Vizio E320, 370, 420VT Razor Led Lcd Hdtv User Manual

							2
3
Component 1/ 
Composite: Connect component or composite video/audio de-
vice. When using composite, use only yellow, white, 
and red ports.
RGB PC/ 
Component 2: Connect RGB cable from computer, or use RGB-to-
component adapter to connect component video 
device.
DTV/TV: Connect RF/Coaxial connector from cable, antenna, 
or satellite box. Use the included RF Adpater when 
connecting your RF/coaxial cable.
RGB PC/ 
Component 2   Audio In: Connect 3.5mm connector for audio when using the 
RGB PC port or RGB-to-component adapter.
HDMI: Connect HDMI devices.
USB: Connect a USB thumb drive to view photos.
Digital Audio Out: Connect SPDIF/Optical audio device (Soundbar, 
receiver, etc).
3.5mm Audio Out: Connect 3.5mm audio device.
AC IN: Connect the included AC power cord.
Rear Panel
Please note that your rear panel will vary depending on your TV 
model number. Match your model number to the illustration below 
for the correct port illustration.
Rear Panel
HDMI
USB
Component 1/ Composite Digital  
Audio Out
RGB PC/ 
Component 2 3.5mm 
Audio Out
COMPONENT 1 (BETTER) RGB PC / COMPONENT 2Y
VP
b/CbP r/CrLR
USB
AUDIO 
OUT
DIGITAL  AUDIO  OUT
PC/COMPONENT  2
AUDIO
3
2
1 ARC
HDMI (BEST)
PC/COMPONENT 
2
AUDIO
ARC
USB
AUDIO 
OUT
3 4
2
1 DIGITAL 
AUDIO  OUT
HDMI (BEST)
E320VT 
E370VT E420VT
DTV/TV
RGB PC/ 
Component 2  Audio In
Power Cord
Controls and Connections  
						

							4
2E320VT / E370VT / E420VT
Front Panel
Front Panel
Remote Control Sensor
Remote Control Sensor: When using the remote, point it directly at this 
sensor.
Right Side Panel
Right Side Panel
Power
Menu
Channel Up
Volume Up
Channel Down
Volume Down
Input
Power: Turn the TV on or off.
Menu: Display on-screen menu.
Channel Up/Down: Change the channel.
Volume Up/Down: Increase or decrease the loudness of the TVs audio.
Input: Change the input device. With each press of the  
button, the TV will display a different input source.  
						

							2
5
E320VT / E370VT / E420VT
Remote Control
Power/Standby:Turn the TV on or off.
Input: Change the input device. With each press of the 
button, the TV will display a different input.
A/V Controls: Control USB photo slideshow.
Info: Display the Info Window.
CC: Open the Closed Captioning menu.
Menu: Display the on-screen menu.
Exit: Close the on-screen menu.
Arrow: Navigate the on-screen menu and episode guide.
OK: Select highlighted menu option.
Back: Go to the previous on-screen menu options.
Volume Up/Down: Increase or decrease the loudness of the TV’s 
audio.
Channel Up/Down: Change the channel. With each press of the but-
ton, the channel will increase or decrease by one.
Mute: Turn the sound off or on. When mute is activated, 
the TV’s audio is turned off.
Last: Return to the channel last viewed.
Number Pad: Use the number pad to manually enter a channel.
Dash (-): Use with number pad to manually enter a digital 
sub-channel. (For example, 18-4 or 18-5.)
Wide: Switch between display modes.
Power/Standby
A/V Controls
Info
Menu
Arrow
Channel  
Up/Down
Last
Number Pad
Wide
Mute
Volume 
Up/Down
OK
Exit
Input
Back
Dash (-)
CC
Remote Control   
						

							6
2E320VT / E370VT / E420VT
Replacing the Batteries
1. Remove the battery cover.
2.  Insert two AAA batteries into the 
remote control. Make sure that the (+) 
and (-) symbols on the batteries match 
the (+) and (-) symbols inside the 
battery compartment.
3.  Replace the battery cover. 
 
• Use only good quality batteries.
• Inserting the batteries incorrectly may result in cracking or leakage   
   that may cause a fire or result in injury.
• Dispose of old or dead batteries in accordance with local hazardous   
   waste regulations.
• Keep batteries away from children and pets.    
						

							3
7
Connecting Your Devices
Your HDTV can be easily connected to an external device:•	DVD	or	Blu-Ray	player
•	 Video	game	console
•	 Cable	box
•	 External	antenna
•	 Or	other	device
Before You Begin
To connect a device to the HDTV:
1. Verify that the device has one of the following types of video ports 
available: 
Required	Device	Ports
HDMI RGB
RF/Antenna
Component
Composite	AV
2.  Ensure the TV has a matching port available.
3.  Ensure you have a cable that matches the available port. For example, if 
you are connecting a Blu-ray player with an HDMI port, be sure you have 
an HDMI cable.
Connecting Your Devices
Once you have determined the best available connection type on both your\
 
device and the TV, ensure you have the corresponding cable.
To connect a device to the TV:
1. Ensure both the TV and your device are off.
2.  Connect the device and the TV. Use the best available connection. See the 
Device Connection Chart on the next page. 
 
