Vivitek Projector D8800 Series User Manual

							51
DLP Projector - User’s Manual
Change Filter
The filter should be changed every 3000 hours.
To replace the Filter on the left side of the projector
1. Remove the cover on the left side of the projector.
2. Remove the filter from it.
3. Insert a new filter.
4 . Install the cover on the left side of the projector.   
						

							DLP Projector - User’s Manual
52
To replace the Filter on the right side of the projector
1. Loosen the fan cover on the right side of the projec-
t o r.
2. Open the fan cover and remove the filter from it.
3. Insert a new filter and install the fan cover on the 
right side of the projector.
4 . Secure the fan cover.
 
„ Optional component
Component P/ N
Handle D88-Acc-HDL-00
Foot D88-Acc-Fot-00
Filter D88-AF00   
						

							53
DLP Projector - User’s Manual
Change the Color Wheel
The color wheel is on the top side.
j Loosen the top cover
    Slide the cover and remove it.  k Loosen the color wheel’s screw.
l Life up the color Wheel
²
Ç
o Slide the bracket to recover 
    the machine then use the 
    screw to fix the top bracket 
    on the machine. m Replace the color wheel 
    that you wanted.
n Tighten the screws.
Ç
²           
						

							DLP Projector - User’s Manual
54
LED Status
SHUTTER
TEMP.LAMP 1LAMP 2STATUSPOWER
Power LED
LED DisplayProjector status Procedure
Off Power is off
Flashing GreenPrepare to turn on projector Wait till projector start displaying
Orange Projector cooling Wait until cooling finish ( ~ 90 sec)
On RedStandby mode
Green Projector is on
Status LED
LED Display Projector status Procedure
Off No Problem
Flashing Red (Cycles of 1)Cover Problem Contact local Vivitek Server Center
Red (Cycles of 4) Fan Problem Contact local Vivitek Server Center
On RedSystem Error Contact local Vivitek Server Center
Lamp1/Lamp2 LED
LED Display Projector status Procedure
Off Lamp off
Flashing GreenPrepare to light lamp
Red (Cycles of 6) Lamp lit fail
On RedLamp is end-of-life
Green Lamp lit
Temp LED
LED Display Projector status Procedure
Off No Problem
Flashing RedTemperature problem Contact local Vivitek Server Center
Shutter LED
LED Display Projector status Procedure
Off Shutter is open
Flashing GreenShutter is closed   
						

							55
DLP Projector - User’s Manual
SPECIFICATIONS
ModelD8800D8900D8010W
Display Type DLP
Brightness 8000 ANS Lumens10,000 ANS Lumens8000 ANS Lumens
Native Resolution WUXGA (1920 x 1200)XGA (1024 x 768)WXGA (1280 x 800)
Maximum Resolution WUXGA (1920 x 1200)@60Hz
Contrast Ratio 3000:1
Lamp Life and Type 2000/2500 Hours (Std. / Eco Mode), 400W x 2
Throw Ratio (Standard Lens) 1.73 - 2.27:11.79-2.35:11.81-2.38:1
Image Size (Diagonal) 40”- 500”40”- 500”40”- 500”
Projection Distance 1.83 – 14.9m (6 - 49ft)1.79 – 14.54m (5.87 – 47.07ft)1.93 – 15.64m (6.3 – 51.31ft)
Projection Lens F = 1.7 - 1.9
f = 25.7 - 33.7mm
Zoom Ratio (Standard Lens) 1.3X
Aspect Ratio 16.10 Native, 4.3 and 16:9 Compatible
Offset 0% ~ +50%
Keystone Correction Vertical: +/-30°
Horizontal:+/-35°
Synchronization Vertical: 48 - 120 Hz
Horizontal: 15 - 108kHz
Edge Blending Yes (built-in)
Lens Shift Range Vertical: +/- 50%
Horizontal: +/- 10%
Video Compatibility SDTV(480i/576i), EDTV (480p/576p), HDTV (720p, 1080i/p), NTSC/NTSC 4.43, PAL B/G/H/I/
M/N 60, SECAM
I/O Connection Ports HDMI v1.3, DVI-D, Component (YPbPr), VGA-In (x2), S-Video, Composite, 3G HDSDI-In, 3G 
HDSDI-Out, RJ45, 12V Trigger, RS-232C, Wired Remote
Projection Method Table Top, Ceiling Mount (Front or Rear)
Dimensions (W x D x W) 508 x 552.6 x 229mm (20” x 21.8” x 9”)
Weight (Without Lens) 24kg (52.9lbs)
Noise Level 39 dB/39 dB (Single Lamp Eco./Std Mode)
39 dB/43 dB (Dual Lamp Eco./Std Mode)
Power Supply AC 100-240V, 50/60Hz
Power Consumption
Lamp Style Dual LampSingle Lamp
220V 960W 450W
110V 995W 440W
Standby: 0.5W (Without RJ-45, RS-232 Enabled)
Standard Accessories AC Power Cord 
VGA Cable 
Remote Control 
Lens Cap 
Documentation Kit
Optional Accessories Replacement Lamp 
Remote 
Carry Handle 
Foot Socket 
Interchangeable Lens Options (x6)   
						

