Vivitek Projector DU900 User Manual

							1819
Turn On 
Press ON on the remote control or STBY on the projector. The power and lamp LED indicator flashes blue to 
show warm-up.
When the power and lamp LED indicator lights are blue and the projector \
light is turned on, this mean that 
the projector is ready for use. Refer to Page 9 [Indicator LED] if the LED indicator flashes red. Please 
contact the Vivitek licensed dealer if the problem cannot be solved.
Changing the OSD Language 
The projector can display English and Simplified Chinese menus. Press MENU to show OSD and press ▲▼ 
to select control items. Press ▲▼ to select language you want to use. Press Enter to confirm the selection.
AC Outlet
USAEuropeChina
• Caution: 
Ensure that the power net meets the power requirements of the projector.
•  Warning: 
Do not attempt operation if the AC supply and cord are not within the specified voltage and
power range.
•  Caution:
Once the projector is switched to standby, the lamp cooling fans will continue to run for approximately
five minutes to ensure that the projector and lamp have sufficiently cooled, at which point the
fans will automatically decrease to standby. To avoid thermal stress that can lead to premature lamp
failure, never unplug the power cord while the lamp cooling fans are run\
ning. Never unplug the power
cord to power down the projector, first switch off the power switch and then unplug the power cord.
Make sure the power system (including the projector and power supply system) is properly grounded before connecting to the AC 
power. The projector may be damaged without the grounding circuit. 
This is a high-brightness and high-watt projector. Do not modify the AC power cord or replace the power cord arbitrarily to avoid 
causing damages to the projector or safety problems.
Before Using the Projector
Befor Using the Projector  
Before Using the Projector
Befor Using the Projector  
						

							2021
Start Using the Projector-Operation
Select the Input Source 
Press the INPUT Source button on the remote control to se-
lect the input source.
Select the Aspect Ratio 
Press ASPECT to adjust the aspect ratio of the image.
Use OSD (OnScreen Display)
1. Press the MENU button on the remote control or the control panel to show\
 the OSD main menu.
2.   Press  ◄
 or  ►
 to select the sub-menu. 
3.   Press  ▲ or ▼ to select the item of the sub-menu. 
4.   The selected item will be highlighted, press  ▲ or ▼ to select the settings of the item and press ENTER 
or the ENTER on the control panel to adjust the value of the item.
5.   Press MENU to return to the previous menu.
6.   Press MENU in the main menu or RETURN to close the OSD menu.
OSD Menu Tree
1st Layer 2nd Layer 3rd Layer Selections Factory
Reset
MAIN Aspect Ratio
16:9 /LetterBox / 4:3 / 4:3 Narrow / 16:10 
/ 5:4 / Native 16:10
Presets Recall Preset
Preset A/ Preset B / Preset C / Preset D / 
Default
Save Preset Preset A/ Preset B / Preset C / Preset D
Overscan Off / Crop / Zoom Off
3D Control 3D Format
Off / Auto / Side by Side (Half) / Top and 
Bottom /Dual Channel Auto
DLP Link Off / On Off
3D Swap Normal / Reverse Normal
Dark Time 1ms / 1.5ms / 2ms / 2.5ms 2ms
Sync Delay 0~200 100
1080p24 3D Display 96Hz / 144Hz 96Hz
Input Select HDMI1 / HDMI2 / VGA / COMP1 / 
COMP2 /SDI / HDBaseT / SDI HDMI1
Resync
IMAGE Picture Mode
Bright / Presentation / Video Bright
Brightness 0 ~ 200 100
Contrast 0 ~ 200 100
Saturation 0 ~ 200 100
Hue 0 ~ 200 100
Sharpness 0 0
Noise Reduction 0  0
Adjusting the Projection Mode 
The projection mode has influence on the direction of the projected image and cooling. The projection mode 
option can be used to change the direction of the projected screen and the cooling fan speed to ensure that 
the projector is properly cooled. The improper projection mode settings may trigger over heating or reduce 
the service life of lamps and elements. Please make sure the correct pro\
jection mode is set when installing 
the projector. 
Press the MENU button on the remote control or the control panel to bring up OSD and set the projection 
mode, Select CONTROL→ Projection Mode 
Front Table
Installed on the desk and the projection screen will be shown in the nor\
mal direction.
Rear Table
Installed on the desk. The image will be projected from behind the screen and the projected image will be 
overturned.
Front Ceiling
Ceiling mounted. The image will be projected from the front of the screen and will be overturned on 180 de-
gree. The cooling fan speed will be adjusted.
Rear Ceiling
Ceiling mounted. The image will be projected from behind the screen and the projected image will be over-
turned on 180 degree. The cooling fan speed will be adjusted.
Rear Tabletop 
The projector is installed upwards and the image is projected upwards. The cooling fan speed will be ad-
justed.
Lens Adjustment
The projector has the features to control the screen size, location and focus. Press the Lens Shift button on 
the Keypad or the remote control to shift zoom in/out or focus on the pr\
ojected image.
When you need to operate the Lens Shift, Zoom or Focus from the Keypad, please use Enter key and it will 
bring up the OSD for lens shift adjustment.  Then again press the Enter key on the  OSD Menu to Zoom and 
Focus.
Press Lens shift Key on remote for direct control.
Vertical Lens Shift 
Press ▲▼
 to move upward or downward to adjust the projected image vertically. 
Horizontal Lens Shift 
Press  ◄►
 to move to the right or left to adjust the projected image horizontally\
.
Zoom In/Out 
Press ZOOM+/ ZOOM- key to enlarge (zoom in) or reduce (zoom out) the\
 projected image size.
Focus 
Press FOCUS+/ FOCUS- key on the control panel to make the image clear. 
Start Using the Projector
Befor Using the Projector  
Start Using the Projector
Befor Using the Projector  
						

