Vivitek Qumi Q7 User Manual

ii
Preface
Copyright
©2013 Vivitek Corporation.  is a trademark of Vivitek Corporation. Other 
trademarks are the properties of their respective owners. Values, weights and dimensions 
are approximate. Specifications are subject to change without prior notice.
Disclaimer
The information in this document is subject to change without notice.  The manufacturer 
makes no representations or warranties with respect to the contents here\
of and 
specifically disclaims any implied warranties of merchantability...

iii
Important Safety Information
Important: 
It is strongly recommended that you read this section carefully before u\
sing the Qumi. 
These safety and usage instructions that will make sure you enjoy many y\
ears of safe use 
of the Qumi. Keep this manual for future reference.
Symbols Used
Warning symbols are used on the unit and in this manual to alert you of hazardous 
situations.
The following styles are used in this manual to alert you to important information.
Note: 
Provides additional information...

iv
Qumi Installation Notice
• Allow at least a 50cm clearance around the exhaust vent.
Minimum 100mm
Minimum 500mm
• Make sure that the intake vents do not recycle hot air from the exhaust vent.
•  When operating the Qumi in an enclosed space, make sure that the surroun\
ding air 
temperature within the enclosure does not exceed operating temperature w\
hile the 
Qumi is running, and the air intake and exhaust vents are unobstructed.
•  All enclosures should pass a certified thermal evaluation to make...

v
Power Safety
• Only use the supplied power cord.
•  Do not place anything on the cord. Place the cord where it will not be in the way of 
foot traffic.
•  Remove the battery from the remote control when storing or not in use for a 
prolonged period.
Cleaning the Qumi
• Unplug the cord before cleaning. See  Cleaning the Qumi on page 45.
Note: 
The Qumi will be warm after usage. Allow Qumi to cool down before storing in a 
compartment.
Regulatory Warnings
Before installing and using the Qumi, read the...

vi
Table of Contents
Preface ..................................................................................................................ii
Chapter 1  At a Glance ................................................................1
Overview ................................................................................................................ 1
Accessories  ........................................................................................................... 3
Remote Control...

1
Chapter 1  At a Glance
Overview
Front/Top/Right View
Keypad
Keypad
See Keypad - On-Screen Display 
(OSD) buttons
Cooling Vent
Do not coverLens
Projection Lens
Zoom / Focus ring
Zoom / Focus the projected 
image
Cooling Vent
Do not cover
Right Cursor
Navigate and change settings in the 
OSD
Enter Cursor
Change settings in the OSD
Left Cursor
Navigate and change settings in the OSD
Up Cursor
Navigate and change settings 
in the OSD
Menu
Open and exit the OSD
Power Switch
Turn on/off the Qumi
Down Cursor...

2
Rear/Top/Left View
Bottom View
AC In
Connect the supplied power cord
Audio Out
Connect an audio cable to 
speakers or headphones
Audio in (L&R)
Connect the Audio in (L&R) 
cable from an audio device
Video
Connect the video cable from 
a video deviceVGA
Connect the VGA cable from a VGA device
IR Receiver
Receive IR signal from the remote control
HDMI 2
Connect a HDMI cable from a  HDMI device
HDMI 1/ MHL
Connect a HDMI / MHL cable from a HDMI / MHL device
USB
Connect an USB Flash Disc
Rubber Foot Pad...

3
Accessories
Along with the Qumi, the following accessories are included:
Remote Control 
(With one 3V CR2025 battery)
Standard HDMI Cable
VGA Cable
MHL cable
Regional Power Cord
 
WARRAN TY
 
Documentation Kit 
(User Manual, Quick Start Guide, Warranty 
Card)
Carrying Case
Lens Cap
WiFi Dongle (Optional)
Contact your dealer immediately if any items are missing, appear damaged, or if the unit 
does not work. It is recommended that you keep the original packing material should you 
ever need to return...

4
Remote Control
Important: 
1. Be sure nothing obstructs the path between the remote control and the Q\
umi. If the path 
between the remote control and the Qumi is obstructed, the signal can bo\
unce off certain 
reflective surfaces. 
2. The buttons and keys on the Qumi have the same layout and similar funct\
ions as the 
corresponding buttons on the remote control. This user’s manual describes the functions 
based on the remote control.
Qumi and Remote Control Buttons
The Qumi can be operated using...