							DLP Projector - User’s Manual
56
SERIAL INTERFACE SPECIFICATIONS
Transfer Specifications
ItemSpecifications
Transmission Speed 38400 bps
Data Length 8 bit
Parity None
Stop Bit 1
Flow Control None
RS-232 Commands
There are 2 types of commands:
 
y Key commands 
 
y Operation commands 
All commands start with 2 letters as shown in the following:   
y “ky” for key commands. 
 
y “op” for operations commands. 
 
y Key Commands The following example is the syntax for key commands: ky  [CR]
IR Codes and Key names
Key Code RS232 Key name Key Wording Description
1 0x90 ONTurn power on.
2 0x91 OFFTurn power off.
3 0xB6 FOCUS+
4 0xB7 ZOOM+Zoom in.
5 0xB8 TEST PATTERNEnter test pattern menu.
6  0xB9 FOCUS-
7 0xBA ZOOM-Zoom out.
8 0xBB LENS SHIFTShift control of the lens.
9 0xC1
Keypad up arrow.
10 0xC3
Keypad left arrow.
11 0xC4
Keypad right arrow.
12 0xC5 ENTERKeypad enter.
13 0xC2
Keypad down arrow.
14 0x87 MENUShow or hide the OSD menu.
15 0xBC EXITExit the OSD menu.
16 0x83 INPUTSwitch the active source.
17 0x98 PICTUREOpen PICTURE menu.
18 0x8C NETWORK
19 0x86 AUTO SYNC
20 0x9F ASPECTSwitch to the next aspect ratio.
21 0x8F PIP
22 0xBD OVERSCAN
23 0x8E FREEZE
24 0x8b LAMP MODE
25 0xBE 3D MODENot available.
26 0xBF INFOOpen SERVICE menu.   
						

							57
DLP Projector - User’s Manual
KeyCode RS232 Key name Key Wording Description
27 0x9E LIGHT
28 0x9A CLEARNot available.
29 0x9B SHUTTERTurn on or off the shutter.
30 0x9C ID SETNot available.
Operations Commands
The following example is the syntax for operations commands:
 op   [CR]
No. Function Command Action on unit
1 Set =Makes the unit take that value.
2 Get ?Asks what the current value is.
3 Increment +Adds 1 to the current value.
4 Decrement -Subtracts 1 from the current value.
5 Execute (none)Performs an action.
Operation Command Values
1. INPUT
input.sel= ?0 = HDMI
1 = DVI
2 = VGA
3 = Component / BNC
4 = Composite
5 = S-Video
6 = 3G-SDI
7 = Option Board (Reserved)
pip = ?0 = Off
1 = On
pip.sel = ?1 = HDMI
2 = DVI
3 = VGA
4 = Component / BNC
5 = Composite
6 = S-Video
7 = 3G-SDI
8 = Option Board (Reserved)
pip.swap (execute)Swap main and PIP source
pip.pos = ?0 = Top Left
1 = Top Right
2 = Bottom Left
3 = Bottom Right
4 = Split L-R   
						