							2223
1st Layer2nd Layer 3rd Layer Selections Factory
Reset
ALIGNMENT Lens Control
Center Lens
Warp
Horizontal  Keystone
-350 ~ 350 0
Vertical Keystone  -200 ~ 200 0
Rotation -20 ~ 20 0
Pincushion / Barrel -100 ~ 100 0
Top Left corner X: +/- 192, Y +/- 120 0
Top Right corner X: +/- 192, Y +/- 120 0
Bottom Left corner X: +/- 192, Y +/- 120 0
Bottom Right corner X: +/- 192, Y +/- 120 0
Reset reset all warp item to defaults 0
Blanking To p
0 ~ 360 0
Bottom 0 ~ 360 0
Left 0 ~ 534 0
Right 0 ~ 534 0
Reset reset all blanking item to defaults 0
Edge Blend Status  
White Level
To p
0~500 200
Bottom 0~500 200
Left 0~800 200
Right 0~800 200
Black Level
To p 0~32 0
Bottom 0~32 0
Left 0~32 0
Right 0~32 0
ALL         <      > 0~32 0
RED       <  0  > 0~32 0
GREEN  <  0  > 0~32 0
BLUE      <  0  > 0~32 0
Reset reset all Edge Blending White and Black 
level to defaults
Test Patterns White / Black / Red / Green / Blue / 
ChessBoard / CrossHatch / V Burst / H 
Burst / ColorBar1st Layer
2nd Layer 3rd Layer Selections Factory
Reset
ADVANCED Color Space
Auto / REC709 / REC601/ RGB PC / 
RGB Video Auto
Gamma 1.0 / 1.8 / 2.0 / 2.2 / 2.35 / 2.5 / S-Curve 2.2
Color
Temperature 5500K / 6500K / 7500K / 9300K / Native
Native
Dynamic
Contrast Off / On
off
Adaptive 
Contrast Off / On
Off
RGB Adjust  Red Gain
0 ~ 200 100
Green Gain
Blue Gain
Red Offset
Green Offset
Blue Offset
Fine Sync H Position
0 ~ 200 100
V Position
Phase
Tracking
Sync Level
HSG HSG
Off / On off 
Red
HUE (0~200)
Saturation (0~200)
Gain (0~200) 100
Green
Blue
Cyan
Magenta
Yellow
White
Red Gain (0~200) / Green Gain (0~200)
Blue Gain (0~200)
Reset
LAMPS Lamp Mode
Eco / Normal / Power Power
Power 0~20 (77%~100%) 92%
Lamp Select Single / Dual / Lamp1 / Lamp2 Dual
High Altitude Off / On Off
Lamp1/2 Status
Lamp1/2 Run Time
Start Using the Projector
Start Using the Projector  
Start Using the Projector
Start Using the Projector  
						

