Vizio E322MV Razor Led Lcd Hdtv User Manual

							1
3
E322MV
3. Gently remove the stand neck. 
 
 
 
 
 
 
4.  Attach your TV and wall mount to the wall, carefully following the 
instructions that came with your mount. 
 
Use only with a UL-listed wall mount bracket rated for the weight/load o\
f 
this TV. See 
Appendix A - Specifications for the weight of this TV.  
						

							2
4
Controls and Connections
USB:Connect a USB thumb drive to view photos.
HDMI (1,2,3): Connect HDMI devices.
RCA Stereo   
Audio Out: Connect RCA cable to output audio to another device.
Component/  Composite: Connect component or composite device. 
Cable/Antennal: Connect RF/Coaxial connector from cable, antenna, or 
satellite box.
RGB PC: Connect RGB cable from computer. Use 3.5mm port to 
connect PC audio.
3.5mm PC   
Audio In: Connect 3.5mm cable from PC audio out when using 
RGB PC port to display PC output.
Optical Digital  Audio Out: Connect SPDIF/Optical audio device (soundbar, re-
ceiver, etc).
Rear Panel
Rear Panel
RGB PC
Cable/Antenna
USB
HDMI (1,2,3)
Component/ 
Composite
Optical Digital 
 
Audio Out
3.5mm PC Audio In RCA Stereo 
Audio Out  
						

							2
5
E322MV
Right Side Panel
Right Side Panel
Power
Menu
Channel Up
Volume Up
Channel Down Volume Down
Input
Power: Turn the TV on or off.
Menu: Display on-screen menu.
Channel Up/Down: Change the channel.
Volume Up/Down: Increase or decrease the loudness of the TV audio.
Input: Change the input device. Press once to display the 
Input menu. Continue pressing the button to highlight 
a different input source. Press Menu to confirm your 
selection.
Front Panel
Front Panel
Remote Control 
Sensor
VIZIO Light
Remote Control Sensor: When using the remote, point it directly at this 
sensor.
VIZIO Light: This light is white when the TV is on.  
						

							6
2E322MV
Power/Standby:Turn the TV on or off.
Input: Change the input device. 
A/V Controls: Control external device (CEC-enabled 
devices only).
Info: Display the Info Window.
CC: Open the Closed Captioning menu.
Menu: Display the on-screen menu.
Exit: Close the on-screen menu.
Arrow: Navigate the on-screen menu and episode 
guide.
OK: Select highlighted menu option.
Guide: Display the episode guide (digital channels 
only).
Back: Go to the previous on-screen menu op-
tions.
V Button: Launch the USB photo viewer.
Channel Up/ Down: Change the channel. With each press of 
the button, the channel will increase or 
decrease by one.
Volume Up/ Down: Increase or decrease the loudness of the 
TV’s audio.
Mute: Turn the sound off or on. When mute is 
activated, the TV’s audio is turned off.
Last: Return to the channel last viewed.
Number Pad: Use the number pad to manually enter a 
channel.
Dash (-): Use with number pad to manually enter a 
digital  
sub-channel. (For example, 18-4 or 18-5.)
Wide: Switch between display modes.
Remote Control
Power/Standby
A/V Controls
Info
Menu
Arrow
Channel  
Up/Down
Last
Number Pad
Wide
Mute
Volume 
Up/Down
OK
Exit
Input
Guide
Back
Dash (-)
CC
V Button
Remote Control  
						

							2
7
E322MV
Replacing the Batteries
1. Remove the battery cover by pressing 
gently on the “V” and pushing the 
cover away from the remote.
2.  Insert two AAA batteries. Make sure 
that the (+) and (-) symbols on the 
batteries match the (+) and (-) symbols 
inside the battery compartment.
3.  Replace the battery cover. 
 
• Use only good quality batteries.
• Inserting the batteries incorrectly may result in cracking or leakage   
   that may cause a fire or result in injury.
• Dispose of old or dead batteries in accordance with local hazardous   
   waste regulations.
• Keep batteries away from children and pets.    
						

							3
8Your HDTV can be easily connected to an external device:
•	DVD	or	Blu-Ray	player
•	 Video	game	console
•	 Cable	box
•	 External	antenna
•	 Or	other	device
Before You Begin
To connect a device to the HDTV:
1. Verify that the device has one of the following types of video ports 
available: 
Required	Device	Ports
HDMI RGB
RF/Antenna
Component
Composite	AV
2.  Ensure the TV has a matching port available.
3.  Ensure you have a cable that matches the available port. For example, if 
you are connecting a Blu-ray player with an HDMI port, be sure you have 
an HDMI cable.
Connecting Your Devices
Once you have determined the best available connection type on both your\
 
device and the TV, ensure you have the corresponding cable.
To connect a device to the TV:
1. Ensure both the TV and your device are off.
2.  Connect the device and the TV. Use the best available connection. See the 
Device Connection Chart on the next page. 
 
