Home > Vodavi > Communications System > Vodavi Triad 1/2/3 Installation Manual

Vodavi Triad 1/2/3 Installation Manual

Here you can view all the pages of manual Vodavi Triad 1/2/3 Installation Manual. The Vodavi manuals for Communications System are available online for free. You can easily download all the documents as PDF.

Page 161

3-58 CO/ PBX Conne ctions
Primary Rate Interface Board (PRIB)
The PRIB board allows the network connection to a Primary Rate ISDN
interface. It provides one Primary Rate Interface circuit. Each circuit is
compris ed of 23 be are r channe ls an d one da ta channe l (23B+D). The
sys te m i nt er pr et s a ll B cha nnel s as tr unks/l in e a ppe ar ances . A m axim um
of six PRIBs can be installed into the system. The PRIB uses 24 time slots.
The PRIB conta ins an ISDN interfa ce circuit, control circuitry...

Page 162

CO/PBX Conn ections 3 -59
The PRIB conta ins 2 sw itches and 3 connectors. The Normal/Service
switch is used during maintenance to place the card in an Out-Of-Service
(OOS) mode. The clock selection s witch is u sed for control s ynchro nous
clock.
The sys te m can be eq uipp ed w it h si x (6 ) PRI I nte rf ace Boa rds and t he PRI B
can b e installed in any ca rd slot in the Ba sic KSU. The Phas e Locked Loop
Unit (PLLU) must be installed on the MPB when the PRIB is installed. The
DT MF 4- A boar d w...

Page 163

3-60 CO/ PBX Conne ctions
In sta l la ti on
1. Insert the PRIB card(s) into the desired BKSU card slot(s). Up to six
PRIB ca rds can be ins ta ll ed in a syst em . E ach PRI B pr ovid es 23 C O
Lines to the s ystem.
2. If installing a single PRIB, set SW2 to the ON position.
If multiple PRIBs are being installed, set SW2 to the ON position on
the f ir st c ar d a nd S W2 on a ll ot her c a rds to th e O FF pos it ion .
The PRIB comes with a clock cab le. This cable is us ed when multiple
PRIB a nd/or dig...

Page 164

CO/PBX Conn ections 3 -61
Functionality Description
Auto matic Num ber I dentification (A NI)i nform at ion from t he c a rr ie r is
tr ea te d e xac t ly t he same as an in bound I CL ID (Ca ll er I D) numbe r. Ca ll s
can be routed, placed in the unanswered call table, sent out to the CTI
Module p ort on a ke yse t, an d run throu gh the numbe r to name
tr ans la ti on t abl e . T heTri ad 3Sy st em prov ide s c all p rogr es s t one s i n t he
same manner as ICLID.
Dialed Number Identification Service...

Page 165

3-62 CO/ PBX Conne ctions
In sta l li ng t he DT MF- A Modu les
1. Unpack the DTMF-A Modules from their antistatic conductive bags in
the p ac ki ng b oxe s.
2 . Locat e t he CO NN5 and CO NN6 conne ctor s on t he DTMF -A modul e s.
3. Locate the CON4, CON5, CON8 and CON9connectors on the PRIB
(outlined).
4. Pos ition one of the DT MF-A m odule s so that the CON N5 and CON N6
connectors match up with the CON8 and CON9 connectors on th e
PRIB resp ectiv ely.
5. Pus h the DT MF -A mod ule onto thes e conn...

Page 166

CO/PBX Conn ections 3 -63
Fi g u re 3- 24 : P R I B w/ D TM F-A Mo d u le I ns ta ll at i o n 

Page 167

3-64 CO/ PBX Conne ctions
Basic Rate Interface Board (BRIB)
This interface provides four Basic Rate Interface circuits. Each circuit is
compris ed of two b earer ( 64Kbps ea ch) an d one da ta (16Kbp s) cha nnels
(2B+ D). Whe n a BRIB is programme d into theTri ad 3system, the system
inte rprets all B channe ls as trunk s. Thus , one BRIB which contains f our
2B+ D ci r c uit s p rov ide s ei ght li ne app ea ran ce s to theTr iad 3sys te m. A
maximum of e ight BRIBs ca n be installe d into the sys te m...

Page 168

CO/PBX Conn ections 3 -65
Figure 3-25: BRIB (Basis Rate Interface Board)
ON OF F
SW2 SWI TC HE S:
2
3
4 1 

Page 169

3-66 CO/ PBX Conne ctions
El ectron ic Key T el ephon e Service
Electron ic ke y te le phone se rv ice (E KTS) is a fea ture that can be prov id ed
on BRI ISDN to simulate standard analog DID lines. This allows several
differe nt numbe rs to be sha re d b y a single BRI circuit.
Due to the decline in telep hony tariffs, there is an increas in g de mand for
BRI ISDN features. A BRI circuit allows two simultaneous calls to be
handled, d ue to its techn ical s pecification. BRI circuits have two
B-Ch anne...

Page 170

CO/PBX Conn ections 3 -67
Conditions
BRI EKTS su ppor t is ava il abl e in Voda vi te le phone s yst ems wi th soft war e
ve rsion 3.0G a nd highe r.
Like DID, EKTS can be programmed to route calls using up to 7 digits. By
default, only the last three digits are analyzed for routing.
EKT S doe s not re qui re a l i ne a ppe ar ance on a spe cifi c t el ep hone beca use
the BRI terminates directly into the KSU.
Vodav i s uppor t s Bas ic E KTS. The EKT S ca ching opti on i s not s uppor te d by
Vodav i....
Start reading Vodavi Triad 1/2/3 Installation Manual

Related Manuals for Vodavi Triad 1/2/3 Installation Manual

All Vodavi manuals