Vivitek Projector D967 User Manual
Have a look at the manual Vivitek Projector D967 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 263 Vivitek manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
DLP Projector—User’s Manual Lamp Hour Reset Please refer to Resetting the Lamp on page 48 to reset the lamp hour counter. Network ITEM DESCRIPTION Network State Displays the network connection status. DHCP Press ◄► to turn DHCP On or Off. Note: If you select DHCP Off, complete the IP Address, Subnet Mask, Gateway, and DNS fields. IP Address Enter a valid IP address if DHCP is turned off. Subnet Mask Enter a valid Subnet Mask if DHCP is turned off. Gateway Enter a valid Gateway address if DHCP is turned off. DNS Enter a valid DNS name if DHCP is turned off. Apply Press (Enter) / ► to confirm settings. – 33 –
DLP Projector—User’s Manual LAN_RJ45 Wired LAN Terminal functionalites Remote control and monitoring of a projector from a PC (or Laptop) via wired LAN is also possible. Compatibility with Crestron / AMX (Device Discovery) / Extron control boxes enables not only collective projector management on a network but also management from a control panel on a PC (or Laptop) browser screen. Crestron is a registered tra demark of Crestron Electronics, Inc. of the United States. Extron is a registered trademark of Extron Electronics, Inc. of the United States. AMX is a registered trademark of AMX LLC of the United States. PJLink applied for trademark and logo registra tion in Japan, the United States of America, and other countries by JBMIA. Supported External Devices This projector is supported by the specified co mmands of the Crestron Electronics controller and related software (ex, RoomView ®). http://www.crestron.com/ This projector is supported by AMX ( Device Discovery ). http://www.amx.com/ This projector is compliant to supp ort Extron device(s) for reference. http://www.extron.com/ This projector supports all commands of PJLink Class1 (Version 1.00). http://pjlink.jbmia.or.jp/english/ For more detail of information about the diverse types of external devices which can be connected to the LAN/RJ45 port and remote/control the projector, as well as the related control commands supporting for each external device, kindly please get contac t with the Support-Service team directly. — 34 —
DLP Projector—User’s Manual LAN_RJ45 1. Connect an RJ45 cable to RJ45 ports on the projector and the PC (Laptop). 2. On the PC (Laptop), select Start → Control Panel → Network Connections . – 35 –
DLP Projector—User’s Manual 3. Right-click on Local Area Connection , and select Properties. 4. In the Properties window, select the General tab, and select Internet Protocol (TCP/IP) . 5. Click Properties . 6. Click Use the following IP address and fill in the IP address and Subnet mask, then click OK. — 36 —
DLP Projector—User’s Manual 7. Press the Menu button on the projector. 8. Select Settings2→ Advanced1 → Network 9. After getting into Network, input the following: DHCP: Off IP Address: 10.10.10.10 Subnet Mask: 255.255.255.0 Gateway: 0.0.0.0 DNS Server: 0.0.0.0 10. Press (Enter) / ► to confirm settings. Open a web browser (for example, Microsoft Internet Explorer with Adobe Flash Player 9.0 or higher). 11. In the Address bar, input the IP address: 10.10.10.10. 12. Press (Enter) / ► . The projector is setup for remote managemen t. The LAN/RJ45 function displays as follows. – 37 –
DLP Projector—User’s Manual CATEGORY ITEM INPUT-LENGTH IP Address 15 IP ID 3 Crestron Control Port 5 Projector Name 10 Location 10 Projector Assigned To 10 DHCP (Enabled) (N/A) IP Address 15 Subnet Mask 15 Default Gateway 15 Network Configuration DNS Server 15 Enabled (N/A) New Password 10 User Password Confirm 10 Enabled (N/A) New Password 10 Admin Password Confirm 10 For more information, please visit http://www.crestron.com. — 38 —
DLP Projector—User’s Manual Preparing Email Alerts 1. Make sure that user can access the homepage of LAN RJ45 function by web browser (for ex- ample, Microsoft Internet Explorer v6.01/v8.0). 2. From the Homepage of LAN/RJ45, click Alert Settings. 3. By default, these input boxes in Alert Settings are blank. – 39 –
DLP Projector—User’s Manual 4. For Sending alert mail, input the following: The SMTP field is the mail server for sending out email (SMTP protocol). This is a required field. The To field is the recipient’s email address (for exam ple, the projector administrator). This is a required field. The Cc field sends a carbon copy of the alert to th e specified email address. This is an optional field (for example, the projecto r administrator’s assistant). The From field is the sender’s email address (for exampl e, the projector administrator). This is a required field. Select the alert conditions by checking the desired boxes. Note: Fill in all fields as specified. User can click Send Test Mail to test what setting is correct. For successful sending an e-mail alert, you must sele ct alert conditions and enter a correct e-mail address. — 40 —
DLP Projector—User’s Manual RS232 by Telnet Function Besides projector connected to RS232 interface with “Hyper-Ter minal” communication by dedicated RS232 command control, there is alternative RS232 command control way, so called “RS232 by TELNET” for LAN/RJ45 interface. Quick Start-Guide for “RS232 by TELNET” Check and get the IP-Address on OSD of the projector. Make sure that laptop/PC can acce ss the web-page of the projector. Make sure that “Windows Firewall” setting to be di sabled in case of “TELNET” function filtering out by laptop/PC. Start => All Programs => Accessories => Command Prompt – 41 –
DLP Projector—User’s Manual Input the command format like the below: telnet ttt.xxx.yyy.zzz 23 (“Enter” key pressed) ( ttt.xxx.yyy.zzz : IP-Address of the projector) If Telnet-Connection ready, and us er can have RS232 command inpu t, then “Enter” key pressed, the RS232 command will be workable. How to have TELNET enabled in Windows VISTA / 7 By default installation for Windows VISTA, “TELNE T” function is not included. But end-user can have it by way of “Turn Windows features On or Off” to be enabled. Open “Control Panel” in Windows VISTA Open “Programs” — 42 —