Vizio E420i-A1 HDTV User Manual

							1
5
Align the base with the neck and tighten three (3) M4 14mm 
screws into the base with phillips screwdriverPlace the TV on a stable, level surface.
Base InsTallaTIon conTInued (e420i) 
34  
						

							1
6
Base InsTallaTIon (e500i)
To install the base:
Place the TV screen-down on a clean, flat surface. To prevent 
scratches or damage to the screen, place the TV on a soft 
surface, such as carpet, rug, or blanket.
Align the neck piece with the bottom of the TV and slide it into 
place as shown above. Using a phillips screwdriver, tighten Four (4) M4 16 mm screws 
into the holes as shown above.
1
2  
						

							1
7
Align the base with the neck and tighten three (3) M6 12mm 
screws into the base with phillips screwdriverPlace the TV on a stable, level surface.
Base InsTallaTIon conTInued (e500i
)
34  
						

							1
8
Installing the TV on a Wall
To mount your TV on a wall, you will need a wall mount. Consult 
the information below to find the appropriate mount for your TV 
model:Installing a TV on a wall requires lifting. To prevent 
injury or damage to the TV, ask someone to help you.
Be sure the mount you choose is capable of supporting the 
weight of the TV. After you have determined that you have the 
correct mount for your TV, you can begin the installation.
To install yovur TV on a wall:
1 . Disconnect any cables connected to your TV.
2 .  Place the TV face-down on a clean, flat, stable surface. 
Be sure the surface is clear of debris that can scratch or 
damage  the TV.
3 .  Remove the base by loosening and removing the screws.
Attach your TV and wall mount to the wall, carefully following 
the instructions that came with your mount.  
 
Use only with a UL-listed wall mount bracket rated for the 
weight/load of this TV. See 
Appendix B - Specifications for the 
weight of this TV.
Wall Mount Screw Locaton - E420i
E420i-A1
Screw Size: M6
Screw Pitch: 1.0mm
Screw Length: 18mm
Hole Pattern: 200mm (V) x 200mm (H)  
						

							1
9
E500i-A1
Screw Size: M6
Screw Pitch: 1.0mm
Screw Length: 18mm
Hole Pattern: 400mm (V) x 400mm (H)
Wall Mount Screw Locaton - E500i  
						

							2
10
Controls and Connections
ReaR Panel
Rear Panel
Ethernet - Connect ethernet cable from home 
network.
Coaxial - Connect coaxial cable from cable, 
satellite, or antenna. Optical Audio Out - Connect optical/SPDIF audio 
device, such as home audio receiver. Stereo Audio Out - Connect RCA audio device, 
such as sound bar.
HDMI - Connect HDMI device (HDMI 4 is available 
on the E500i only).
Component/Compsite - Connect component or 
composite device. USB - Connect USB thumb drive to play photo, 
music, or video.  
						

							2
11
INPUT
MENU
CH ^
CH 
VOL ^
VOL 
^
^
Side Panel
Side Panel
POWER - Turn TV off or on.
MENU - Open the on-screen menu.CHANNEL UP/DOWN - Change the channel.
VOLUME UP/DOWN - Increase or decrease volume level.
INPUT - Change input source.  
						

							2
12
FR ont Panel
Front Panel
REMOTE SENSOR   
When using the remote, aim it directly at this sensor.  
						

							2
13
Remote ContRol
Remote Control
INPUT 
Change the currently-displayed input.
ARROW  
Navigate the on-screen menu.
ExIT 
Close the on-screen menu.CloSed CaPtionS
 
Open the closed caption menu.
A/V CONTROLS 
Control USB media player.
WIDE 
Switch the display mode.
MUTE 
Turn the audio off or on.
B
AC k 
Go to the previous on-screen menu. POWER
 
Turn TV on or off.
MENU
 
Display the on-screen menu.
INFO  
Display the info window.
D
ASH
 
Use with number pad to 
manually enter a digital 
sub-channel. (For example, 
18-4 or 18-5.) CHANNEL UP/DOWN
 
Change the channel. GUIDE
 
Display the info window.
LAST 
Return to the channel last viewed.
NUMBER P AD 
Manually enter a channel.
VOLUME UP/DOWN 
Increase or decrease loudness  
of the audio.
Ok 
Select the highlighted menu option.
V B UTTON 
Open the VIA dock.
APP LAUNCHER 
Quickly launch the pictured app.             
						

							2
14
Replacing the Batteries
1 . Remove the battery cover.
2 .  Insert two batteries into the remote control. Make sure that 
the (+) and (-) symbols on the batteries match the (+) and 
(-) symbols inside the battery compartment.
3 .  Replace the battery cover.