Vizio E321MV Razor Led Lcd Hdtv User Manual

							1
3
E321MV
3. Turn the attached thumbscrew until it 
is completely loosened. 
 
 
 
 
 
4.  Gently remove the stand neck. 
 
 
 
 
 
 
5.  Attach your TV and wall mount to the wall, carefully following the 
instructions that came with your mount. 
 
Use only with a UL-listed wall mount bracket rated for the weight/load o\
f 
this TV. See 
Appendix A - Specifications for the weight of this TV.  
						

							2
4
Controls and Connections
USB:Connect a USB thumb drive to view photos.
HDMI (1,2,3): Connect HDMI devices.
Component: Connect component device. 
Composite: Connect composite device.
3.5mm Stereo Out: Connect 3.5mm audio device.
Cable/Antennal: Connect RF/Coaxial connector from cable, antenna, or 
satellite box.
RGB PC: Connect RGB cable from computer. Use 3.5mm port to 
connect PC audio.
3.5mm PC   
Audio In: Connect 3.5mm cable from PC audio out when using 
RGB PC port to display PC output.
Optical Digital  Audio Out: Connect SPDIF/Optical audio device (soundbar,  
receiver, etc).
Rear Panel
Rear Panel
RGB PC
Optical Digital 
Audio Out 
USB
HDMI (1,2,3)
Composite
Component
3.5mm Stereo  OutCable/Antenna
3.5mm PC Audio In  
						

							2
5
E321MV
Right Side Panel
Right Side Panel
Power
Menu
Channel Up
Volume Up
Channel Down Volume Down
Input
Power: Turn the TV on or off.
Menu: Display on-screen menu.
Channel Up/Down: Change the channel.
Volume Up/Down: Increase or decrease the loudness of the TV audio.
Input: Change the input device. Press once to display the 
Input menu. Continue pressing the button to highlight 
a different input source. Press Menu to confirm your 
selection.
Front Panel
Front Panel
Remote Control 
Sensor
VIZIO Light
Remote Control Sensor: When using the remote, point it directly at this 
sensor.
VIZIO Light: This light is white when the TV is on. 
When the TV is off, the light is orange.  
						

							6
2E321MV
Power/Standby:Turn the TV on or off.
Input: Change the input device. 
A/V Controls: Control external device (CEC-enabled 
devices only).
Info: Display the Info Window.
CC: Open the Closed Captioning menu.
Menu: Display the on-screen menu.
Exit: Close the on-screen menu.
Arrow: Navigate the on-screen menu and episode 
guide.
OK: Select highlighted menu option.
Guide: Display the episode guide (digital channels 
only).
Back: Go to the previous on-screen menu op-
tions.
V Button: Launch the USB photo viewer.
Channel Up/ Down: Change the channel. With each press of 
the button, the channel will increase or 
decrease by one.
Volume Up/ Down: Increase or decrease the loudness of the 
TV’s audio.
Mute: Turn the sound off or on. When mute is 
activated, the TV’s audio is turned off.
Last: Return to the channel last viewed.
Number Pad: Use the number pad to manually enter a 
channel.
Dash (-): Use with number pad to manually enter a 
digital  
sub-channel. (For example, 18-4 or 18-5.)
Wide: Switch between display modes.
Remote Control
Power/Standby
A/V Controls
Info
Menu
Arrow
Channel  
Up/Down
Last
Number Pad
Wide
Mute
Volume 
Up/Down
OK
Exit
Input
Guide
Back
Dash (-)
CC
V Button
Remote Control  
						

							2
7
E321MV
Replacing the Batteries
1. Remove the battery cover by pressing 
gently on the “V” and pushing the 
cover away from the remote.
2.  Insert two AAA batteries into the 
remote control. Make sure that the (+) 
and (-) symbols on the batteries match 
the (+) and (-) symbols inside the 
battery compartment.
3.  Replace the battery cover. 
 
• Use only good quality batteries.
• Inserting the batteries incorrectly may result in cracking or leakage   
   that may cause a fire or result in injury.
• Dispose of old or dead batteries in accordance with local hazardous   
   waste regulations.
• Keep batteries away from children and pets.    
						

							3
8Your HDTV can be easily connected to an external device:
•	DVD	or	Blu-Ray	player
•	 Video	game	console
•	 Cable	box
•	 External	antenna
•	 Or	other	device
Before You Begin
To connect a device to the HDTV:
1. Verify that the device has one of the following types of video ports 
available: 
Required	Device	Ports
HDMI RGB
RF/Antenna
Component
Composite	AV
2.  Ensure the TV has a matching port available.
3.  Ensure you have a cable that matches the available port. For example, if 
you are connecting a Blu-ray player with an HDMI port, be sure you have 
an HDMI cable.
Connecting Your Devices
Once you have determined the best available connection type on both your\
 
device and the TV, ensure you have the corresponding cable.
To connect a device to the TV:
1. Ensure both the TV and your device are off.
2.  Connect the device and the TV. Use the best available connection. See the 
Device Connection Chart on the next page. 
 