							DLP Projector - User’s Manual
58
OperationCommand Values
pattern = ?0 = Color Bar
1 = Cross Hatch
2 = Burst
3 = Red
4 = Green
5= Blue
6 = White
7 = Black
8 = Red (TI)
9 = Green (TI)
10 = Blue (TI)
11 = HRamp (TI)
12 = Off
color.space = ?0 = Auto
1 = YCbCr
2 = YPbPr
3 = RGB-PC (0-255)
4 = RGB-Video (16-235)
input.lock = ?0 = Auto
1 = 48 Hz
2 = 50 Hz
3 = 60 Hz
no.signal = ?0 = Logo
1 = Blue
2 = Black
3 = White
vid.std = ?0 = Auto
1 = PAL
2 = SECAM
3 = NTSC
auto.imgadj = ?0 = Off
1 = Auto
2 = Always
2. PICTURE
pic.mode= ?0 = High Bright
1 = Presentation
2 = Video
contrast = ? + -0 - 200
dyna.cont = ?0 = Off
1 = On
bright = ? + -0 - 200
saturat = ? + -0 - 200
tint = ? + -0 - 200
gamma = ?0 = Film
1 = Graphics
2 = Video
3 = Linear
color.temp (pic.mode is “High Bright” 
or “Presentation”) = ?
0 = Default
1 = Native
color.temp ( pic.mode is “Video”) = ?0 = 5000K
1 = 6500K
2 = 7800K
3 = 9300K
4 = Native   
						

							59
DLP Projector - User’s Manual
OperationCommand Values
red.offset = ? + -0-200
green.offset = ? + -0-200
blue.offset = ? + -0-200
red.gain = ? + -0-200
green.gain = ? + -0-200
blue.gain = ? + -0-200
sharp = ? + -0-200
nr = ? + -0-200 (Noise Reduction)
aspect = ?0 = 5:4
1 = 4:3
2 = 16:10
3 = 16:9
4 = 1.88
5 = 2.35
6 = Letterbox
7 = Native
8 =Unscaled
zoom (Overscan) = ?0 = 5:4
1 = 4:3
2 = 16:10
3 = 16:9
4 = 1.88
5 = 2.35
6 = Letterbox
7 = Native
8 =Unscaled
h.total = ? + -0-200
h.pos = ? + -0-200
h.phase = ? + -0-200
v.pos = ? + -0-200
auto.img (Auto Sync) (execute)
3. LAMP
lamps= ?0 = Single
1 = Dual
lamp.mode (Drive) = ?0 = Economy
1 = Standard
2 = Dimming
lamp.pwr = ?0-25 (80.4 % ~100.0 %)
altitude (High Altitude) = ?0 = Off
1 = On
lamp1.stat ?0 = Off
1 = On
lamp2.stat ?0 = Off
1 = On
4. ALIGNMENT
proj.mode= ?0 = Front
1 = Rear
2 = Ceiling + Front
3 = Ceiling + Rear   
						

							DLP Projector - User’s Manual
60
OperationCommand Values
fan.pos = ?0 = Normal
1 = Vertical
2 = Down
zoomio + -+ => Zoom out
- => Zoom in
focus + -+ => Focus Near
- => Focus Far
vert.offset + -+ => Up
- => Down
horiz.offset + -+ => Right
- => Left
lens.load =1~10 set of lens memory (Load)
lens.save =1~10 set of lens memory (Save)
lens.center (execute)Midposition shift
h.keystone = ? + --350~+350
v.keystone = ? + --200~+200
warp.rotat = ? + --20 ~ +20 (in ¼ 1/4 unit)
warp.pinbrl = ? + --100 ~ +100
warp.tlc.x
warp.tlc.y = ? + -
‘x: -192 ~ +192
‘y: -120 ~ +120
warp.trc.x
warp.trc.y = ? + -
‘x: -192 ~ +192
‘y: -120 ~ +120
warp.blc.x
warp.blc.y = ? + -
‘x: -192 ~ +192
‘y: -120 ~ +120
warp.brc.x
warp.brc.y = ? + -
‘x: -192 ~ +192
‘y: -120 ~ +120
warp.cust = ?0 = Off
1 = On
warp.reset (execute)
blank.top = ? + -0 ~ 360
blank.btm = ? + -0 ~ 360
blank.left = ? + -0 ~ 534
blank.right = ? + -0 ~ 534
blank.rst (execute)
eb.stat (Edge Blend) = ?
eb.wht.top = ? + -0, 200 ~ 500
eb.wht.btm = ? + -0, 200 ~ 500
eb.wht.left = ? + -0, 200 ~ 800
eb.wht.right = ? + -0, 200 ~ 800
eb.blk.top = ? + -0, 8, 16, 24, 32
eb.blk.btm = ? + -0, 8, 16, 24, 32
eb.blk.left = ? + -0, 4, 8, 12, 16, 20, 24, 28, 32
eb.blk.right = ? + -0, 4, 8, 12, 16, 20, 24, 28, 32
eb.all = ? + -0 ~ 32
eb.red = ? + -0 ~ 32
eb.green = ? + -0 ~ 32
eb.blue = ? + -0 ~ 32
eb.reset (execute)