Vivitek Projector DW882ST User Manual

							— 32 — 
Advanced 2 Feature 
Press the Menu button to open the OSD menu. Press ◄► to move to the Settings 1 menu. Press 
▲▼ to move to the Advanced 2 menu and then press Enter or ►. Press ▲▼ to move up and down 
in the Advanced 2 menu. Press ◄► to enter and change values for setting. 
 
ITEM DESCRIPTION 
Test Pattern Press the cursor ◄► button to enter and select internal test patternK 
H Image Shift Press the cursor ◄► button to enter and select H Image ShiftK 
V Image Shift Press the cursor ◄► button to enter and select V Image ShiftK 
  
						

							– 33 – 
Settings 2 Menu  
Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the 
Settings 2 menu. Press the cursor ▲▼ button to move up and down in the Settings 2 menu.  
 
ITEM DESCRIPTION 
Auto Source Press the cursor ◄► button to enter and enable or disable automatic source 
detection.  
No Singal Power 
Off (min.) 
Press the cursor ◄► button tç enter and enable or disable automatic shutdown of 
lamp when no signal.  
Auto Power On Press the cursor ◄► button tç enter and enable or disable automatic power On when AC 
power is suppliedK 
Lamp Mode Press the cursor ◄► button to enter and select the lamp mode for higher brightness 
or lower brightness to save lamp lifeK 
Reset All Press  (EnterF / ► to reset all settings to default values. 
Status Press  (Enter) / ► to enter the Status menu. See page 34 for more information on 
Status. 
Advanced 1 Press  (Enter) / ► to enter the Advanced N menu. See Advanced 1 Feature on 
page 35. 
Advanced 2 Press  (Enter) / ► to enter the Advanced 2 menu. See Advanced 2 Feature on 
page 46. 
 
Note : 
“Dynamic ECO”: Press BLANK button, or without any signal input in 30sec, Lamp will dim to 30% 
automatically.  
      
						

							— 34 — 
Status 
Press the cursor ▲▼ button to move up and down in the Settings 2 menu. Select the Status menu 
and press Enter or ► to enter. 
 
ITEM DESCRIPTION 
Active Source Display the activated source. 
Video Information Displays resolution/video information for RGB source and color standard for Video 
source. 
Lamp Hours  
(ECO, Normal) Lamp hour used information is displayed. ( ECO and Normal ) 
Software Version Showing system software version. 
  
						

							– 35 – 
Advanced 1 Feature 
Press the Menu button to open the OSD menu. Press ◄► to move to the Settings 2 menu. Press 
▲▼ to move to the Advanced 1 menu and then press Enter or ►. Press ▲▼ to move up and down 
in the Advanced 1 menu. Press ◄► to enter and change values for setting. 
 
ITEM DESCRIPTION 
Menu Position Press ◄► button to enter and select different OSD location. 
Translucent Menu Press ◄► button to enter and select OSD background translucent level.  
Low Power Mode Press ◄► to enter and turn Low Power Mode lff, ln or On By LanK 
Fan Speed 
Press the cursor ◄► button to enter and toggle between Normal and High fan 
speedsK  
Note: We recommend selecting high speed in high temperatures, high humidity, or 
high altitude (higher than 1500m/4921ft) areas. 
Lamp Hour Reset After replacing the lamp, this item should be reset. See page 36 for more information 
on Lamp Hour Reset. 
Projector ID  Press the cursor ◄► button to enter and adjust a two digit projector ID from 0 through 
VUK 
Network Press  (Enter) / ► to enter the Network menu. See page 36 for more information on 
Network. 
 
Note: 
About “On By Lan”, RJ45 will support to be waked up in this mode(Under 6W) but scalar won’t.   
						

							— 36 — 
Lamp Hour Reset 
 
Please refer to Resetting the Lamp on page 51 to reset the lamp hour counter. 
Network 
 
ITEM DESCRIPTION 
Network State Displays the network connection status. 
DHCP 
Press the cursor ◄► button to turn DHCP On or Off.  
Note: If you select DHCP Off, complete the IP Address, Subnet Mask, Gateway, 
and DNS fields. 
IP Address  Enter a valid IP address if DHCP is turned off. 
Subnet Mask Enter a valid Subnet Mask if DHCP is turned off. 
Gateway Enter a valid Gateway address if DHCP is turned off. 
DNS Enter a valid DNS name if DHCP is turned off. 
Apply Press  (Enter) / ► to confirm settings. 
 
   
						

							– 37 – 
LAN_RJ45 
 
Wired LAN Terminal functionalites 
Remote control and monitoring of a projector from a PC (or Laptop) via wired LAN is also possible. 
Compatibility with Crestron / AMX (Device Discovery) / Extron control boxes enables not only 
collective projector management on a network but also management from a control panel on a PC (or 
Laptop) browser screen. 
* Crestron is a registered trademark of Crestron Electronics, Inc. of the United States. 
* Extron is a registered trademark of Extron Electronics, Inc. of the United States. 
* AMX is a registered trademark of AMX LLC of the United States. 
Supported External Devices 
This projector is supported by the specified commands of the Crestron Electronics controller and 
related software (ex, RoomView ® ). 
http://www.crestron.com/ 
This projector is supported by AMX ( Device Discovery ). 
http://www.amx.com/ 
This projector is compliant to support Extron device(s) for reference. 
http://www.extron.com/ 
For more detail of information about the diverse types of external devices which can be connected to 
the LAN/RJ45 port and remote/control the projector, as well as the related control commands 
supporting for each external device, kindly please get contact with the Support-Service team directly.   
						

							— 38 — 
LAN RJ45 
1. Connect an RJ45 cable to RJ45 ports on the projector and the PC (Laptop). 
 
2. On the PC (Laptop), select Start → Control Panel  →Network and Internet. 
 
   
						

							– 39 – 
3. Right-click on Local Area Connection, and select Properties. 
 
4. In the Properties window, select the Networking tab, and select Internet Protocol (TCP/IP). 
5. Click Properties. 
  
						

							— 40 — 
6. Click Use the following IP address and fill in the IP address and Subnet mask, then click OK. 
 
7. Press the Menu button on the projector. 
8. Select Settings2→ Advanced1 → Network 
9. After getting into Network, input the following: 
 DHCP: Off 
 IP Address: 10.10.10.10 
 Subnet Mask: 255.255.255.0 
 Gateway: 0.0.0.0 
 DNS Server: 0.0.0.0 
10. Press  (Enter) / ► to confirm settings. 
11. Open a web browser (for example, Microsoft Internet Explorer with Adobe Flash Player 9.0 or higher). 
   
						

							– 41 – 
12. In the Address bar, input the IP address: 10. 10. 10. 10. 
13. Press  (Enter) / ►. 
The projector is setup for remote management. The LAN/RJ45 function displays as follows.