							2425
OSD Menu - Main Selection
OSD Menu - MAIN
1st Layer2nd Layer 3rd Layer Selections Factory
Reset
CONTROL Language
English /簡中 / Korean
OSD Settings Menu Position
Top Left / Top Right / Bottom Left / 
Bottom Right / Center Center
Menu Transparency 0% / 25% / 50% / 75% 0%
Time Out Always On / 10 Seconds / 30 Seconds / 
60 Seconds 30s
Message Box Off / On On
Blank Screen Splash / Black / Blue / White Splash
Projection Mode Front Tabletop / Front Ceiling / Rear 
Tabletop / Rear Ceiling Front
Tabletop
Auto Power Off Off / On Off
Auto Power On Off / On Off
Startup Splash Off / On On
Trigger-1 Screen / 16:9 /LetterBox / 4:3 / 4:3 
Narrow / RS232 Screen
Trigger-2 Screen / 16:9 /LetterBox / 4:3 / 4:3 
Narrow / RS232 16:9
Auto Source Off / On Off
Infrared Remote Off / On On
Network Standby Power
Off / On On
DHCP Off / On
IP XXX.XXX.X.X
Subnet Mask XXX.XXX.XXX.X
Gateway X.X.X.X
DNS X.X.X.X
Apply Settings
SERVICE Model Name
Serial Number
Software
Version 1
Software
Version 2
FPGA Version
Active Source
Signal Format
(Timing Info)
Lamp1 Run
Time
Lamp2 Run
Time
Factory Reset
Start Using the Projector
Start Using the Projector  
Start Using the Projector
Start Using the Projector  
						

							2627
Preset
There are 10 display modes, 6 preset and 4 user assigned,  that can be used to adjust the display.  Preset 
modes include:  Picture/Brightness/Contrast/Saturation/Hue/Sharpness.  The user assigned modes are as-
signed by the user and memorized by the system. 
Input Selection 
This function is same as the shortcut key on the remote control. You can use the remote control or this func-
tion to select the correct input source.
 
HDMI
HDMI input from PC or media equipment.
SDI
SDI input from PC or media equipment.
VGA
 
RGB signal from PC.
Component / BNC  
Analog interface in media equipment.
HDBaseT  
HDBaseT output of PC, media equipment or HDbaseT transmitter.
Resync
You can use this function to set auto synchronization for the input signa\
l.
3D Control 
Set the 3D format and sync method. The projector detects the type of the connected input signal and  
provides relevant options for setting. The unavailable option is displayed using light green texts. Before per-
forming 3D setting, make sure that the input signal is connected. When theres no input signal, no 3D setting 
shall be performed.
3D Format
Select this option and press the Enter button to enable 3D replay and se\
t 3D option.
•  Off  
Turn off the 3D Display Mode. When Auto, Side by Side, Top/Bottom or Frame Sequential is selected, the 
3D Mode will be turned on. To turn off the 3D Mode, select Off and press the Enter button. 
•  Auto 
Enable the 3D format to automatically detect the formats of Frame Packin\
g, Top/Bottom and Side by Side.  
This function may only be enabled for the input signal below:  
The input signal is HDMI 1.4a 3D.  
The HDMI 1.4a 3D signal connects to the projector through the HDBaseT transmitter. 
•  Side by Side(Half)  
Manually switch the 3D Format to Side by Side. This option is only applicable to the HDMI input signal or 
the HDMI signal sent by using the HDBaseT transmitter.    
•  Top/Bottom: Manually switch the 3D Format to Top/Bottom. This option is only applicable to the   
HDMI input signal or the aforementioned signal sent through the HDMior H\
DBaseT transmitter. 
DLP Link
Set to activate or deactivate the DLP Link sync.
Aspect Ratio 
This function allows the user to adjust the aspect ratio of the image.
With a normal input of 16:10, the aspect ratio:
16:9 /LetterBox / 4:3 / 4:3 Narrow / 16:10 / 5:4 / Native
Native input 
16:10
Native input 
4:3
Output aspect ratio
4:3 Narrow
Output aspect ratio
5:4Output aspect ratio
16:9
Output aspect ratio
Native 
Output aspect ratio
4:3
Output aspect ratio
Letterbox
Output aspect ratio
16:9Output aspect ratio
5:4Output aspect ratio
4:3
Output aspect ratio
4:3 NarrowOutput aspect ratio
Native Output aspect ratio
Letterbox
Cropped portion of the image
Start Using the Projector
Start Using the Projector  
Start Using the Projector
Start Using the Projector  
						

