Vivitek Projector H5095 Series User Manual

							— 12 — 
Installing the New Lens 
1.  Align the notches and correctly 
position the electrical contact pad as 
shown in the picture. 
Note: 
Pin of Electrical contact pins should 
be in the direction as shown in the 
picture. 
 
2.  Rotate the lens clockwise until you 
feel it click into place. 
  
E l e c t r i c a l c o n t a c t p i n s  
						

							– 13 – 
Starting and Shutting down the Projector 
1.  Remove the lens cap. 
 
2.  Securely connect the power cord 
and signal cable. When connected, 
the power led will turn red. 
 
3.  Turn on the lamp by pressing 
“” button on the rear of the 
projector or “” on the remote 
control. 
The PWR LED will now flash red.  
The startup screen will display in 
approximately 30 seconds. The first 
time you use the projector, you can 
select your preferred language from 
quick menu after the startup screen 
display. 
      
						

							— 14 — 
4.  If more than one input device is 
connected, press the SOURCE 
button and use ▲▼ to scroll among 
devices. 
 
 DVI: Digital Visual Interface 
 HDMI: High-Definition Multimedia Interface 
compatible 
 DisplayPort: Digital display interface 
 VGA 1 / 2: Analog RGB 1 / 2 
 Component Video: DVD input YCbCr / YPbPr , or 
HDTV input YPbPr  
 S-Video: Super video (Y/C separated)  
 Composite Video: Traditional composite video 
5.  When the “Power Off? /Press 
Power again” message appears, 
press the POWER button. The 
projector turns off.  
 Caution: 
1. Be sure to remove the lens cap before starting projector.  
2. Do not unplug the power cord until the READY LED stops flashing–indicating the projector has 
cooled down.   
						

							– 15 – 
Setting an Access Password (Security Lock) 
You can use the four (arrow) buttons to set a password and prevent unauthorized use of the projector. 
When enabled, the password must be entered after you power on the projector. (See Navigating the 
OSD on page 22 and Setting the OSD Language on page 23 for help on using OSD menus.) 
 Important: 
Keep the password in a safe place. Without the password, you will not be able to use the projector. 
If you lose the password, contact your reseller for information on clearing the password. 
 
1.  Press the MENU button to open the 
OSD menu. 
 
 
2.  Press the cursor ◄► button to move to 
the Settings 1 menu, press the cursor 
▲▼ button to select Advanced 1. 
3.  Press  (Enter) / ► to enter the 
Advanced 1 sub menu. Press the 
cursor ▲▼ button to select Security 
Lock. 
 
4.  
Press the cursor ◄► button to enter 
and enable or disable security lock 
function. 
A password dialog box automatically 
appears.    
						

							— 16 — 
5.  You can use the cursor buttons 
▲▼◄► 
either on keypad or IR remote control 
for password entry. You can use any 
combination including the same arrow 
five times, but not less than five. 
Press the cursor buttons in any order to 
set the password. Push the MENU 
button to exit the dialog box. 
 
 
6.  The password confirm menu appears 
when user presses the power-on key in 
case the Security Lock is enabled.  
Enter the password in the order you set 
it at step 5. In case you forget the 
password, please contact the service 
center.  
The service center will validate the 
owner and help reset the password.   
  
						

							– 17 – 
Adjusting the Projector Level 
Take note of the following when setting up the projector: 
 The projector table or stand should be level and sturdy. 
 Position the projector so that it is perpendicular to the screen. 
 Remove the Back Foot Holder on the rear adjuster foot before adjusting the projection  
angle. 
 Ensure the cables are in a safe location. You could trip over them.  
 
1.  To raise the level of the projector, 
twist the adjusters counter 
clockwise. 
 
2.  To lower the level of the projector, 
lift the projector and twist the 
adjusters clockwise. 
 
 
    
   
						

							— 18 — 
Adjusting Projected Image Position Using Shift 
 
The Shift feature provides a lens shift function that can be used to adjust the position of the projected 
image either horizontally or vertically within the range detailed below. 
Shift is a unique system that provides lens shift while maintaining a much higher ANSI contrast ratio 
than traditional lens shift systems. 
Adjusting the vertical image position 
The vertical image height can be adjusted between 60% and -20% ( 1080P) of offset position. Note 
that the maximum vertical image height adjustment can be limited by the horizontal image position. 
For example it is not possible to achieve the maximum vertical image position height detailed above if 
the horizontal image position is at maximum. Please consult the Shift Range diagram below for 
further clarification. 
 
 
Note: 
Suggest to loosen the screw before lens 
shift  adjustment and tighten up after 
finished adjustment.  Screen
Di st an ce(L)
Hx10 %
100 %
Screen Height
(H)
+60%
-2 0%
0%
108 0P
20%xH
60%xH  
						

							– 19 – 
Adjusting the horizontal image position 
With the lens in the center position the horizontal image position can be adjusted to the left or right by 
up to a maximum of 5% of the image width. Note that the maximum horizontal image height 
adjustment can be limited by the vertical image position. For example it is not possible to achieve the 
maximum horizontal image position if the vertical image position is at maximum. Please consult the 
Shift Range diagram below for further clarification. 
 
Shift Range Diagram 
 
 
When W and H at 0% offset position 
The max. H up shift=Hx60% 
The max. H down shift=Hx20% 
The max. W shift=Wx5% 
When max. W shift is Wx5%  
max. H shift=Hx55% 
When max. H shift is Hx60%  
max. W shift=Hx0% 
 Wx5%Wx5%   
						

							— 20 — 
Adjusting the Zoom, Focus and Keystone 
1.  Use the Image-zoom  
control (on the projector 
only) to resize the 
projected image and 
screen size. 
 
2.  Use the Image-focus  
control (on the projector 
only) to sharpen the 
projected image. 
 
3.  Use the KEYSTONE 
buttons (on the 
projector or the remote 
control) to correct 
image-trapezoid (wider 
top or bottom)  
effect. 
 
Remote control and OSD panel 
4.  The keystone control  
appears on the display.  
       
						

							– 21 – 
Adjusting the Volume 
1.  Press the Volume +/-  
buttons on the remote 
control.  
The volume control  
appears on the display. 
 
 
 
2.  Press the Left or Right 
Cursor buttons on the 
keypad to adjust 
Volume +/-. 
3.  Press the MUTE button 
to turn off the volume 
(This feature is 
available only on the 
remote).