Vivitek Projector H9080fd User Manual

							
11

ConTrols and funCTions2
2.1 H9080FD at a Glance
Figure 2-1 and Figure 2-2 show the key H9080FD components.
Zoom Ring
Focus RingProjection Lens
Horizontal Lens Shift
Vertical Lens Shift
Exhaust VentIntake Vent
Figure 2-1: H9080FD Front/Side View
EXHAUST VENT 
Warm air exits the projector through this vent. Ensure that it is not bl\
ocked.
INTAKE VENT 
Internal fans draw cool air into the projector through this vent.
ZOOM RING 
Rotate this to change the projected image size.
FOCUS RING 
Rotate this to focus the projected image.
PROJECTION LENS
Standard throw range (1.85 to 2.40:1) 
Short throw range (1.56 to 1.86:1) (Optional)
•
•
•
•
•
•
• 
						

							
1
ConTrols and funCTions
Figure 2-2: H9080FD Top/ Rear/ Bottom View
KEY PAD 
Initiate On Screen Display (OSD) menu and access control buttons for p\
rojector adjustment.
I/O PANEL 
Connect input and output devices to these ports.
ADJUSTABLE FEET 
Use these when the projector is installed in a table-top configuration t\
o level the image and/or adjust the projection 
angle.
CEILING MOUNT HOLES 
Use these to attach the ceiling bracket to the projector.
1.
2.
3.
4. 
						

							
1
ConTrols and funCTions
2.2 H9080FD I/O Panel
Figure 2-3 shows the H9080FD I/O panel.
1 
2
11 9 10 8 5 6 7 
43
Figure 2-3: H9080FD I/O Panel
HDMI 1 (Digital) 
HDMI 2 (Digital) 
HDCP-compliant digital video inputs for connecting an HDMI or DVI source\
.
POWER INPUT (100 to 240 VAC) 
Connect the H9080FD to power here. 
RGB 
Provides a standard, 15-pin VGA-style connection to either an RGB or com\
ponent high-definition source, or to a 
personal computer. The H9080FD automatically detects the input signal re\
solution.
COMPONENT 2 
Three BNCs for connecting component (YPbPr) video sources. 
COMPONENT 1/SCART (RCA connectors) 
Standard- or high-definition (480i/480p/576i/576p/720p/1080i/1080p) Co\
mponent (YPbPr) input for connecting a 
DVD/HD-DVD/BD player, HD set-top box or other SD/HD source. Also provide\
s RGB input for RGBS sources.
VIDEO 
Standard composite video input for connecting a VCR, laser disc player o\
r other composite video source. Also pro-
vides composite sync input for RGBS sources. 
S-VIDEO  
A standard S-Video input for connecting a DVD player, satellite receiver\
 or Super VHS (S-VHS) VCR. 
IR INPUT 
Wired input from a Niles- or Xantech-compatible, infrared (IR) repeate\
r system. 
TRIGGER 2 (3.5-mm, mini phono jack) 
Provides 12 (+/- 1.5) volt switched output for screen relays with 250m\
A current capacity and short protection. 
TRIGGER 1  
Provides 12 (+/- 1.5) volt switched output for screen relays with 250m\
A current capacity and short protection. 
RS-232 
A female, 9-pin D-sub connector for interfacing with a PC or home theate\
r automation/control system.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11. 
						

							
14
ConTrols and funCTions
2.3 H9080FD Key Pad
Figure 2-4 shows the H9080FD key pad, and the paragraphs that follow des\
cribe its functionality.
ENTER
MENU
SOURCE
1
2
3
4
Figure 2-4: H9080FD Key Pad
Cursor Keys (  ,  ,  ,  ):  
Use these buttons to select items or settings, adjust 
settings or switch display patterns.  
ENTER: Press to select a highlighted menu item or 
confirm a changed setting.
MENU:  
Press this button to show or hide the OSD menu.
SOURCE:  
Press to select a video source.  
HDMI1, HDMI2, RGB, COMP1, COMP2, VIDEO or 
S-VIDEO.
Power:  
Use the button to turn on/off the projector.
1.
2.
3.
4. 
						

							
15
ConTrols and funCTions
2.4 H9080FD Remote Control
Figure 2-5 shows the H9080FD remote control, and the paragraphs that fol\
low describe its functionality.
8
910
11
12
13
14
15
Figure 2-5: H9080FD Remote Control
ON: Use this button to turn the projector on.
OFF: Use this button to turn the projector off.
Source Selection Buttons:  
Press to select a video source.  
HDMI1, HDMI2, RGB, COMP1, COMP2, VIDEO or 
S-VIDEO.
Cursor Keys (  ,  ,  ,  ):  
Use these buttons to select items or settings, adjust 
settings or switch display patterns.  
ENTER: Press to select a highlighted menu item or 
confirm a changed setting.
Aspect Ratio Selection Button: Press this button re-
peatedly to select one of the following aspect ratios:   
•  16 : 9: For viewing 16:9 DVDs or HDTV programs in 
their native aspect ratio.  
•  Letterbox: For viewing LaserDisc movies or non-an-
amorphic DVDs on a 16:9 screen.   
•  4 : 3: Scales the input signal to fit 4:3 sources in the 
center of the screen.   
•  4:3 Narrow: Scales the input signal to fit 4:3 
sources in the center of the screen when using an 
anamorphic lens.   
•  Native: Displays source image in its native resolu-
tion without re-sizing or overscan.
TEMP: Press this button to adjust the color temperature.
OS: Press this button to switch to the next Overscan mode.
NR: Press this button to show or hide the Noise 
Reduction slider.
MP: Press this button to select where the OSD men-
us display on the screen.
SWAP: Press this button to swap the PIP image with 
active source image.
PIP: Press this button to switch to the next PIP image.
GAMMA: Press this button to switch to the next 
Gamma setting.
CONT, BRIGHT, SHARP: 
Press these buttons to show or hide the Contrast, 
Brightness, and Sharpness sliders.
USER 1, USER 2: Press these buttons to recall pre-
set User display settings 1 and 2.
MENU: Press this button to show or hide the OSD 
menu.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15. 
						