Ensure each end of the cable is securely connected.
3.  Turn the TV on by pressing the Power/Standby button on the remote.
4.  Turn your device on.
5.  When you are ready to use your newly connected device, press the INPUT 
button on the remote and select the connection type (HDMI, RGB, etc) from 
the on-screen menu. Press OK.
6.  Check the list of devices/connection types below for special instruction\
s:  
•	 Cable	TV	(without	cable	box/directly	from	wall)	
Perform	a	channel	scan.	See	
Scanning	for	Channels	on	page	13.	
•	 RGB	
Make	sure	the	desktop	resolution	on	the	PC	is	set	to	1920	x	1080.	Set	
the	Screen	Mode	to	Normal.	
Connecting Your Devices  
						

							3
9
E321MV
Select One:
OR
OROR
OR
BETTER GOODBEST
HDMI
RF /
C OAXIAL
RGB
C OMPONENT
C OMPOSITE
AV DIGIT
AL
DIGIT AL /
ANAL OG
ANAL OG
ANAL OG
ANAL OG
Device	Connection	Chart
Select	one	of	the	connection	types.	
	
Use	the	cable(s)	shown	to	connect	 	
the	TV	to	your	device.  
						

							4
10
The first time you turn on the TV, the Setup App will guide you through each of 
the steps necessary to get your TV ready for use.
Before you begin the first-time setup:•	Your	TV	should	be	installed	and	the	power	cord	should	be	connected	
to	an	electrical	outlet.
•	 Have	your	remote	ready.	Ensure	the	batteries	are	inserted.
•	 Your	devices	should	be	connected.
To complete the first-time setup:
1.  Turn the TV on by pressing the 
Power/Standby button on the 
remote. 
 
The Setup App is displayed. 
 
Use the Up/Down Arrow buttons on 
the remote to highlight your preferred 
language, then press OK. 
2.  Use the Up/Down Arrow buttons on 
the remote to highlight Home Mode, 
then press OK. 
 
 
 
 
 
 
3.  Use the Up/Down Arrow buttons on 
the remote to highlight your time zone, 
then press OK. 
 
Press the Up/Down Arrow buttons on 
the remote to highlight Off  or On for 
daylight savings time, then press OK. 
 
 4.  If the TV is connected to an external 
antenna, select Antenna, then press 
OK and go to step 5. 
 
If the TV is connected to a cable 
service without a set-top box (cable is 
connected directly from the wall outlet) 
select Cable, then press OK and go to 
step 5. 
 
If the TV is connected to a cable or 
satellite set-top box, press the EXIT 
button on the remote, then select the 
input to which your set-top box is 
connected (HDMI, COMP, or AV).
5.  Use the Up/Down Arrow buttons on 
the remote to highlight Scan, then 
press OK. 
 
The TV begins a channel scan. 
 
Wait for the channel scan to finish. 
 
 
6.  When the channel scan is complete, 
the Congratulations screen is 
displayed. 
 
 
 
 
 
 
 
The first-time setup is complete.
Completing the First-Time Setup  
						

							5
11
From the TV Settings Menu, you can:
•	Change	the	input	source	or	
rename	inputs
•	 Set	up	channels
•	 Change	the	on-screen	menu	
language
•	 Change	the	TV’s	date	and	time
•	 Adjust	the	TV	settings	for	use	with	
a	PC
•	 Turn	the	VIZIO	light	on	or	off
Navigating the On-Screen Menu
To open the on-screen menu, press the OK 
or MENU button on the remote. 
Use the Arrow buttons to highlight a menu 
option, and press the OK button to select 
that option. 
Changing the Input Source
External devices such as DVD players, Blu-Ray Players, and video game console\
s 
can be connected to your TV. To display one of these devices on your TV, you 
must first change the input source in the on-screen menu.
To quickly access the Input Source menu, press the INPUT button 
on the remote.
To change the input source from the TV menu:
1.  Press the MENU button on the remote. 
The on-screen menu is displayed.
2.  Use the Arrow buttons on the remote 
to highlight the TV icon and press OK. 
The TV menu is displayed.
3.  Highlight Input and press OK. The 
Input menu is displayed.
4.  Use the Arrow buttons to highlight the 
input source you want to display and 
press OK.
Adjusting the TV Settings  
						

							12
5E321MV
Customizing Input Names
When you have multiple devices connected to your TV, it can become difficult to 
remember the inputs to which they are connected. Your TV features the ability to 
customize the names of these inputs to make them easy to remember. (Custom 
names have a 10-character limit.)
For example, 
HDMI 1 could be renamed as My Blu-ray.
To customize an input name:
1.  Press the MENU button on the remote. 
The on-screen menu is displayed.
2.  Use the Arrow buttons to highlight TV 
and press OK.
3.  Use the Arrow buttons to highlight 
Input and press OK.
4.  Use the Arrow buttons to highlight 
Input Naming and press OK.
5.  Use the Left/Right Arrow buttons on 
the remote to highlight the input source 
you wish to rename. 
6.  Use the Arrow buttons to highlight 
Custom Label and press OK. 
 
The on-screen keyboard is displayed.
7.  Use the Arrow and OK buttons to spell 
the custom input name.  
 
When you are finished, highlight OK 
and press OK.
8.  Press EXIT.
Setting Up Channels
From the channel menu you can:
•	Change	the	signal	source
•	 Start	a	new	channel	scan
•	 Scan	for	new/additional	channels
•	 Remove	channels	from	the	master	
list
•	 Change	the	audio	language
•	 Customize	channel	names