Ensure each end of the cable is securely connected.
3.  Turn the TV on by pressing the Power/Standby button on the remote.
4.  Turn your device on.
5.  When you are ready to use your newly connected device, press the INPUT 
button on the remote and select the connection type (HDMI, RGB, etc) from 
the on-screen menu. Press OK.
6.  Check the list of devices/connection types below for special instruction\
s:  
•	 Cable	TV	(without	cable	box/directly	from	wall)	
Perform	a	channel	scan.	See	
Scanning	for	Channels	on	page	12.	
•	 RGB	
Make	sure	the	desktop	resolution	on	the	PC	is	set	to	1920	x	1080.	Set	
the	Screen	Mode	to	Normal.		
•	 DVD	Player	with	DVI	
Connect	left	(white)	and	right	(red)	audio	cables	to	the	L	and	R	ports	
next	to	the	HDMI	ports	on	the	TV.
Connecting Your Devices  
						

							3
9
E322MV
Select One:
OR
OROR
OR
BETTER GOODBEST
HDMI
RF /
C OAXIAL
RGB
C OMPONENT
C OMPOSITE
AV DIGIT
AL
DIGIT AL /
ANAL OG
ANAL OG
ANAL OG
ANAL OG
Device	Connection	Chart
Select	one	of	the	connection	types.	
	
Use	the	cable(s)	shown	to	connect	 	
the	TV	to	your	device.  
						

							4
10
The first time you turn on the TV, the Setup App will guide you through each of 
the steps necessary to get your TV ready for use.
Before you begin the first-time setup:•	Your	TV	should	be	installed	and	the	power	cord	should	be	connected	
to	an	electrical	outlet.
•	 Have	your	remote	ready.	Ensure	the	batteries	are	inserted.
•	 Your	devices	should	be	connected.
To complete the first-time setup:
1.  Turn the TV on by pressing the 
Power/Standby button on the 
remote. 
 
The Setup App is displayed. 
 
Press the Right Arrow button on the 
remote to go to the next screen. 
2.  Use the Up/Down Arrow buttons on 
the remote to highlight your preferred 
language, then press Right Arrow. 
 
 
 
 
 
3.  Use the Up/Down Arrow buttons on 
the remote to highlight Home and 
press Right Arrow. 
 
 
 
 4. If the TV is connected to an external 
antenna, select Antenna, then press 
Right Arrow and go to step 5. 
 
If the TV is connected to a cable 
service without a set-top box (cable is 
connected directly from the wall outlet) 
select Cable, then press Right Arrow 
and go to step 5. 
 
If the TV is connected to a cable or 
satellite set-top box, press the EXIT 
button on the remote, then select the 
input to which your set-top box is 
connected (HDMI, COMP, or AV).
5.  Use the Up/Down Arrow buttons on 
the remote to highlight Scan, then 
press Right Arrow. 
 
The TV begins a channel scan. 
 
Wait for the channel scan to finish. 
 
6.  When the channel scan is complete, the Congratulations screen is 
displayed. 
 
The first-time setup is complete.
Completing the First-Time Setup  
						

							5
11
From the TV Settings Menu, you can:
•	Adjust	the	tuner	settings
•	 Adjust	the	TV	settings	for	use	with	
a	PC
•	 Set	up	the	parental	controls
•	 Change	the	on-screen	menu	
language
•	 Change	the	TV’s	date	and	time
•	 Turn	the	VIZIO	light	on	or	off
Navigating the On-Screen Menu
To open the on-screen menu, press the OK 
or MENU button on the remote. 
Use the Arrow buttons to highlight a menu 
option, and press the OK button to select 
that option. 
Setting Up Channels
From the tuner settings menu you can:
•	Change	the	signal	source
•	 Scan	for	new/additional	channels
•	 Start	a	new	channel	scan
•	 Remove	channels	from	the	master	list
Changing the Tuner Mode
Using this option, you can change the signal source for the coaxial (TV) input.
To change the signal source:
1.  Press the MENU button on the remote. 
The on-screen menu is displayed.
2.  Use the Arrow buttons on the remote 
to highlight the TV icon and press OK. 
The TV Settings menu is displayed.
3.  Use the Arrow buttons to highlight 
Tuner Settings and press OK.
4.  Use the Arrow buttons to highlight 
Tuner Mode.
5.  Use the Arrow buttons to change the 
setting to Cable or Antenna.
6.  Press EXIT.
Adjusting the TV Settings  
						

							12
5E322MV
Scanning for Channels
Before the TV can detect and display channels and their associated informatio\
n, 
you must scan for channels. A channel scan may also be necessary when the 
TV has been moved to an area where different free-to-air broadcast television 
channels are available.
To scan for channels:
1. Press the MENU button on the remote. 
The on-screen menu is displayed.
2.  Use the Arrow buttons on the remote 
to highlight the TV icon and press OK. 
The TV Settings menu is displayed.
3.  Use the Arrow buttons to highlight 
Tuner Settings and press OK.
4.  Use the Arrow buttons to highlight 
Auto Channel Scan and press OK.
5.  Use the Arrow buttons to highlight On 
and press OK. 
 
The channel scan begins.
6.  Wait for the channel scan to reach 
100%, then press EXIT.Scanning for New or Additional Channels
When a new channel becomes available in your area, you do not have to rescan 
all channels to add the new channel. Using the add channel feature, you can 
restrict the scan to new channels only. 
This is useful because your master channel list settings are preserved.
To scan for new channels:
1. Press the MENU button on the remote. 
The on-screen menu is displayed.
2.  Use the Arrow buttons on the remote 
to highlight the TV icon and press OK. 
The TV Settings menu is displayed.
3.  Use the Arrow buttons to highlight 
Tuner Settings and press OK.
4.  Use the Arrow buttons to highlight 
Additional Scan.
5.  Use the Left/Right Arrow buttons to 
change the option to On or Off .
6.  Perform a channel scan.