Vodavi Infinite Gk-816 Installation Manual

Infinite 816 Key Telephone System CO LINE ATTRJBUTES PROGRAMMING 
CO Line 
Attributes Programming (Cont’d) 
720.7 
DIALPULSE 
gmnming Steps 
lf the system is in the Programming mode, 
continue using program codes. If starting to 
program here, enter the Programming mode 
first (See Paragraph 700.4). 
Lf pulses per second (pps] and break/make 
ratios are to be changed: 
a Dial an asterisk I’] and [ 171 on the dial pad. 
b. Press CO line button for the line to be 
assigned dfal pulse. Then press the ap-...

Infinite 816 Key Telephone System SYSTEM PARAMETERS PROGRAMMTNG 
SECTION 730 
SYSTEM PARAMEI’ ERS PROGRAMMING 
730.1 SYSTEM CONFIGURATION 
Progmmming Steps 
If the system is in the Programming mode, 
continue using program codes. If starting to 
program here, enter the Progmmming mode 
first (See Paragraph 700.4). 
To change system data features: 
a Dialanasterisk[*]and[21]onthedialpad. 
b. Toggle them on or off so the LEDs light 
or 
extinguish for desired features. 
l LED on = enabled 
l LED off =...

SYSTEM PARAMETERS PROG-G Infinite 816 Key Telephone System 
System Configuration (Cont’d) 
Programminp Steps Description 
Alarm 
Enable - A yes entry (LED lit) means the 
system is programmed for alarm. Stations 
must then be programmed to receive the alarm 
signal. Alarm signaling and alarm detection 
must also be chosen. 
Default By default, this feature is disabled 
lLED off). 
Biwkgmund Music 
This feature must be enabled if Background 
Music is supplied to the system. 
Default: By default,...

Infinite 816 Key Telephone System SYSTEM PARAMETERS PROGRAMMING 
System Parameters ProgrammM Wut’d) 
730.2 SYSTEM TXMERS 
A. Exclusive Hold Recall 
Progr 
* 2 Steps 
lf the system is in the Programming mode, 
continue using program codes. If starUng to 
program here, enter the Programming mode 
first (See Paragraph 700.4). 
To change this timer: 
Dial an asterisk [*] and dial I221 
on the dial 1. 
2. 
3. 
B. 
pad. 
Dial three-digit number between 000 and 
255 (seconds). An entry of 000 disables 
the...

SYSTEM PARAMETZRS PROGRAMMXNG InJTnite 816 Key Telephone System 
System 
Parameters Programming (Cont’dl 
System Timers (Cont’d) 
D. 
Message Wait Reminder Tone 
k 
* g Steps 
To change this timer: 
1. Dial an asterisk (*I and 1251 on the dial pad. 
2. Dial 
two-digit entry between 00 and 99 
(minutes). An entry 
of 00 disables the 
timer. 
3. Press HOLD to enter data 
E. 
Pause Timer 
Programming Steps 
To change this timer: 
1. Dial an asterisk [*] are [26] on the dial pad. 
2. Dial one-digit entry...

Infinite 82 6 Key Telephone System SYSTEM PARAMElZRS PROGRAMMING 
System Parameters Programming (Cont’dl 
730.3 B/SECRETARY ASSIGN- 
MENTS 
grammUg Steps 
If the system is in the Programming mode, 
continue using program codes. If starting to 
program here, enter the Programmmg mode 
first (See Pamgraph 700.4). 
To program Executive/Secretary assignments: 
a. Dial an asterisk [*I and [27l on the dial pad. 
b. Press button for desired executWe/ secre- 
tary pa& assignment. Press the station 
button to...

SYSTEM PARAMETERS PROG-G Infinite 816 Key Telephone System 
System Parameter8 ProgramminQ (Cont’dl 
730.4 LOUD BELL CONTROL 
ROE . g Steps 
lf the system is in the Programrmng mode, 
continue using program codes. If starting to 
program here, enter the Programming mode 
first (See Paragraph 700.4). 
To program these assignments: 
a. Dial an asterisk [*I and [28] on the dial pad. 
b. First, press the station button of the sta- 
tion to be assigned ringing &ED will light). 
c. Press HOLD to enter data...

lrtfinite 816 Key Telephone System SYSTEM PARAMETERS PROGRAMMING 
System 
Parameters Programming (Cont’a) 
730.5 PBX DIALING CODES 
gramming Steps 
If the system is in the Programming mode, 
continue using program codes. If starting to 
program here, enter the Programming mode 
f&t (See Paragraph 700.4). 
To enter PBX Dialing codes: 
a Dial an asterisk [*I and 1301 on the dial pad. 
b. Press the program button to assign the 
first code. CO line 1 button is automat- 
ically lit for programming the i&t...

SYSTEM PARAMETERS PROGRAMMING Infinite 82 6 Key Telephone System 
System Parameters Programmiug (Cont’d) 
730.6 ATTEl’IDANT POSlTION 
R 
’ g Steps 
If the system is in the Programming mode, 
continue using program codes. If starting to 
program here, enter the ProgrammIng mode 
first (See Paragraph 700.4). 
To change the attendant positiorx 
a Dial an asterisk [*I and [3 11 on the dial pad. 
b. Press the station button of the station to 
be assigned as the system attendant. 
c. Press HOLD to enter data...