							2829
OSD Menu - IMAGE
Picture Model 
Use ◄►
 to select a picture model. 
Bright: The highest brightness output mode is suitable for the occasion where hi\
gh brightness is needed.
Presentation: The best image effect is suitable for the presentation or picture.
Video: The best color mode is suitable for playing video.
Brightness 
Use  ◄►
 to increase or decrease the brightness of the image. 
Contrast 
Use  ◄►
 to adjust the contrast of the projected image.
Note
The  brightness  and  contrast  controls  affect  each  other.  To  obtain  the  best  setting,  fine-tune  of  the  brightness  setting  might  be 
needed after adjustment of the contrast.
Saturation 
Use  ◄►
 to adjust the saturation level of the color (the higher the level, the\
 higher the saturation).
Sharpness 
Use  ◄►
 to adjust the sharpness. The purpose of this adjustment is to change the value of the high-fre-
quency detail.
Hue 
Use  ◄►
 to adjust the level of hue for reproduction of the true color. 
Noise Reduction 
Use  ◄►
 to adjust the noise of the projected image. This function is suitable for removing the noise of the im-
age in interlaced scanning input. Generally, noise reduction can lower the value of the high-frequency detail 
and make the image softer.
 
3D Swap
If the 3D imaged viewed through the 3D glasses for the left and right eyes are inverse, set the \
3D Swap to 
Inverse. If the images are normal, keep the current setting as Normal.\
Dark Time
Manually switch the Dark time for glasses tolerance.
Sync Delay
Manually switch the sync delay for glasses tolerance.
1080P 24 3D Display
Set the 3D 24Hz image frame rate to 96fps or 144fps.This option is only applicable when the input signal is 
24Hz.
Note:
The projector provides DLP Link and 3D IR sync. After the 3D Mode is enabled, the built-in DLP Link or external 3D IR trans-
mitter can be used to synchronize the signal of the 3D glasses. Or, you may turn off the DLP Link sync signal and only select the 
external 3D IR transmitter to synchronize the 3D signal.
Important reminders: 
The people listed below should be aware when watching 3D images: Children under six years in age 
People who are allergic to light, unhealthy and have the history of cardiovascular diseases
People who are tired or lack of sleep 
People who are under the impact of drug or alcohol 
Normally,  it's  safe  to  watch  3D  images.  However,  some  people  might  feel  uncomfortable.  Refer  to  the  guidelines  revised  and  re-
leased  by  the  3D  League  on  December  10,  2008.People  who  watch  3D  images  need  to  take  a  break  for  at  least  5  to  15  minutes 
every thirty minutes or one hour
Start Using the Projector
Start Using the Projector  
Start Using the Projector
Start Using the Projector  
						

