Vivitek Projector DH91x Series User Manual

— 32 — 
Status 
Press the cursor ▲▼ button to move up and down in the Settings 2 menu. Select the Status menu 
and press Enter or ► to enter. 
 
ITEM DESCRIPTION 
Active Source Display the activated source. 
Video Information Displays resolution/video information for RGB source and color standard for Video 
source. 
Lamp Hours Lamp hour used information is displayed. (Eco, Normal, Dynamic Eco) 
Serial Number Showing serial number of product. 
Software Version Showing system software version. 
  

– 33 – 
Advanced 1 Feature 
Press the Menu button to open the OSD menu. Press ◄► to move to the Settings 2 menu. Press 
▲▼ to move to the Advanced 1 menu and then press Enter or ►. Press ▲▼ to move up and down 
in the Advanced 1 menu. Press ◄► to enter and change values for setting. 
 
ITEM DESCRIPTION 
Menu Position Press the cursor ◄► button to enter and select different OSD location. 
Translucent Menu Press the cursor ◄► button to enter and select OSD background translucent level.  
Low Power Mode...

— 34 — 
Lamp Hour Reset 
 
Please refer to Resetting the Lamp on page 49 to reset the lamp hour counter. 
 
Network 
 
ITEM DESCRIPTION 
Network State Displays the network connection status. 
DHCP 
Press ◄► to turn DHCP On or Off. 
Note: If you select DHCP Off, complete the IP Address, Subnet Mask, Gateway, and 
DNS fields. 
IP Address  Enter a valid IP address if DHCP is turned off. 
Subnet Mask Enter a valid Subnet Mask if DHCP is turned off. 
Gateway Enter a valid Gateway address if DHCP is turned...

– 35 – 
LAN_RJ45 
 
Wired LAN Terminal functionalites 
Remote control and monitoring of a projector from a PC (or Laptop) via wired LAN is also possible. 
Compatibility with Crestron / AMX (Device Discovery) / Extron control boxes enables not only collective 
projector management on a network but also management from a control panel on a PC (or Laptop) 
browser screen. 
 Crestron is a registered trademark of Crestron Electronics, Inc. of the United States. 
 Extron is a registered trademark of Extron...

— 36 — 
LAN_RJ45 
1. Connect an RJ45 cable to RJ45 ports on the projector and the PC (Laptop). 
 
2. On the PC (Laptop), select Start → Control Panel →Network and Internet. 
 
   

– 37 – 
3. Right-click on Local Area Connection, and select Properties. 
 
4. In the Properties window, select the Networking tab, and select Internet Protocol (TCP/IP). 
5. Click Properties. 
 
6. Click Use the following IP address and fill in the IP address and Subnet mask, then click OK. 
  

— 38 — 
7. Press the Menu button on the projector. 
8. Select Settings2→ Advanced1 → Network 
9. After getting into Network, input the following: 
 DHCP: Off 
 IP Address: 10.10.10.10 
 Subnet Mask: 255.255.255.0 
 Gateway: 0.0.0.0 
 DNS Server: 0.0.0.0 
10. Press  (Enter) / ► to confirm settings. 
Open a web browser  
(for example, Microsoft Internet Explorer with Adobe Flash Player 9.0 or higher). 
 
11. In the Address bar, input the IP address: 10.10.10.10. 
12. Press  (Enter) / ►. 
The projector...

– 39 – 
 
 
CATEGORY ITEM INPUT-LENGTH 
Crestron Control 
IP Address 15 
IP ID 3 
Port 5 
Projector 
Projector Name 10 
Location 10 
Assigned To 10 
Network Configuration 
DHCP (Enabled) (N/A) 
IP Address 15 
Subnet Mask 15 
Default Gateway 15 
DNS Server 15 
User Password 
Enabled (N/A) 
New Password 10 
Confirm 10 
Admin Password 
Enabled (N/A) 
New Password 10 
Confirm 10 
For more information, please visit http://www.crestron.com.  

— 40 — 
Preparing Email Alerts  
1. Make sure that user can access the homepage of LAN RJ45 function by web browser (for ex-
ample, Microsoft Internet Explorer v6.01/v8.0).  
2. From the Homepage of LAN/RJ45, click Alert Settings.  
 
3. By default, these input boxes in Alert Settings are blank.  
  

– 41 – 
4. For Sending alert mail, input the following: 
SMTP field is the mail server for sending out email (SMTP protocol). This is a required 
field. 
To field is the recipient’s email address (for example, the projector administrator). This is a 
required field.  
Cc field sends a carbon copy of the alert to the specified email address. This is an optional 
field (for example, the projector administrator’s assistant).  
From field is the sender’s email address (for example, the projector...