the dishwasher:
    Regularly wipe the door seal and inside of 
    the door with a damp cloth to remove any 
    food residues.
    Upper spray arm:
    1.  Slacken the fixing nut (A) (by turning it 
    counter-clockwise) and detach the spray 
    arm (B) by pulling it down.
    2.Rinse the nozzles.
    3.Remount the spray arm by aligning it with the 
    rotary mounting and insert it.
    4.Tighten the fixing nut by turning it clockwise. 
    Make sure the nut is fully tightened (it 
    should click). 
    Make sure the spray arm rotates freely.
    Lower spray arm:
    1.  Press the two levers which fix the spray arm 
    inwards (C), and detach by pulling it up (D).
    2.Rinse the nozzles.
    3.Remount the spray arm by aligning it with 
    the rotor pin and insert it.
    4.Push the spray arm down firmly until it is 
    fixed in place.
    5.Make sure the two levers are correctly 
    inserted (they should click).
    Make sure the spray arm rotates freely.
    Cleaning the filters:
    1.  Fully unscrew the wide-mesh central filter by 
    turning it counter-clockwise and extract it 
    (E).
    2.Fully unscrew the fine-mesh filter and 
    extract it from the wide-mesh central filter (F) 
    (pay due attention to the holes in the bottom 
    of the filter).
    3.Remove the large filter (G).
    4.Clean all filters regularly under running 
    water, and check that no impurities are left 
    inside the dishwasher.
    5.Reassemble:
    Insert the fine-mesh filter in the wide-mesh 
    central filter (pay due attention to the holes 
    in the bottom of the filter).
    Insert the filter unit and fix it by turning it 
    clockwise. Make sure that the filters have 
    been inserted correctly.
    The filter unit must be correctly 
    assembled to ensure good wash results.
    CARE AND MAINTENANCE
     
    						
    All Whirlpool manuals Comments (0)

    Related Manuals for Whirlpool Adg 6556 Wh Manual