Vivitek Projector DH558 User Manual

							— 42 — 
TROUBLESHOOTING 
Common problems and solutions 
These guidelines provide tips to deal with problems you may encounter while using the projector. If 
the problem remains unsolved, contact your dealer for assistance. 
Often after time spent troubleshooting, the problem is traced to something as simple as a loose 
connection. Check the following before proceeding to the problem-specific solutions. 
 Use some other electrical device to confirm that the electrical outlet is working. 
 Ensure the projector is turned on. 
 Ensure all connections are securely attached.  
 Ensure the attached device is turned on. 
 Ensure a connected PC is not in suspending mode. 
 Ensure a connected notebook computer is configured for an external display. 
(This is usually done by pressing an Fn-key combination on the notebook.) 
Tips for Troubleshooting 
In each problem-specific section, try the steps in the order suggested. This may help you to solve the 
problem more quickly. 
Try to pin point the problem and thus avoid replacing non-defective parts.  
For example, if you replace batteries and the problem remains, put the original batteries back and go 
to the next step.  
Keep a record of the steps you take when troubleshooting: The information may be useful when 
calling for technical support or for passing on to service personnel. 
  
						

							– 43 – 
LED Error Messages 
ERROR CODE MESSAGES POWER LED 
BLUE 
LAMP LED 
RED 
System Initial Flash OFF 
Ready to Power on (Standby) ON OFF 
System Power on Flash OFF 
Lamp Lit , System stable ON OFF 
Cooling Flashing OFF 
1W MCU detects scaler stops working (initial fail) 2 blinks OFF 
Over Temperature 3 blinks OFF 
Thermal Break Sensor error 4 blinks OFF 
Lamp Fail 5 blinks 0 blinks 
Lamp Temperature shut down 5 blinks 1 blinks 
Lamp Short circuit in output detected 5 blinks 2 blinks 
Lamp End of lamp life detected 5 blinks 3 blinks 
Lamp did not ignite 5 blinks 4 blinks 
Lamp extinguish normal 5 blinks 5 blinks 
Lamp extinguish run-up 5 blinks 6 blinks 
Lamp voltage too low 5 blinks 7 blinks 
Lamp ballast Fail 5 blinks 8 blinks 
Lamp ballast Communication error 5 blinks 10 blinks 
Lamp Fan error(FAN1) 6 blinks 1 blinks 
Power Fan error(FAN2) 6 blinks 2 blinks 
Blower Fan error(FAN3) 6 blinks 3 blinks 
Case Open 7 blinks OFF 
DMD error 8 blinks OFF 
Color wheel error 9 blinks OFF 
In the event of an error, please disconnect the AC power cord and wait for one (1) minute before restarting 
the projector. If the Power or Lamp LEDs are still blinking or any other situation that isnt listed in the chart 
above, please contact your service center. 
Image Problems 
Problem: No image appears on the screen 
1. Verify the settings on your notebook or desktop PC. 
2. Turn off all equipment and power up again in the correct order. 
Problem: The image is blurred  
1. Adjust the Focus on the projector. 
2. Press the Auto button on the remote control. 
3. Ensure the projector-to-screen distance is within the specified range. 
4. Check that the projector lens is clean. 
Problem: The image is wider at the top or bottom (trapezoid effect)  
1. Position the projector so it is as perpendicular to the screen as possible.   
						

							— 44 — 
2. Use the Keystone button on the remote control to correct the problem. 
Problem: The image is reversed  
Check the Projection setting on the Settings 1 menu of the OSD. 
Problem: The image is streaked  
1. Set the Frequency and Tracking settings on the Image->Computer menu of the OSD to 
the default settings. 
2. To ensure the problem is not caused by a connected PC’s video card, connect to another 
computer.  
Problem: The image is flat with no contrast  
Adjust the Contrast setting on the Image menu of the OSD. 
Problem: The color of the projected image does not match the source image. 
Adjust the Color Temperature and Gamma settings on the Image->Advanced menu of the 
OSD. 
Lamp Problems 
Problem: There is no light from the projector  
1. Check that the power cable is securely connected. 
2. Ensure the power source is good by testing with another electrical device. 
3. Restart the projector in the correct order and check that the Power LED is on. 
4. If you have replaced the lamp recently, try resetting the lamp connections.  
5. Replace the lamp module. 
6. Put the old lamp back in the projector and have the projector serviced. 
Problem: The lamp goes off 
1. Power surges can cause the lamp to turn off. Re-plug power cord. When the Power LED 
is on, press the power button. 
2. Replace the lamp module. 
3. Put the old lamp back in the projector and have the projector serviced. 
Remote Control Problems 
Problem: The projector does not respond to the remote control  
1. Direct the remote control towards remote sensor on the projector.  
2. Ensure the path between remote and sensor is not obstructed. 
3. Turn off any fluorescent lights in the room. 
4. Check the battery polarity. 
5. Replace the battery. 
6. Turn off other Infrared-enabled devices in the vicinity. 
7. Have the remote control serviced. 
Audio Problems 
Problem: There is no sound 
1. Adjust the volume on the remote control.  
2. Adjust the volume of the audio source. 
3. Check the audio cable connection. 
4. Test the source audio output with other speakers.  
						