							3031
Fine Sync 
Adjust the sync of signal to get proper display on screen.
• H and V Position : Adjust horizontal and vertical position of image if not at center.
•  Phase : Adjust the phase of signal sampling clock if noise is visible.
•  Tracking : Adjust the frequency of signal sampling clock if flicker or vertical banding visible on screen.
•  Sync Level : Adjust the voltage level of signal if projector loss sync during scenes \
where the signal drops 
below black.
HSG
Provide the capability to define custom color Gamut by setting Hue, Saturation and Gain. 
• on – enable HSG adjust function
•  Off - disable HSG adjust function.
•  Red : Adjust Hue, Saturation and Gain of Red color.
•  Green : Adjust Hue, Saturation and Gain of Green color.
•  Blue : Adjust Hue, Saturation and Gain of Blue color.
•  Cyan : Adjust Hue, Saturation and Gain of Cyan color.
•  Magenta : Adjust Hue, Saturation and Gain of Magenta color.
•  Yellow : Adjust Hue, Saturation and Gain of Yellow color.
•  White : Adjust White Gain of Red, Green and Blue color.
•  Reset : Reset all the setting of HSG to default value.
OSD Menu - LAMP
Lamp Mode
Use the  ◄►
 button to select the ECO, Normal or Custom Power Level mode. 
•  Normal  
Projection is carried out using the normal lamp power to obtain the brig\
htest projection display.
•  ECO 
Projection is carried out in the energy saving mode to ensure the longes\
t service life of the lamp.
•  Power 
Use the  ◄►
 button to select the Custom Power Level. The projector allows a custom power level equal to 
77%~100% of the lamp power in the Normal mode. This function is available only when the lamp power is 
set to Custom Power Level. It cannot be selected (highlighted) in the \
Normal or ECO mode.
OSD Menu - ADVANCED IMAGE
Color Space 
This function allows you to change the corresponding color space for the\
 input signal. In most cases, the 
correct color space can be selected automatically by Auto mode. If the selection is not correct, you can use a 
specific color space forcibly by selecting one of the following options: 
•  Auto 
The projector detects the input signal and switches to the corresponding\
 color space automatically.
•  REC601  
Set the color space to ITU-R BT.601.
•  REC709  
Set the color space to ITU-R BT.709.
•  RGB-PC 
Use the RGB color space and set the black to 0, 0, 0 RGB while set the w\
hite to 255, 255, 255 RGB (if an 
8-bit image is used).
•  RGB-Video: Use the RGB color space and set the black to 16, 16, and 16 RGB wh\
ile set the white to 235, 
235,  235 (if an 8-bit image is used) to correspond to the luminance value defined in the digital component 
standard.
Gamma 
When the ambient light is too bright and may affect the display of the details in the darker area of the image, 
you can select from the following gamma options to adjust the chrominanc\
e of the image.
Optional Gamma table : 1.0 / 1.8 / 2.0 / 2.2 / 2.35 / 2.5 / S-Curve
Color Temperature
Use  ◄►
 to adjust the color temp of the projected image.
Dynamic Black 
Use the  ◄►
  function to turn on/off Dynamic Black.
Adaptive Contrast 
Use  ◄►
 to enable and disable the adaptive contrast function.
Start Using the Projector
Start Using the Projector  
Start Using the Projector
Start Using the Projector  
						

							3233
Lens Control 
Select this function to open the Lens Control menu for adjustment of Zoom, Focus or Shift. You can use the 
Enter button to switch the Zoom/Focus or Shift menu. Use ◄►
 to adjust zooming and horizontal shift of the 
lens, or use ▲▼ to adjust focusing and vertical shift of the lens.
Center Lens 
This is the lens calibration function. The projector adjusts the lens parameters for the lens memory function 
to work and sets the lens to the default center position.
Warp
•  Keystone 
Adjust the keystone of the projected picture.  
Keystone
Adjust
 
•  Rotation  
Adjust the Rotation of the projected picture.  
Rotation
Adjust
 
Power
User can select custom power % of lamp.
Lamp Select
Use the  ◄►
 button to select the single-lamp or dual-lamp mode. 
•  Dual  
Enable the dual-lamp projection mode.
•  Lamp 1 
Use Lamp 1 for projection. The system switches to Lamp 2 if Lamp 1 is abnormal in activation.
•  Lamp 2 
Use Lamp 2 for projection. The system switches to Lamp 1 if Lamp 2 is abnormal in activation.
•  Single: Use the single-lamp mode for the projection. The lamp is not specified in this mode, the projector 
selects the lamp that has the least operation hours automatically whenev\
er it is turned on.
Note
1.  In  the  Lamp  1  or  Lamp  2  mode,  the  projector  will  switch  to  another  lamp  when  the  set  lamp  becomes  abnormal.  The  corres-
ponding LED indicator of the lamp will flash simultaneously for seconds and light up. 2. When the lamp mode is set to Single, the 
setting will become valid upon turn-on of the projector next time. 3. Quick switch of the lamp mode may affect the life of the lamp. 
The projector will disable the lamp mode function (highlighted) every time when a switch is conducted till the switch of the lamp 
mode is completed. The lamp mode options will not be available before th\
e switch of the lamp mode is completed.
High Altitude 
Use this function to control the cooling fan of the projector. You can set it to OFF or ON, the default setting is 
OFF.
keystone, the projector can operate normally when this function is set to OFF. The projector detects ambient 
temperature by default to regulate the cooling fan speed. When the temperature rises, the cooling fan speeds 
up (with higher noise) to exhaust the internal heat energy out of the projector and ensure its normal oper-
ation. However, the projector may turn off automatically if it is used in an environment at excessively high 
temperature or in an area at a high altitude. In this case, you can enab\
le this function by setting it to ON and 
have the cooling fan operate at a higher speed to control the internal t\
emperature of the projector.
Lamp 1/2 Status
This is status of lamp turn on or not.
Lamp 1/2 Run Time
Total lamp used hours of Lamp1 or Lamp2.
OSD Menu - ALIGNMENT
Start Using the Projector
Start Using the Projector  
Start Using the Projector
Start Using the Projector  
						

