Vodavi Triad 1/2/3 Installation Manual

5- 18 Re mo te M ai nte nance
Sys te m Co nf igu ration
Figure 5- 2:is a conf iguration of theTriad 1/2/3Syst e ms d is pla ys what i s
printed whe n:
The i nst al le r typ esdsat th emaint>pr omp t.
Fi g u r e 5- 2: R em ot e S yst em C o nf i gu r at i o n
Where:
Colu mn 1lists the card slot.
Colu mn 2l is ts car d t ype of t hat car d sl ot .
Colu mn 3l is ts t he fir mwa re ve rsi o n o f t he c ard.
Colu mn 4lists card type and if that card is installed.
Colu mn 5lists card options.
Colu mn 6l is ts...

Remo t e Mai n tena nce 5 - 19
Figure 5-3: Station Configuration
Column
Indicates:
1 Stati on Nu mb er
2 Stati on Ty p e (key set, D SS, SLT )
Keyset - I D 0 = Key stati on
DXX 1 = DSS Map 1
DXX 2 = DSS Map 2
DXX 3 = DSS Map 3
DXX 4 = DSS Map 4
DXX 5 = DSS Map 5
SLT - ID 6 = SLT
SLT w/ Lamp - I D 7 = SLT w/ Message Wait ing
3 Statu s:
†OOSstatus can indi cate t he enti re card i s out of ser vic e; a spec ific stati on is
not install ed; o r i nstal led but not operati onal .
†INSstatus can indicate a...

5- 20 Re mo te M ai nte nance
CO Li ne Co nf iguratio n
Figure 5- 4illustrates a representation of what is printed out for slot two
when a LCOB is installed in that slot and:
The i nst al le r typ esds2at th emaint>pr omp t.
Figure 5-4: CO Line Configuration
Column
In di ca tes:
1COLineNumber
2 Statu s:
†OOSstat us can indicate the entire car d isoutofservic e.
†INSstatus can indicate a board station isin-ser vice an d op erati ng co rrec tly .
I nc omi ng = In co mi ng CO l in e ca ll s a re a llo wed...

Remo t e Mai n tena nce 5 - 21
Event Tr ac e Buf fer
TheEventTraceBufferisusedtostoreanddumpeventtraces(upto30)
tha t occu r just prior to aTr ia d 1 /2 /3System soft or hard restart. These can
then be reviewed by authorized personnel to aid in system
troubles hooting. Th e b asic format f or the comma nds are:
Tabl e 5 -2 0: Event Tra ce Buf fer Co mm ands
Co m ma n d F u n ct i on
t  Displays the current status of the Event tr ace buffer.
t 0 Tur ns th e Trace b uffer OFF.
t 1  Tur ns th e Trace b...

5-22 R emo te Syst em Mo nit or
DT M F R ece iver Tra ce
The CONFIG utility to allow technicians to take specific DTMF receivers
in/out of serv ice. T his is us eful fo r troublesh ooting D TMF receiver
pr oble ms to is ola te a spe c if ic D TM F re c ei ve r t hat m ay b e f aul ty.
Conne ct a te rminal to the I/O port 1 on the MPB. At the E NTE R
PAS SWO RD prom pt ty pe CO NFI G a nd pr e ss ENT ER.
The ba si c for mat for t he comman ds i s:
dr- To display the status of all DTMF receivers in the
sys...

Remote System Monitor 5-23
Mo ni t or Pa ss w or d
The Remote Monitor feature, like Remote Maintenance, is entered via a
si x-char act er a lph anume ri c st r ing. T he p ass word pr ompt i s g ive n b y
pr ess ing t he <
r> key at the device connected to the SIU or SIU2 Module.
Af te r the p romp t is pr int ed out , t he pas swor d s hould be e nte re d
fol lowe d b y t he <
r> key. Proper entry of the pa ssword results in the
mon>prompt. The Remote Maintenance password is: {ETRACE}
He lp M en u ( ?...

5-24 R emo te Syst em Mo nit or
Dump Memory Data
Three options allow the memory structure to bedumpe dfor viewing.
The three options are entered as follows:
c[c]–Dump CO Li ne memor y structur e
s[s]–Dump Station memory structure
d[a][a]–Dump a memory address structure
The da ta obt ain ed f rom the se comman ds i s i n he xade cim al for mat and is
use d pr i mar il y f or m anufa ct ur er - le vel s uppor t .
Event Tr ac e Mo de
The t comma nd e nable s a nd disa ble s theTriad 1/2/3Syst e ms’Tr ace...

Remote System Monitor 5-25
1. To enable an Event Trace, typet(space bar).
2. Then type of trace desired [d], wheredi s de t er min ed as foll ows:
B = Boar d e vent t r ace (tr ace s e vent s ass ocia te d wi th PCBs)
M = Miscellaneous State event trace
P=PulseCodedModulation(PCM)traceseventsassociatedwith
voi ce commun icati ons
C = CO Li ne (LCOB) St at es (t race s eve nts as soci ate d w it h CO Li ne
activity)
S = Station (STA) States (traces events associated with Station activity)
E = E rr or Mes...

5-26 R emo te Syst em Mo nit or
4. Then press to enable the trace. A similar screen displays:
Fi gure 5-7 : E nabl e Ev ent T race
5. To disableorturnoffaparticulartracemode,DONOTENTERa
specific board, CO Line, or Station Number (i.e.,
tsto disable station event trace).
6 . To have e vent t ra c es dis pl ayed on t he sc r ee n, you must f ir st e xit t he
MONitor mod e b y typingXat t hemon>pro mpt . Aft er you e xi t the
event(s), the trace begins as shown inFi gur e 5-8.
Modify Memory Command
The...

Remote System Monitor 5-27
B a ud Rat e Com m a nd
The Baud Rate command provides a co nven ie nt mea ns f or ch anging the
baud ra te, for the RS -232C port located on the Master Proces sor Board
(MPB), while in the Monitor mode. To change the baud rate type [B] plus
the d esi r ed baud ra te , t he n t he ent er ke y.
Exit the Monitor Mode
The Exit command terminates the current Remote Monitor
enable/disable session. If Event(s) Trace have been or are still enabled,
the event records are displayed only...