Ensure each end of the cable is securely connected.
3.  Turn the TV on by pressing the Power/Standby button on the remote.
4.  Turn your device on.
5.  When you are ready to use your newly connected device, press the INPUT 
button on the remote and select the connection type (HDMI, RGB, etc) from 
the on-screen menu. Press OK.
6.  Check the list of devices/connection types below for special instruction\
s:  
•	 Cable	TV	(without	cable	box/directly	from	wall)	
Perform	a	channel	scan.	See	
Scanning	for	Channels	on	page	13.	
•	 RGB	
Make	sure	the	desktop	resolution	on	the	PC	is	set	to	1920	x	1080.	Set	
the	Screen	Mode	to	Normal.		
•	 DVD	Player	with	DVI	
Because	DVI	has	no	audio,	use	the	3.5mm	or	Optical	audio	out	port	on	
the	back	of	the	TV.  
						

							8
3E320VT	/	E370VT	/	E420VT
Select One:
OR
OROR
OR
BETTER GOODBEST
HDMI
RF /
C OAXIAL
RGB
C OMPONENT
C OMPOSITE
AV DIGIT
AL
DIGIT AL /
ANAL OG
ANAL OG
ANAL OG
ANAL OG
Device	Connection	Chart
Select	one	of	the	connection	types.	
	
Use	the	cable(s)	shown	to	connect	 	
the	TV	to	your	device.  
						

							4
9
The first time you turn on the TV, the Setup App will guide you through each of 
the steps necessary to get your TV ready for use.
Before you begin the first-time setup:•	Your	TV	should	be	installed	and	the	power	cord	should	be	connected	
to	an	electrical	outlet.
•	 Have	your	remote	ready.	Ensure	the	batteries	are	inserted.
•	 Your	devices	should	be	connected.
To complete the first-time setup:
1.  Turn the TV on by pressing the 
Power/Standby button on the 
remote. 
 
The Setup App is displayed. 
 
Press the Right Arrow button on the 
remote to go to the next screen. 
2.  Use the Up/Down Arrow buttons on 
the remote to highlight your preferred 
language, then press Right Arrow. 
 
 
 
 
3.  Use the Up/Down Arrow buttons on 
the remote to highlight Home and 
press Right Arrow. 
 
 
 
 
Initial Setup
Allow the VIZIO setup Wizard to
help you tune your channels. Welcome
Next
ExitEXIT
Initial Setup
Please select your language: English
Français
Español Language
Next
Back SelectExitEXIT
Initial Setup
Please select your input location:
Next
Back Select
Home
Retail Mode Setting
ExitEXIT
4. 
If the TV is connected to an external 
antenna, select Antenna, then press 
Right Arrow and go to step 5. 
 
If the TV is connected to a cable 
service without a set-top box (cable is 
connected directly from the wall outlet) 
select Cable, then press Right Arrow 
and go to step 5. 
 
If the TV is connected to a cable or 
satellite set-top box, press the EXIT 
button on the remote, then select the 
input to which your set-top box is 
connected (HDMI, COMP, or AV).
5.  Use the Up/Down Arrow buttons on 
the remote to highlight Scan, then 
press Right Arrow. 
 
The TV begins a channel scan. 
 
 
6.  Wait for the channel scan to finish. 
 
 
 
 
 
 
7.  When the channel scan is complete, 
the Congratulations screen is 
displayed. 
 
 
 
 
The first-time setup is complete.Initial Setup
Please select your input source:
Next
Back Select
Antenna
Cable Tuner
ExitEXIT
Initial Setup
Please connect your cable or
antenna to the DTV/TV input
Scan
Skip Scan Channel Scan
Next
ExitEXITBackSelect
Initial Setup
Channel Scan will take a few
minutes to complete.
Status: Scanning..
Analog Channels: 0
Digital Channels: 4 Channel Scan
ExitEXIT
Initial Setup
Congratulations !!
Initial Setup completed
Complete
BackNext
Completing the First-Time Setup         
						