							3435
Edge Blend
Edge blend function requires multiple projectors simultaneously displaying on the same screen. Use this to 
adjust the uniformity of the images.
To use this function, Edge Blending must be enabled on both projectors.
Status On/Off  To enable or Disable Edge Blend function.
• White Level  
White Level is used to compensate for the lack of pure white output from\
 projectors, due to light leaking 
to the projection screen. When projecting White , the hot area where the\
 two images overlap project twice 
the projectors white output levels.  
The solution is to adjust the White Level. First make sure that the unit\
s connected to the projectors are 
outputting black. Then increase the White Level (Top, Bottom, Left, Right) until the non-overlap areas 
brightness matches the overlap area.  
To adjust White Level   
1. Press Menu to activate menu 
2. Press  ◄►
 to select Alignment and press Enter. 
3. Press  ◄►
 to select Edge Blend and press Enter. 
4. Press  ◄►
 to select White Level and press Enter. 
5. Adjust the black level in zone A by setting the Selected Area (Top, Bottom, Left, Right) to match the  
    black levels in zones B and C. You can also use Adjust (All, Red, Green, Blue) to set all primary colors.
•  Black Level   
Black Level is used to compensate for the lack of pure black output from\
 projectors, due to light leaking to 
the projection screen. When projecting black , the hot area where the tw\
o images overlap project twice the 
projectors black output levels.  
The solution is to adjust the Black Level. First make sure that the units connected to the projectors are out-
putting black. Then increase the Black Level (Top, Bottom, Left, Right) until the non-overlap areas bright -
ness matches the overlap area.  
To adjust Black Level  
1. Press Menu to activate menu 
2. Press  ◄►
 to select Alignment and press Enter. 
3. Press  ◄►
 to select Edge Blend and press Enter. 
4. Press  ◄►
 to select Black Level and press Enter. 
5. Adjust the black level in zone A by setting the Selected Area (Top, Bottom, Left, Right) to match the      
    black levels in zones B and C. You can also use Adjust (All, Red, Green, Blue) to set all primary colors.
 Note:
  *Four corners, black level uplift adjustment function is not available.
  *Corner blending, black level uplift adjustment function is not available.
Test Pattern 
The built-in image is provided for installation and adjustment. You can select Test Pattern on OSD or the 
TEST PATTERN button on the remote control to display the test pattern. Press the button again to display 
the next test pattern or press the RETURN button to exit the test patter\
n.
• 
Pincushion/Barrel  
Adjust the Pincushion / Barrel of the projected picture.  
Pincushion
Adjust
 
Barrel
Adjust
 
•  Top Left Corner  
Adjust the Top left corner of the projected picture  
Top Left Corner
Adjust
 
•  Top Right Corner  
Adjust the Top right corner of the projected picture  
Top Right Corner
Adjust
 
•  Bottom Left Corner 
Adjust the bottom left corner of the projected picture  
Bottom Left
Corner Adjust
 
•  Bottom Right Corner  
Adjust the bottom right corner of the projected picture  
Bottom Right 
Corner Adjust
 
