Vodavi Starplus Dhs-l Technical Manual

Conference3-81
Chapt er 3 - Key Station Featu res , Opera tion , an d Programmin g
The conference in itia tor ma y force- releas e a conference mem ber or talk privately w ith a
conference member.
E
NHANCEDTEL EP HO N E S--
To force-release:
1. Press [FEAT ].
2. Dial [7] + [4].
3 . Di al th e s ta ti o n nu m ber o r p re ss the l ine bu tt o n t o r el ea se.
To ta lk priva te ly (conne cts se cond pa rty, places third p arty on hold):
1. Press [FEAT ].
2. Dial [5] + [7].
3 . Di al th e s ta ti o n nu m...

3-82Conference
Ch apter 3 - Key Station Featu res , Operation , an d P rog rammin g
Opera tion
1. Two CO lines are conferenced (F+[6]+[0]) at your station:
2. Press [FEAT ].
3. Dial [7] + [7]. At an Executive Telephone, the following display will be seen
momentarily.
4. If no f urthe r action is take n, the display re turns to idle status. At this tim e, the two
lines are conferenced.
To re jo i n t he unsup er vi se d c o nfe re nc e:
1 . At yo u r s ta ti o n , pre ss [ FE AT ] .
2. Dial [6] + [0].
Pro...

Day /Ni gh t Se rv ic e3-83
Chapt er 3 - Key Station Featu res , Opera tion , an d Programmin g
Co n dit io n s
†New confe re nce p artie s ma y only b e a dde d whe n the conferen ce controller is a
mem ber of th e conf erence.
†If an outs id e l i ne h angs up, t he li ne wi ll be r el ea sed.
Day/ Nig ht Service
Des crip ti on
The sy stem can b e p rogramm ed for Night Serv ice opera tion which a ffects incom ing CO
line ringing a nd rece iv e a ssignme nts. The Atte ndant of a T ena nt Gro up ma y ma...

3-84 D ire ct I nw a rd S y st e m A c ce ss ( D I S A )
Ch apter 3 - Key Station Featu res , Operation , an d P rog rammin g
Di re c t In wa rd Syst em Ac ce ss ( D ISA)
Des crip ti on
This feature allows you to remotely access system features such as System Speed Dial,
Line Acce ss for long distance calling, CO Line- to- CO Line Confe re ncin g, a nd Intercom
dialing. Anynumber of DISAlines maybe assignedincomingDISAaccessbasedon the...

Dis tin cti ve Rin gi n g3-85
Chapt er 3 - Key Station Featu res , Opera tion , an d Programmin g
Distinctive Ringin g
Des crip ti on
You may choose from four distinctive ringing tones to signal incoming calls. This allows
you to easily distinguish your calls from calls ringing at other stations near you.
Opera tion
ENHANCEDTEL EP HO N E S--
1. Press [FEAT ].
2. Dial [#] + [7].
3. Dial a ringing tone code (1-4).
E
XE CUTIVETELE PH O N ES--
1. Press [FEAT ].
2. Dial [#] + [7]. You will hea r the curre nt...

3-86Do Not Distu rb (DN D)
Ch apter 3 - Key Station Featu res , Operation , an d P rog rammin g
Do No t Disturb (D ND)
Des crip ti on
DND allows y ou to tem pora rily block a nd discontinu e ringing from incomin g CO ca lls a nd
intercom calls. You can activate DND while your telepho ne is idle or busy. Some stations
with a higher COS may override a stations DND condition.
When you have activated DND, you will hear a special intercom (stutter) reminder tone
when you lift th e ha ndse t or use the spe ake...

DSS C onso le3-87
Chapt er 3 - Key Station Featu res , Opera tion , an d Programmin g
DSS Conso le
Des crip ti on
Fo u r D S S c o nso l es may be ass ig ned to a s ta ti o n. E ac h DSS Co n so le u s es o ne di git al
st at ion por t. Up to 1 2 DS S co nsol es may be ins ta ll ed on a sy st em. The D SS consol e
buttons are progra mme d by the s ta tion us er us ing the F EAT + # + 4 comma nd, the n
pressing the button on the DSS to be programmed. All system feature codes may be
stored on the...

3-88End-to-End Signaling
Ch apter 3 - Key Station Featu res , Operation , an d P rog rammin g
End-to-End Signalin g
Des crip ti on
This fe ature allow s digital key te le phone stations to ge ne rate in- band D TMF tone s on ICM
calls to an on-site voice mail system. DTMF digits will only be sent to the SLT port when
connected to a 2- Port Analog Adap ter/E xpans ion tha t is programmed a s a VM PORT .
Feature Button
Co py
Fe at ure B ut ton Copy is pr ovi de d t o as si st i n pr ogr ammi ng m ult ip le...

Fe a t ure B ut t on3-89
Chapt er 3 - Key Station Featu res , Opera tion , an d Programmin g
5. The display then returns to the previous screen.
Programming
Des crip ti on
The E xecut iv e m odel s have 2 0 dual -col ore d p rogr amm abl e fea tur e but tons av ail ab le . A l l
sys tem feature cod es may be stored on th e p rogramm able fea ture buttons for
one-button operation. Certain programmed feature buttons will light when activated
(DND , C all F orw ard , D SS/BLF , etc. ), while others do not,...

3-90Feature Button
Ch apter 3 - Key Station Featu res , Operation , an d P rog rammin g
To prog ram a CO li ne but t on:
1. Se le ct [dir].
2. Enter CO line or station number (201-272, 301-372). The display shows:
3. Press [save].
To prog ram a syst e m fe at ure :
1 . Pr es s [ FEAT ]. T he dis pla y sh ows:
2 . Pr es s [ FEAT ]. F wi ll ap pea r on t he dis pl ay:
3. Dial the feature code.
4. Press [save].
To erase the conte nts of a prog ram mable fea ture button :
Press [save] instead of dialing a...