							5
10From the TV Settings Menu, you can:
•	Setup	channels
•	 Change	the	input	source
•	 Change	the	on-screen	menu	
language
•	 Change	the	TV’s	date	and	time
•	 Adjust	the	TV	settings	for	use	as	a	
PC	monitor
•	 Enable	or	disable	the	CEC	settings
Setting Up Channels
From the channel menu you can:
•	Change	the	signal	source
•	 Customize	the	master	channel	list
•	 Scan	for	new/additional	channels
•	 Start	a	new	channel	scan
•	 Customize	channel	names
Changing the Signal Source
Using this option, you can change the signal source for the coaxial (TV) input.
To change the signal source:
1.  Press the MENU button on the remote. 
The on-screen menu is displayed.
2.  Use the Arrow buttons on the remote 
to highlight the TV icon and press OK. 
The TV Settings menu is displayed.
3.  Use the Arrow buttons to highlight 
Channels and press OK.
4.  Use the Arrow buttons to highlight 
Signal Source.
5.  Use the Arrow buttons to change the 
setting to Cable or Antenna.
6.  Press EXIT.
Adjusting the TV Settings  
						

							5
11
E320VT	/	E370VT	/	E420VT
Changing the Input Source
External devices such as DVD players, Blu-Ray Players, and video game console\
s 
can be connected to your TV. To use one of these devices with your TV, you must 
first change the input source in the on-screen menu.
To change the input device:
1. Press the MENU button on the remote. 
The on-screen menu is displayed.
2.  Use the Arrow buttons to highlight TV 
and press OK.
3.  Use the Arrow buttons to highlight 
Input and press OK. 
4.  Use the Arrow buttons to highlight 
Input Source and press OK.
5.  Use the Arrow buttons on the remote 
to highlight the input source you wish 
to display, then press OK. 
6.  The selected input source is displayed. 
 
 
 
 
 
 
 
 
To quickly change the input source, press the  INPUT button on the 
remote control.
Input Source
DTV/TV
AV
Component  1
Component  2
HDMI  1
HDMI  2
HDMI  3
HDMI  4
RGB
PHOT O
EXIT
LAST
Customizing and Removing Input Names
When you have multiple devices connected to your TV, it can become difficult to 
remember the inputs to which they are connected. Your TV features the ability to 
customize the names of these inputs to make them easy to remember. (Custom 
names have a 10-character limit.)
For example, 
HDMI 1 could be renamed as My Blu-ray.
You can also remove unused inputs from the input list, making selection of the 
correct input faster.
Customizing Input Names
To customize an input name:
1.  Press the MENU button on the remote. 
The on-screen menu is displayed.
2.  Use the Arrow buttons to highlight TV 
and press OK.
3.  Use the Arrow buttons to highlight 
Input and press OK.
4.  Use the Arrow buttons to highlight 
Input Naming and press OK.
5.  Use the Arrow buttons on the remote 
to highlight the input source you wish 
to rename, then press OK. 
6.  Use the Arrow buttons to highlight 
Input Naming and press OK. 
 
The on-screen keyboard is displayed.
7.  Use the Arrow and OK buttons to spell 
the custom input name.  
 
When you are finished, highlight OK 
and press OK.
8.  Press EXIT.  
						

							12
5E320VT	/	E370VT	/	E420VT
Removing Unused Inputs from the Input List
If you are not using an input and would like to remove it from the input list, you can 
do this from the Input menu.
To remove unused inputs:
1. Press the MENU button on the remote. 
The on-screen menu is displayed.
2.  Use the Arrow buttons to highlight TV 
and press OK.
3.  Use the Arrow buttons to highlight 
Input and press OK.
4.  Use the Arrow buttons to highlight 
Input Naming and press OK.
5.  Use the Arrow buttons on the remote 
to highlight the input source you wish 
to remove, then press OK. 
6.  Use the Arrow buttons to highlight 
Skip Input and press OK.
7.  Press EXIT. 
 
 
 
 
 
To restore an input to the list, go to the Input Naming screen and 
select Reset.
Customizing the Master Channel List
By customizing the master channel list, you can choose which channels ca\
n be 
displayed. Channels not in the list will not be available when watching \
broadcast 
television.
1. Press the MENU button on the remote. 
The on-screen menu is displayed.
2.  Use the Arrow buttons on the remote 
to highlight the TV icon and press OK. 
The TV Settings menu is displayed.
3.  Use the Arrow buttons to highlight 
Channels and press OK.
4.  Use the Arrow buttons to highlight 
Master Lists, then press OK. 
 
The master channel list is displayed.
5.  To add a channel to the list, highlight 
the channel and press OK. When a 
channel is available, a check mark is 
displayed next to the channel. 
 
To remove a channel from the list, 
highlight the channel and press OK. 
When the channel has been removed, 
the checkmark next to the channel will 
disappear. 
 
To add all available channels to the list, 
highlight Mark All and press OK. 
 
To remove all available channels from 
the list, highlight Unmark All and press 
OK. 
 
To include only digital channels in the 
list, highlight Digital Only and press 
OK.
6.  Press EXIT.