Vivitek Projector Qumi User Manual

							5 
Setting Up the Remote Control 
The remot
e control  comes  wit h one (1)  3V  lithium  battery 
(C

R2025) . 
The battery  is pre-installed in the remote control. 
To begin using the remote control, remove the plastic tab (A) 
from  the battery  compartment.  Use a screwdriver to remove the 
battery cover by turning counter-clockwise 1/8 turn. Replacing the Remote Control
’s Batteries   1 . Remove the battery
compartment cover
by turning the cover
towards the arrow
(A). Then lift the
cover out towards
the arrow (B).. 2 . Remove the old
battery and insert
the new battery
with the positive
side  facing up. 3 . Install the cover   and turn
as shown in the
illustration.
Caution:  
1. Only use 3V lithium battery (CR2025).
2. Dispose of used batteries according to local ordinance regulations.
3. Remove the battery when not using Qumi for  prolonged periods.
Operating Range
  The remote control uses infrared (IR) transmission to control Qumi. It is necessary to  point 
the remote 
towards Qumi..
The  remote  control functions  properly  within a  radius  of 
 approximately  7  meters  (23 feet) and 
15  degrees  above  or  below  the Qumi  level  (If  the  remote  is  not  held  perpendicular  to  the  sides 
or rear of Qumi). 
If  Qumi  is unresponsive to the remote control, move closer  towards Qumi or it may be 
necessary to replace the battery. 
						

							6 Chapter 2  Getting Started  
What you need 
Qumi  can  be  connected 
to many  types  of  external  devices  and  peripherals.  To  play 
music, connect Qumi to an external or portable music player. To play films, connect Qumi to  a 
DVD, VCD  or  VHS  player  using HDMI interface.  To  play  video  and  display  photos,  connect
Qumi  to  a video  camera  and digital  camera  using HDMI interface. To  display  files  and  other
types  of  media,  connect  Qumi  to  peripherals  like  a computer  or USB drive.
These devices  can be connected  to  Qumi  using  an  appropriate  cable.  Make  sure  that 
the connecting device has an appropriate output  connector. See below for more connectivity 
information: 
						

							7 Se
tting  Up Qumi 
Connecting Peripherals by  HDMI 
Connect  HDMI-compatible peripherals to  Qumi using an HDMI  cable (included) 
						

							8 Inserting 
a USB device
  Connect a USB device 
to Qumi by inserting the device(s) into the appropriate port. 
Connecting Audio 
Connect 
earphones  or speaker to Qumi  by inserting into the  AV-in
 port.
Bluetooth Audio out is also available under Settings, Bluetooth. Turn Bluetooth "ON" and pair audio 
device.   
						

							9 Charging the 
Battery
  Follow the below steps to charge Qumi:   
Connect the AC power adapter to Qumi. 
Connect the other end of AC power adapter to a wall outlet. 
During charging, the blue light  on the AC power adapter  will be on. After  being fully charged, 
the blue light will automatically shut off.
 Note:  
The battery will be fully charged  in about  3   to 4 hours .   
						

							10 
Starting and Shutting Down Qumi
1 . Connect the AC  power  adapter to
Qumi .  Connect the other end of AC
power  adapter to a wall outlet.
Note:  
The  adapter  models  may  differ 
between 
countries. 2 .  
Press  power  button  to  turn   on 
Qumi.  
 When  AC   power  adapter   is
connected,  press  the  power 
button for   1   second.  
 When AC  power adapter  is not
connected,  press  the  power 
button for   3   seconds.  
Qumi  splash  screen  displays 
and connected devices 
are detected
at this time but not displayed. 
						

							11
  3 . If several input devices are connected, press the SOURCE
selection  (signal  source)  button 
on the  remote  control to
toggle between inputs. Please allow a few seconds for
projector to sync to each input.  HDMI:   H DMI  
 US B  1:   USB  Connection  
 USB   2:   USB  Connection  
4 .  
Press  power button to power off Qumi.  
5. When  “Power  off / Please  press  the  power  button  again”
message  appears,  press  power  button.  The  projector 
will turn  off.   Power off?  
Please  press  the  power  button 
again  
Adjusting the 
Projector Level 
Flip down the kickstand to adjust  the height of the 
projected image Using a Tripod 
Qumi can be used with a tripod by connecting the 
tripod to the bottom of Qumi. Many typical tripods 
can be connected.
  Supported Tripod Specifications: 
• Type: 
Tripod
• Socket size:  1/4"- 20, L6.3 mm 6.
To abort power off after pressing the power button once,
press another remote button apart from power button. 
						

							12 HappyCast 
- Android Setup
  Allows the mirroring of connected Android devices (smartphone, tablet). 
Option 1 (
Your 

Android device 
is connected to your Qumi WiFi hotspot ):  1.
Enable the Qumi’s Portable WiFi hotspot function (Inside the
Android operating system).
A. Qumi  Home  Screen   Settings  General   More  
Portable Hotspot
i. √ Tick Portable Wi-Fi hotspot
ii. Return to Splash screen by pressing the  Exit button
on the Remote several times.
2. Start  the  HappyCast  App  on  your  Qumi,  located  in  the  App
Folder.
 Ensure that you are connected to the Internet by
turning Wi-Fi ON by selecting WiFi Icon on Splash Screen
and Selecting "ON"
3. Scan 
 the  QR  code  (Quick  Response),  with  your  Android
device,  to  download  and  install  the  HappyCast  mobile  app.
Follow onscreen instructions to complete app installation.
4. After your Android device is connected to your Qumi’s WiFi
hotspot, start HappyCast  app to enable screen mirroring. Option 2 (
Your Android device
  and your Qumi are connected to the same home/office WiFi 
network ):
  1.
Ensure  that  your  Android  device  and your  Qumi  are
connected to the same home/office WiFi  network.
2. Start  the  HappyCast  App on  your  Qumi,  located  in  the 
Apps Folder.
3. Scan  the  QR  code  (Quick  Response),  with  your  Android
device  (may require a QR Reader App to do so)  to  download
and  install  the  HappyCast  mobile  App. Follow on-screen
instructions to complete  A

pp installation.
You  may  need to  allow  installation  of  Apps  from  unknown
sources on your Android device . 
Go  to  Settings  >  Security
> Unknown  sources  > Enable
4. Start HappyCast on  your Android device, and enable screen
mirroring. 
						

							13 HappyCast 
- iOS Setup
  Option 1 (
Your 
iOS device is connected to your Qumi WiFi hotspot ):  1.
Enable the Qumi’s Portable WiFi  hotspot function (Inside the Android operating system).
Qumi  Home Screen   Settings  General   More   Portable Hotspot
√ Tick Portable Wi-Fi hotspot
2. Start  the HappyCast  App on your  Qumi, located in the App s Folder on the Splash 
Screen.
3. On your iOS device, slide up from the bottom of the screen to display the control console.
The AirPlay button should appear, then click on it. Select the suitable device to switch on
the screen mirroring. 
						

							14 
Option 2 (
Your 
iOS device and your Qumi are connected to the same home/office WiFi network ):  1.
Ensure  that your iOS device  and your Qumi are under the same home/office Wi-Fi network
(Same Wireless Access Point  and SSID)
2. Start  the HappyCast  App on your  Qumi, located in the App s Folder.
3. On  your  iOS  device,  slide  up from  the  bottom  of  the  screen  to  display  the  control  console.
The  AirPlay 

button should appear (see below)  then turn Airplay on.  Select HappyCast
  to
switch  on 
the screen mirroring  to Qumi.
4. To Exit Screen mirroring, turn off Mirroring under Airplay on the mobile device.