Blanking
Use this function to adjust the edges of the image and hide unwanted sec\
tions of the screen.
• TOP 
Press ◄►
 on the remote control to adjust the top blanking area on the projected \
image.
•  Bottom 
Press  ◄►
  on the remote control to adjust the bottom blanking area on the projec\
ted image.
•  Left 
Press ◄►
 on the remote control to adjust the left blanking area on the projected\
 image.
•  Right 
Press ◄►
  on the remote control to adjust the right blanking area on the project\
ed image.
•  Reset 
It will reset all the blanking functions to the default settings that is\
 without any blanking functions enabled.
Start Using the Projector
Start Using the Projector  
Start Using the Projector
Start Using the Projector  
						

							3637
Auto Power Off 
This function is set to OFF by default. When it is set to ON and no input signal is received within 20 minutes, 
the projector will turn off automatically.
Auto Power On 
This function is set to OFF by default. When it is set to ON and connected to an AC power source the project-
or will turn on automatically. When you plug the power cable of the projector in an AC socket attached with a 
switch, you can use this function and the power switch (instead of the \
remote control) to turn on the projector. 
Set this function to OFF if you do not need to use it.
Startup Splash 
Use the  ◄►
 button to turn on/off the Startup Logo.  You can choose Splash, Black, Blue or White from OSD.
Default setting is: Splash
Trigger 1 & 2 
The projector is provided with a set of trigger output. When automatic screen equipment is available, connect 
it to the screen trigger of the projector by using the cable. The screen automatically turns on when the pro-
jector is powered on. There is a 2-3 second delay before this function is activated.
Screen:   When the Screen aspect ratio is selected, the trigger outputs 12V power.
16:9:     When the 16:9 aspect ratio is selected, the trigger outputs 12V power.
Letterbox:    When the aspect ratio having the letterbox shape is selected, the trigge\
r outputs 12V power.
4:3:      When the 4:3 aspect ratio is selected, the trigger outputs 12V power.
4:3 Narrow:   When the 4:3 Narrow aspect ratio is selected, the trigger outputs 12V po\
wer.
RS232:   When the RS232 aspect ratio is selected, the trigger outputs 12V power.
Auto Source 
Use the ◄►
 button to turn on/off Auto source Search
Infrared Remote
Use the  ◄►
 button to turn on/off Infrared Remote function.
Network
Use this function to set up network configurations so that you can control the projector via the network.
Use ▲▼ and the Enter button to select Network and network settings: 
• DHCP  
Set DHCP to ON/OFF. When DHCP is set to ON, the DHCP server of the domain will assign an IP address 
to the projector. The IP address will appear in the IP address window and you dont need to make any 
input. Otherwise, the domain does not or cannot assign any IP address, and 0.0.0.0 is shown on the IP 
address window.
•  IP Address 
To specify an IP address, press the Enter button to show the IP address input window. Use the  ◄►
 button 
to select the number in the address to change. Use the  ▲▼ button to increase or decrease the number in 
the IP address.  Network IP Address 172 . xxx . xxx . xxx 
•  Submask 
Set the submask. The input method is same as the IP address.
•  Gateway 
Set the gateway. The input method is same as the IP address.
•  DNS 
Set the DNS. The input method is same as the IP address
•  Apply Setting  
Apply all the setting to memory if changed.
OSD Menu - Control
Language
Select the OSD language English or Simplified Chinese.
OSD Setting
1.  Menu Position  
Select the OSD pop up position.
2.  Menu Transparency  
Setting the OSD transparency 0%, 25%, 50%, 
75%
3.  Time Out 
Select OSD display timing. Such as Always 
On(press menu button on Remote control or key -
pad to hide the OSD), 10 Seconds, 30 Seconds 
and 60 Seconds.
4.  Message Box  
Select ON or OFF.
To p
Left
Center
Bottom
LeftBottom
Right
To p
Right
100%
0%
75%50%
25%
Blank Screen
Use the  ◄►
 button to select Screen display under no signal status.
Projection Mode 
Use the  ◄►
 button to select a projection mode: Front, Rear, Ceiling + Front, Ceiling + Rear  
Refer to Page 20 [Adjusting the Projection Mode]
Start Using the Projector
Start Using the Projector  
Start Using the Projector
Start Using the Projector