Vivitek Projector D5280U User Manual

 P
P
P r
r
r e
e
e f
f
f a
a
a c
c
c e
e
e  
 
 
Starting and Shutting  down the Projector 
1.  Remove the lens cap. 
2.  Securely connect the power cord and 
signal cable. When connected, the 
power led will turn red. 
 
 
3.  Turn on the lamp by pressing 
“
” button on the rear of the pro-
jector or “
” on the remote control. 
The PWR LED will now flash green.  
The startup screen will display in ap-
proximately 30 seconds. The first time 
you use the projector, you can select 
your preferred language...

DLP Projector—User’s Manual 
4.  If more than one input device is con-
nected, press the SOURCE button and 
use  ▲▼  to scroll among devices. 
(Component is supported through the 
RGB to COMPONENT ADAPTER.) 
 
 
•   PC 1 / 2: Analog RGB 
DVD input YCbCr/ YPbPr, or HDTV input 
YPbPr via D-sub connector 
•   HDMI: High-Definition Multimedia Interface com-
patible 
•   DisplayPort: Digital display interface 
•   BNC: Analog RGB 
•   COMPONENT: DVD input YCbCr/ YPbPr, or 
HDTV input YPbPr 
•   VIDEO:...

 P
P
P r
r
r e
e
e f
f
f a
a
a c
c
c e
e
e  
 
 
Adjusting the Projector Level 
Take note of the following when setting up the projector: 
•   The projector table or stand should be level and sturdy. 
•   Position the projector so that it is perpendicular to the screen. 
•   Remove the Back Foot Holder on the rear adjuster foot before adjusting the projection  
angle. 
•   Ensure the cables are in a safe location. You could trip over them.  
 
1.  To raise the level of the projector, twist 
the adjusters...

DLP Projector—User’s Manual 
Adjusting Projected Image Position Using Shift 
 
The Shift feature provides a lens shift function that can be used to adjust the position of the projected 
image either horizontally or vertica lly within the range detailed below. 
Shift is a unique system that provid es lens shift while maintaining a much higher ANSI contrast ratio 
than traditional lens shift systems. 
Adjusting the vertical image position 
The vertical image height can be  adjusted between 110% and -30% of...

 P
P
P r
r
r e
e
e f
f
f a
a
a c
c
c e
e
e  
 
 
Adjusting the horizontal image position 
With the lens in the center posit ion the horizontal image position can be adjusted to the left or right by 
up to a maximum of 10% of the half image width.  Note that the maximum horizontal image height ad-
justment can be limited by the vertical image position. For example it  is not possible to achieve the 
maximum horizontal image position if  the vertical image position is at maximum. Please consult the 
Shift...

DLP Projector—User’s Manual 
Adjusting the Zoom, Focus and Keystone 
1.  Use the Image-zoom   
control (on the projector 
only) to resize the pro-
jected image and screen 
size. 
 
2.  Use the  Image-focus   
control (on the projector 
only) to sharpen the pro-
jected image. 
 
3.  Use the  KEYSTONE  
buttons (on the projector 
or the remote control) to 
correct image-trapezoid 
(wider top or bottom)  
effect. 
 
Remote control and OSD panel 
4.  The keystone control  
appears on the display. 
 
—  18 —  

 P
P
P r
r
r e
e
e f
f
f a
a
a c
c
c e
e
e  
 
 
Adjusting the Volume 
1.  Press the  Volume +/-   
buttons on the remote 
control.  
The volume control  
appears on the display. 
2.  Press the  Left or Right 
Cursor  buttons on the 
keypad to adjust  Volume 
+/-. 
 
3.  Press the  MUTE button to 
turn off the volume (This 
feature is available only 
on the remote). 
 
 
 
– 19  –  

DLP Projector—User’s Manual 
— 20 — 
ON-SCREEN DISPLAY (OSD) MENU SETTINGS 
OSD Menu Controls 
The projector has an OSD that lets you ma ke image adjustments and change various settings.  
Navigating the OSD 
You can use the remote control curs or buttons or the buttons on the top of the projector to navigate 
and make changes to the OSD. The following illu stration shows the corresponding buttons on the 
projector. 
13
16
5
2
7
24
1
1
3
4
5
6
7
 
1.  To enter the OSD, press the  MENU button. 
2.  There...

 P
P
P r
r
r e
e
e f
f
f a
a
a c
c
c e
e
e  
 
 
Setting the OSD Language 
Set the OSD language to your pr eference before continuing. 
1. Press the MENU button. Press the cursor  ◄► button to navigate to  SETUP>>Basic. 
 
2. Press the cursor ▲▼  button until Language is highlighted.  
3. Press the cursor ◄►  button until the language you want is selected.  
4. Press the MENU button to close the OSD.   
– 21  –  

DLP Projector—User’s Manual 
OSD Menu Overview 
Use the following illustration to quickly find a setting or determine the range for a setting. 
PICTURE>> BasicDisplay ModeBrightness
TintColorContrast
Sharpness
Movie/Bright/Normal/User 1/User 2/User 3
Flesh Tone
PICTURE>> AdvancedNoise ReductionColor TemperatureGammaHSG AdjustmentColor Space
Warm/Normal/Cool/Cooler/High Cool
Auto/RGB/STDV/HDTV
DISPLAYAspect RatioKeystoneOverscanDigital Zoom
Auto/16:10/16:9/4:3/Letter Box/Real
SYSTEM SETUP >>...