Vivitek Projector DW3321 User Manual

							— 32 — 
Pincushion 
Press the ENTER button to enter the Pincushion sub menu. 
1. Press the cursor ▲ / ▼ buttons to select one or both side and press ENTER. 
 
Note: 
Only one Pincushion setting will be stored so if you want to change from the previous direction to 
the other, the notice message will pop-up to remind you to reset the previous Pincushion setting. 
 
2. Press the cursor ▲ / ▼ / ◄ / ► buttons to adjust the desired side convex or concave. 
3. Press ENTER to save the settings. 
      
						

							 
– 33 – 
PC Detail Adjustment 
Press the ENTER button to enter the PC Detail Adjustment sub menu. 
Note: 
Customizing the settings in PC Detail Adjustment menu is only available when PC input source 
(analog RGB) is selected. 
 
ITEM DESCRIPTION 
Auto Press the ENTER/AUTO buttons on the control panel or the ENTER/AUTO buttons on 
the remote control to automatically adjust frequency, phase, and position. 
Frequency Press the cursor ◄ / ► buttons to adjust the A/D sampling number. 
Phase Press the cursor ◄ / ► buttons to adjust the A/D sampling clock. 
Horizontal Position Press the cursor ◄ / ► buttons to adjust the display position right or left. 
Vertical Position Press the cursor ◄ / ► buttons to adjust the display position up or down. 
Note:  
Some signals may take time to display or may not be displayed correctly. 
If the Auto Adjust operation cannot optimize the PC signal, try to adjust Frequency and Phase 
manually.  
						

							— 34 — 
3D Setting 
Press the ENTER button to enter the 3D Setting sub menu. 
 
ITEM DESCRIPTION 
3D Mode Press the cursor ◄ / ► buttons to select different 3D mode. 
3D Sync Press the cursor ◄ / ► buttons to select different 3D Sync. 
3D Sync Invert Press the cursor ◄ / ► buttons to enable or disable 3D Sync Invert.  
						

							 
– 35 – 
SYSTEM SETUP >> Basic Menu 
Press the MENU button to open the OSD menu. Press the cursor ◄ / ► buttons to move to the SYSTEM 
SETUP >> BASIC menu. Press the cursor ▲ / ▼ buttons to move up and down in the  
SYSTEM SETUP >> BASIC menu. Press the cursor ◄ / ► buttons to change values for settings. 
 
ITEM DESCRIPTION 
Presentation Timer Press the ENTER button to the presentation timer menu. See Presentation Timer on 
page 36. 
Language Press the cursor ◄ / ► buttons to select a different localization menu. 
Projection Press the cursor ◄ / ► buttons to choose from four projection methods. 
Menu Settings Press the ENTER button to enter the Menu Settings sub menu. See Menu Settings 
on page 36. 
Background Color  Press the cursor ◄ / ► buttons to select the background color when no input source is 
detected. 
Splash Logç Press the cursor ◄ / ► buttons to select a different startup screen. 
Auto Power Off Press the cursor ◄ / ► buttons to set the ~uto power çff timer. The projector 
automatically turns off if no input source is detected after the preset period of time. 
Sleep Timeê Press the cursor ◄ / ► buttons to set sleep timer. The projector automatically turns off 
after the preset period of time. 
Auto Search Press the cursor ◄ / ► buttons to turn on or off auto search.  
						

							— 36 — 
Presentation Timer 
The Presentation Timer function can indicate the presentation time on the screen to help you achieve 
better time management when giving presentations. 
 
ITEM DESCRIPTION 
Timer Period Press the cursor ◄ / ► buttons to select timer period (1 ~ 240). 
Timeê Press the cursor ◄ / ► buttons to enable or disable presentation timer. 
Menu Settings 
Press the ENTER button to enter the Menu Settings sub menu. 
 
ITEM DESCRIPTION 
Menu Display Time Press the cursor ◄ / ► buttons to set the menu display timer before the OSD times 
out. 
Menu Position Press the cursor ◄ / ► buttons to select from five OSD locations.  
						

							 
– 37 – 
SYSTEM SETUP >> Advanced Menu  
Press the MENU button to open the OSD menu. Press the cursor ◄ / ► buttons to move to the SYSTEM 
SETUP >> Advanced menu. Press the cursor ▲ / ▼ buttons to move up and down in the SYSTEM 
SETUP >> Advanced menu.  
 