							– 45 – 
5. Have the projector serviced. 
Problem: The sound is distorted  
1. Check the audio cable connection. 
2. Test the source audio output with other speakers. 
3. Have the projector serviced. 
Having the Projector Serviced 
If you are unable to solve the problem, you should have the projector serviced. Pack the projector in 
the original carton. Include a description of the problem and a checklist of the steps you took when 
trying to fix the problem: The information may be useful to service personnel. For servicing, return the 
projector to the place you purchased it.  
						

							— 46 — 
HDMI Q & A 
Q. What is the difference between a “Standard” HDMI cable and a “High-Speed” HDMI 
cable? 
Recently, HDMI Licensing, LLC announced that cables would be tested as Standard or High-
Speed cables.  
˙Standard (or “category 1”) HDMI cables have been tested to perform at speeds of 75Mhz or 
up to 2.25Gbps, which is the equivalent of a 720p/1080i signal.  
˙High Speed (or “category 2”) HDMI cables have been tested to perform at speeds of 340Mhz 
or up to 10.2Gbps, which is the highest bandwidth currently available over an HDMI cable 
and can successfully handle 1080p signals including those at increased color depths and/or 
increased refresh rates from the Source. High-Speed cables are also able to accommodate 
higher resolution displays, such as WQXGA cinema monitors (resolution of 2560 x 1600). 
 
Q. How do I run HDMI cables longer than 10 meters? 
There are many HDMI Adopters working on HDMI solutions that extend a cable’s effective 
distance from the typical 10 meter range to much longer lengths. These companies 
manufacture a variety of solutions that include active cables (active electronics built into 
cables that boost and extend the cable’s signal), repeaters, amplifiers as well as CAT5/6 and 
fiber solutions. 
 
Q. How can I tell if a cable is an HDMI certified cable? 
All HDMI products are required to be certified by the manufacturer as part of the HDMI 
Compliance Test Specification. However, there may be instances where cables bearing the 
HDMI logo are available but have not been properly tested. HDMI Licensing, LLC actively 
investigates these instances to ensure that the HDMI trademark is properly used in the 
market. We recommend that consumers buy their cables from a reputable source and a 
company that is trusted. 
 
For more detail information check http://www.hdmi.org/learningcenter/faq.aspx#49 
 
  
						

							– 47 – 
SPECIFICATIONS 
Specifications 
Model DH558 / DH559 
DH559 Display Type TI DMD 0.65  S600 1080P 
Resolution 1920x1080 
Projection Distance 1 ~ 10 m 
Projection Screen Size 31 ~ 308.8 
Projection Lens Manual Focus/ Manual Zoom 
Zoom Ratio 1.2x 
Vertical Keystone 
Correction +/- 40 Degree 
Projection Methods Front, Rear, Desktop/Ceiling (Rear, Front) 
Data Compatibility VGA, SVGA, XGA, SXGA, SXGA+, UXGA, WUXGA@60hz,  Mac 
SDTV/EDTV/ HDTV 480i, 480p, 576i, 576p, 720p, 1080i, 1080p 
Video Compatibility NTSC, PAL, SECAM 
H-Sync 15, 30~91.4KHz 
V-Sync 24~30Hz, 47~120Hz 
Safety Certification FCC-B, cUL, UL, UL-AR, CE, CB, KC, NOM, CCC 
Operation Temperature 5° ~ 40°C 
Dimensions 274.6 mm (W) x 212 mm (D) x 100 mm (H) 
Ac Input AC Universal 100-240V 
Power Consumption 240W (Normal), 200W (ECO), 
						

