Vivitek Projector DU900 User Manual

DU9000 

1
Index
Safety Notice 4
Copyright   4
Disclaimer   4
About the Manual   4
Disposal of Old Electrical and Electronic Equipment   4
Important Recycling Instructions   4
Important Safety Guidelines   5
Installation and Use Notice   5
Introduction 6
Product Features   6
Packing Checklist   7
Projector Overview  7
General 8
I/O Panel  8
Keypad and LED  9
Keypad   9
Indicator LED  9
Remote Control  10
Installation of the Remote Control Battery  11
Remote Control Operating Range  11
Precautions For Installation...

23
OSD Menu - Control 36
Language 36
OSD Setting  36
Blank Screen  36
Projection Mode   36
Auto Power Off   37
Auto Power On   37
Startup Splash   37
Trigger 1 & 2   37
Auto Source   37
Infrared Remote  37
Network 37
OSD Menu - Service  38
Maintenance 39
Replacing the Lamps  39
How to Replace the Projector Lamp   39
Installing or Removing the Projection Lens  40
Remove Lens  40
Install Lens  40
Replacing the Filter   41
Outline Dimensions 42
Supported Signal Input Timing  43
3D Signal Input Mode & Timing...

45
Important Safety Guidelines 
Thank you for purchasing this high quality product! 
Read the Manual carefully in order to obtain the best performance from y\
our projector, please read the manu-
al completely.
Installation and Use Notice 
1. Please read and keep the manual available for future reference.
2.  Pay attention to all warnings.
3.  Follow all guidelines and recommendations.
4.  Do not put the equipment near water. Do not install the equipment near a heating duct thermal source, 
such as...

67
Packing Checklist 
The following items are included in the DU9000 packaging. If any item is missing or damaged, please contact 
your dealer or Vivitek customer service center.
1. Power Cord (USA, Europe,China)  *3
2.  Remote    *1
3.  Battery (AAA)   *2
4.  Users Manual CD      *1
5.  Warranty Card (For China Only)  *1
6.  HDMI Cable       *1
7.  RHS Card (For China Only)  *1
Projector Overview
Vent 
Heat is discharged from the projector via the vent. Make sure the vent i\
s not blocked.
Intake/Filter...

89
Keypad and LED
ENTER
IR RECEIVER STBY
INPUT
STAND BY
ERROR MENU
ON
LED
STATUS
Keypad 
STBY 
Use STBY button to turn on/off the projector.
INPUT  
Push INPUT button to select the video source. HDMI, SDI, VGA, Component / BNC or H\
DBaseT.
MENU 
Push MENU button to display or hide the OSD menu.
ENTER 
Use ENTER button to select settings or confirm the changed settings. Also push this button to enter and re-
turn to the OSD menu.
Indicator LED
Yellow (Standby)Blue (Power) Red (Error)Status
Standby
Cooling...

1011
Installation of the Remote Control Battery


1.  Slide the battery cover in the direction of the arrow.
2.   Place two AA batteries with the correct polarity.
3.   Slide the cover back.
Battery installation instructions 
• Make sure that batteries are installed with the correct polarity .
• Do not use old and new batteries or mix different types of batteries together.
• Remove the batteries if the remote control will not be used for a long time to prevent. The damage caused by battery leakage....

1213
Cautions on Ventilation 
This product is a high-brightness projector. The intakes with filters are located on the front and right sides to 
provide sufficient air cooling function. The projector has two vents on the back for cool air discharging. Make 
sure the intake and vent are unobstructed when the projector is being installed. At least 50cm around the in-
take and 70cm around the vent should be clear.
Distance must 
>50cm
Distance must 
>70cm
Distance must 
>50cm
Distance must 
>50cm
Ceiling...

1415
Connecting the Projector to Source Devices
Follow the instructions below to connect the DU9000 projector to the video source, external control equip-
ment (if any) and AC power supply. When connecting to the equipment, use the correct signal cable to con-
nect to every signal source and ensure that the cable is securely connected. Fasten the nut on the joint and 
connect the signal source equipment to the projector according to the figure below. 
Connecting to a Computer 
You can connect PC signal to...

1617
Before Using the Projector 
Remove Dust Cover Before Turning on Power
Remove this plastic cover before turning on power and installing Lens.

Connecting to AC Power 
There are three AC power cords included in the box.
Before plug the power cord, please choose the compliant power cord for t\
he AC Voltage in you region.
The fuse is different from 110V and 220V, please switch before you plug power cord.
Plug the power cord to AC socket (AC100V- 240V, please make sure the fuse is in correct Voltage)...