ITEM DESCRIPTION 
High Altitude Mode 
Press the cursor ◄ / ► buttons to turn on or off high ~ltitude mode.  
Recommended to turn on when the altitude of the environment is higher than 1500m 
(4921ft). 
Audio Settings Press the ENTER button to enter the Audio Settings sub menu.  
See Audio Settings on page 38. 
Lamp Settings Press the ENTER button to enter the Lamp Settings sub menu. See Lamp Settings 
on page 38. 
Test Pattern Press the cursor ◄ / ► buttons to select test pattern. 
Closed Caption Press the ENTER button to enter the Closed Caption sub menu.  
See Closed Caption on page 39. 
Low Power Mode 
Press the cursor ◄ / ► buttons to set Low Power Mode Off, On or On by LAk.  
Note: When Low Power Mode set to Off and On by LAN, VGA OUT terminal can 
output signal during projector in Standby mode. 
Network Settings Press the ENTER button to enter the Network Settings sub menu.  
See Network Settings on page 39. 
Reset All Settings Press the ENTER button to reset all settings to default values. 
Air Filter Timer 
Reset Press the ENTER button to reset air filter timer. 
Remote ID Press the cursor ◄ / ► buttons to select remote ID to fit the current remote ID 
settings.  
						

							— 38 — 
Audio Settings 
Press the ENTER button to enter the Audio Settings sub menu. 
 
ITEM DESCRIPTION 
Mute Press the cursor ◄ / ► buttons to turn on or off the speaker.  
Volume Press the cursor ◄ / ► buttons to adjust the audio Volume. 
Out Press the cursor ◄ / ► buttons to select audio output connector. 
Note: When select Off, the default sound is output from speakers. 
 
Lamp Settings 
Press the ENTER button to enter the Lamp Setting sub menu. 
 
ITEM DESCRIPTION 
Lamp Mode Press the cursor ◄ / ► buttons to adjust lamp brightness. 
Reset Lamp Timer Press the ENTER button to reset the Lamp Hour after the lamp is replaced. 
Total Lamp Hour Displays the number of equivalent hours the lamp has been in use. 
Note: Lamp Mode is not allowed to adjust when 3D mode is activated.  
						

							 
– 39 – 
Closed Caption 
Press the ENTER button to enter the Closed Caption sub menu. 
 
ITEM DESCRIPTION 
Closed Caption 
Enable Press the cursor ◄ / ► buttons to turn on or off Closed Caption. 
Caption Version Press the cursor ◄ / ► buttons to select the Caption Version. 
 
Network Settings 
Press the ENTER button to enter the Network Settings sub menu. 
 
ITEM DESCRIPTION 
Wired LAN Press the ENTER button to enter the Wired LAN sub menu. See Wired LAN on page 
40. 
Wireless LAN Press the ENTER button to enter the Wireless LAN sub menu.  
Remote Desktop Press the ENTER button to enable remote access to the computer. 
Projection Login 
Code Press the cursor ◄ / ► buttons to turn on or off the projection of the login code. 
Broadcasting Press the ENTER button to enter the Broadcasting sub menu. 
AMX Device 
Discovery Press the cursor ◄ / ► buttons to turn on or off discovery of AMX devices. 
MAC Address Press the ENTER button to enter the MAC address. 
  
						

							— 40 — 
Wired LAN 
Press the ENTER button to enter the Wired LAN sub menu. 
 
ITEM DESCRIPTION 
Status Displays the network connection status. 
DHCP 
Press the cursor ◄ / ► buttons to turn DHCP On or Off.  
Note: If you select DHCP Off, complete the IP Address, Subnet Mask, Gateway, and 
DNS fields. 
IP Address  Enter a valid IP address if DHCP is turned off. 
Subnet Mask Enter a valid Subnet Mask if DHCP is turned off. 
Default Gateway Displays the default Gateway address on the network. 
DNS Server Enter a valid DNS name if DHCP is turned off. 
Apply Press ENTER to confirm settings. 
For simplicity and ease of operation, the projector provides diverse networking and remote management 
features. 
The LAN/RJ45 function of the projector through a network, such as remotely manage: Power On/Off, 
Brightness and Contrast settings. Also, projector status information, such as: Video-Source, Sound-Mute, 
etc. 
 
Wired LAN Terminal Function 
Remote control and monitoring of a projector from a computer through a wired LAN is possible. 
Compatibility with Crestron / AMX (Device Discovery) / Extron control boxes enables projector 
management through a network as well as a remote computer’s browser.  
* Crestron is a registered trademark of Crestron Electronics, Inc. of the United States. 
* Extron is a registered trademark of Extron Electronics, Inc. of the United States. 
* AMX is a registered trademark of AMX LLC of the United States.  
						

							 
– 41 – 
Supported External Devices 
This projector supports command inputs from a Crestron Electronics controller and related software 
(RoomView ®), for further information: http://www.crestron.com/ 
This projector supports the AMX (Device Discovery), for further information: http://www.amx.com/ 
This projector complies and supports Extron device(s), for further information: http://www.extron.com/ 
For more information on the external devices and their related control commands supported through the 
LAN/RJ45 port and the projector’s remote/control function contact the service support team directly. 
LAN RJ45 
1. Connect an RJ45 cable to the RJ45 port on the projector and computer. 
 
2. On the computer, select Start >> Control Panel >> Network and Internet. 
 
 
 
The Network and Internet screen displays.