							— 48 — 
Projection Distance vs. Projection Size 
 
Projection Distance and Size Table 
DH558 / DH559 
IMAGE DIAGONAL IMAGE WIDTH IMAGE HEIGHT 
PROJECTION 
DISTANCE 
FROM 
PROJECTION 
DISTANCE 
TO 
OFFSET-A 
(INCH) (INCH) (CM) (INCH) (CM) (INCH) (CM) (INCH) (CM) (MM) 
60 52.3 132.8 29.4 74.7 63.8 162.1 76.4 193.9 112.1 
70 61.0 154.9 34.3 87.1 74.4 189.1 89.1 226.3 130.8 
72 62.8 159.5 35.3 89.7 76.6 194.5 91.6 232.7 134.5 
80 69.7 177.0 39.2 99.6 85.1 216.1 101.8 258.6 149.4 
84 73.2 185.9 41.2 104.6 89.3 226.9 106.9 271.5 156.9 
90 78.4 199.1 44.1 112.0 95.7 243.1 114.5 290.9 168.1 
96 83.7 212.6 47.1 119.6 102.1 259.3 122.2 310.3 179.3 
100 87.2 221.5 49.0 124.5 106.3 270.1 127.3 323.2 186.8 
120 104.6 265.7 58.8 149.4 127.6 324.1 152.7 387.9 224.1 
135 117.7 299.0 66.2 168.1 143.5 364.6 171.8 436.3 252.2 
150 130.7 332.0 73.5 186.7 159.5 405.1 190.9 484.8 280.2 
200 174.3 442.7 98.1 249.2 212.7 540.2 254.5 646.4 373.6 
 
 
 
    
						

							– 49 – 
Timing Mode Table 
SIGNAL RESOLUTION H-SYNC  
(KHZ) 
V-SYNC 
(HZ) 
COMPOSITE 
/ S-VIDEO COMPONENT RGB DVI/ 
HDMI 
NTSC － 15.734 60.0 O － － － 
PAL/SECAM － 15.625 50.0 O － － － 
VESA 
720 x 400 37.9 85.0 － － O O 
640 x 480 31.5 60.0 － － O O 
640 x 480 37.9 72.8 － － O O 
640 x 480 37.5 75.0 － － O O 
640 x 480 43.3 85.0 － － O O 
800 x 600 35.2 56.3 － － O O 
800 x 600 37.9 60.3 － － O O 
800 x 600 46.9 75.0 － － O O 
800 x 600 48.1 72.2 － － O O 
800 x 600 53.7 85.1 － － O O 
800 x 600 76.3 120.0 － － O O 
1024 x 768 48.4 60.0 － － O O 
1024 x 768 56.5 70.1 － － O O 
1024 x 768 60.0 75.0 － － O O 
1024 x 768 68.7 85.0 － － O O 
1024 x 768 97,6 120.0 － － O O 
1280 x 720 45.0 60.0 － － O O 
1280 x 720 91.5 119.9 － － O O 
1280 x 800 49.7 59.8 － － O O 
1280 x 800 62.8 74.9 － － O O 
1280 x 800 71.6 84.8 － － O O 
1280 x 800 101.6 119.9 － － O O 
1280 x 1024 64.0 60.0 － － O O 
1280 x 1024 80.0 75.0 － － O O 
1280 x 1024 91.1 85.0 － － O O 
1280 x 960 60.0 60.0 － － O O 
1280 x 960 85.9 85.0 － － O O 
1400 x 1050 65.3 60.0 － － O O 
1440 x 900 70.6 75.0 － － O O  
						

							— 50 — 
SIGNAL RESOLUTION H-SYNC  
(KHZ) 
V-SYNC 
(HZ) 
COMPOSITE 
/ S-VIDEO COMPONENT RGB DVI/ 
HDMI 
1440 x 900 55.9 60.0 － － O O 
1600 x1200 75.0 60 － － O O 
1680 x 1050 64.7 59.9 － － O O 
1680 x 1050 65.3 60 － － O O 
1920 x 1080 67.5 60 － － O O 
1920 x 1200 74 60 － － O O 
Apple Mac 
640 x 480 35.0 66.7 － － O O 
832 x 624 49.7 74.5 － － O O 
1024 x 768 60.2 74.9 － － O O 
1152 x 870 68.7 75.1 － － O O 
SDTV 
480i 15.734 60.0 － O － O 
576i 15.625 50.0 － O － O 
EDTV 
576p 31.3 50.0 － O － O 
480p 31.5 60.0 － O － O 
HDTV 
720p 37.5 50.0 － O － O 
720p 45.0 60.0 － O － O 
1080i 33.8 60.0 － O － O 
1080i 28.1 50.0 － O － O 
1080p 67.5 60.0 － O － O 
1080p 56.3 50.0 － O － O 
1080p 27 24.0 － O － O 
1080p 28 25.0 － O － O 
1080p 33.7 30.0 － O － O 
O：Frequency supported 
—：Frequency not supported 
*：The color of      mean may have a little noise is acceptable 
*：HDTV timing main check tool is DVD player, VG828 is secondary.  
						

							– 51 – 
Projector Dimensions 
 
 2 7 4 . 6 m m
[ 1 0 . 8  ]
2
1
2
m
m
[8
.3
4
6

]
1
0
0
.
3
m
m
[
3
.9
5

]
8
6
m
m
[
3
.3
8
6

]