							
16

3.1 Remote Control
To install batteries in the remote control:
Slide the battery compartment cover in the direction of the arrow to rem\
ove it.
Install two AA batteries with the correct polarity.
Replace the cover. 
1.2.3.
 
 
 
 
 
 
Notes on Batteries
Make sure that the battery polarities are correct when installing the ba\
tteries.
Do not mix an old battery with a new one or different types of batteries\
.
If you will not use the remote control for a long time, remove the batte\
ries to avoid damage from battery leakage.
1.
2.
3.
•
•
•
3insTallaTion 
						

							
17
insTallaTion
Notes on Remote Control Operation
In most situations, you can simply point the remote control at the scree\
n which will reflect the IR signal from the re-
mote back toward the IR receiver on the projector. In some cases, howeve\
r, ambient conditions may prevent this. If 
so, point the remote control at the projector and try again.
If the effective range of the remote control decreases, or it stops work\
ing, replace the batteries with new ones.
The remote control may fail to operate if the infrared remote sensor is exposed to bright sunlight or fluorescent lighting.
60 
60 
Figure 3-1: IR Reception Angles
•
•
• 
						

							
1

3.2 Installation Considerations
Proper installation of your projector will ensure the quality of your di\
splay. Whether you are installing a projector tempo-
rarily or permanently, you should take the following into account to ens\
ure your projector performs optimally.
Installation Type
Choose the installation type that best suits your needs: front or rear s\
creen, floor mount or inverted mount. Table 3-1 
compares these various installation methods.
AdvantagesConsiderations
Front Screen, Floor Mount Installation
Easy to set up
Can be moved or changed quickly
Easy to access
•
•
•
Shares floor space with audience•
Front Screen, Inverted Mount (ceiling) Installation
Does not take up audience space
Projector is unobtrusive
Projector cannot be accidentally moved
•
•
•
Installation is more permanent 
Projector access is more difficult
•
•
Rear Screen, Floor Mount Installation
Projector is completely hidden
Projector is easily accessed
Usually good ambient light rejection
•
•
•
Requires separate room
Installation cost is usually higher
•
•
Rear Screen, Inverted Mount (ceiling) Installation
Projector is completely hidden
Usually good ambient light rejection
•
•
Requires separate room
Installation cost is usually higher
•
•
Rear Screen, Floor Mount with Mirror
Projector is completely hidden
Usually good ambient light rejection
Requires less space behind screen than other rear 
screen installations
•
•
•
Requires separate room
Installation cost is usually higher
•
•
Table 3-1: Projector Installation Options
Ambient Light
In general, minimize or eliminate light sources directed at the screen. \
Contrast ratio in your images will be noticeably 
reduced if light directly strikes the screen, such as when a shaft of li\
ght from a window or floodlight falls on the image. 
Images may then appear washed out and less vibrant.
insTallaTion 
						

							
1
insTallaTion
Throw Distance
Throw distance is the distance measured from the front of the projector \
to the screen. This is an important calculation 
in any projector installation as it determines whether or not you have e\
nough room to install your projector with a de-
sired screen size and if your image will be the right size for your scre\
en.
You can quickly estimate the throw distance by taking the width of the s\
creen and multiplying it by the lens throw ratio; 
see Figure 3-2. The result of this calculation tells you roughly how far\
 back the projector should be positioned from the 
screen in order to project a focused image large enough to fill the scre\
en.
Estimated Throw Distance 
Throw Distance (TD) = Screen Width (w) x Lens Throw RatioScreen width (W
)
TD
Figure 3-2: Estimated Throw Distance
Two models of the H9080FD are available, one with 1.56-1.86:1 lens (PA0\
3500-002) and the other with 1.85-2.40:1 
lens (PA03500-001).  With optional zoom adaptors throw ratios of 1.24 \
– 3.0 can be achieved.
The standard H9080FD offers throw ratios between 1.85:1 and 2.40:1. 
With the optional, short-throw lens, the H9080FD offers throw ratios bet\
ween 1.56:1 and 1.86:1. 
						

							
0

Vertical and Horizontal Position
Proper placement of the projector relative to the screen will yield a re\
ctangular, perfectly-centered image that com-
pletely fills the screen.
Ideally, the projector should be positioned perpendicular to the screen.\
The lens center should be aligned with either the top or bottom edge of \
the screen areas. The lens should be centered 
in the middle of the screen. See Figure 3-3.
Screen
HeightProjection Distance
Ceiling
x
Lens CenterLens Center
Ceiling Installation
ScreenHeight 
Floor
Lens Center
Projection Distance
Floor Installation
Lens Center
x
Figure 3-3: Projector Placement
NoteWhen installing, ensure that you use only UL Listed ceiling mounts.
For ceiling installations, use approved mounting hardware and M4 screws with a maximum screw 
depth of 8 mm (0.31inch).
The construction of the ceiling mount must be of suitable shape and strength. The ceiling mount 
load capacity must exceed the weight of the installed equipment, and as an additional precaution 
be capable of withstanding three times the weight of the equipment (not less than 48 kg) over a 
period of 60 seconds.
insTallaTion